Having problems with your 2004 Kia Optima ?
Auto Dim-Home link rear view mirror-ball joint popped out of hole
\015 My Auto Dim with Home link rear view mirror that\342\200\231s attached to the swivel ball joint popped out of the swivel hole with the electrical wire still attached to both the mirror and the mount attached to the windshield and I can't get it to pop back in. How can I get it to do so?\015
Repair Help & Product Troubleshooting for 2004 Kia Optima
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Auto Dim-Home link rear view mirror-ball joint popped out of hole
... 2004 Kia Optima
Home Link Rear View Mirror
I've read that there was a problem with the instructions in the '07 manual. Maybe it was carried over to '08 model too. I'd try the Homelink website for instructions particular to your setup: ... 2008 Toyota Camry
My rear view mirror fell off the ball joint that connects it to the glass. How do i get it back on?
You can't . \015\012You have to go to the dealer for a new Review Mirror. \015\012\015\012Sorry,\015\012\015\012Good luck ... 2005 Chevrolet Equinox
My 1986 toyota corolla's rear view mirror is lose at the ball joint. is there any way to tighten it?
My 1998 corolla rear view mirror is loose. How can I tighten it? ... 1986 Toyota Corolla 2 Door
The rear view mirror came off of the ball joint. how do i get it back on?
... 2007 Mazda MAZDA6
Rear view mirror loose at ball joint - 2004 Saturn VUE
... 2004 Saturn VUE
How do i dismantle a peugeot 505 rear view mirror? the inside ball joint has un hinged slightly and now is too loose... the out side rubber grommit has no screws and i don't want to force or pry or break..... thanks
... 1986 Peugeot 505
How to fix the ball joint connections of rear view mirror
... 2005 Chevrolet Equinox
Need to replace the lower ball joints in my 2002 Dodge Durango SXT. Receiving conflicting advise. Some say that I have to replace the whole control arm with new ball joint. Others say that I can press the old ones out of the control arm and press new ball joints with grease fittings up into it... the existing ball joints are factory and do not have grease fittings. I can't be sure, but it looks like the top of control arm that houses the ball joint is solid cast. It doesn't appear to be a "hole"
It looks like if you buy the joint from Chrysler then it comes complete with the arm however there are aftermarket companies that make just the ball joint which can be pressed in and out. It's fairly common for a manufacturer to offer the joint only ... 2002 Dodge Durango
Ball joint on hilux surf gen 3 popped out
Didn't it have a castellated nut and a cotter pin? If no cotter pin, maybe the nut worked itself back off, or wasn't tightened enough. Fit it back on to test fit: the ball stud should be smaller diameter at top and get larger towards bottom, so it ... 1993 Toyota Pickup
Right front upper control arm / ball joint i have a 1998 honda passport that needs a ball joint in staled. i also have a 1999 isuzo rodieo that i bought for parts would it be better to just repace the hole control arm than to remove the ball jount and the intall the ball joint? and need to know where to go for a digram on how to remove eather of the item let me know what you think
... 1998 Honda Passport
My Tahoe has some play in the steering. I took it into an independent garage and was told the pitman and idler arms needed replacing. Knowing I could do the work myself, I drove the beast home and crawled under it to take a look. Everything but the ball joint on the pitman arm looked fine. Some grease is coming out of the ball joint, so I am sure it will need replacing. The ball joint, is not causing the play in the steering. When I move the steering from one side to the next, to check play,
Hi Jeff,Play in steering is compounded by each weakness, no matter how slight, that exists in the entire steering linkage. I admire your technique in troubleshooting. You definitely make valid points with your observations. ... 1997 Chevrolet Tahoe
2003 yukon denali driver side mirror and rear view mirrors auto dim won't turn off, passenger side mirror is fine. Any suggestions on how to turn off the auto dim permanently?
... Cars & Trucks
The arm that raises and lowers the window has a track at the bottom of the window it slides in. There is a ball joint that connects the arm and the piece that slides in the track. The ball ball joints popped out of its socket and I can't get them to go back together. Any help would be great! Thank you!
You can buy a replacement in the help section at the autoparts store you drill the rivet out of the old one and bolt on the new one hope this helps ... 2006 Ford Taurus
My 2004 acura tl inside, auto dimming, rear view mirror has mal-functioned and now everything is blurry when viewed through it. i've ordered a replacement mirror thinking i could replace it myself. i'm not sure how to do it, since there is an electrical connection in the overhead console. I'm also not clear on how to remove the existing mirror. Any suggestions?
... 2002 Acura 3.2TL
2000 Buick Regal rear view mirror. Only the center of the auto dim mirror dims now.
I had the same problem. My mirror has map lights so I disconnected the wiring harness from the mirror. I had trouble getting this done, but there is a small clip you must pull back to release the wiring. Once I had the mirror free the button that ... 1998 Buick Regal
My interrior lights, radio, and power side view mirrors suddenly don't work on my 1999 Dodge Neon?! --My car wouldnt start about a week ago so I replaced the battery & starter to find that it still wasn't starting. So I took it to a garage thinking it was an electrical issue. Well, they sent me home with a new starter and it's been starting fine now (knock on wood). But every since they've changed it my power side view mirrors, interior lights, and radio wont work when they were before. HELP?!
I think you can fix this yourself, I just need you to get out the book everyone fears (the owners manual).I want you to go to a section in the book called fuses and relays. Now, in the book, they will have a diagram of the fuse panel with numbers on ... 1999 Dodge Neon
We have a 96 ford taurus had ball joint, front assem, lower ball joints replaced & axle aaem both sides replaced after doing this my husband drived homed it all basically poped off mechanic thinks might have differant trany so I was wondering what differant tranys could bolt up to a 96 ford taurus ( U engine)
What exactly popped off? Did the mechanic state what the transmission had to do with the ball joints? ... Ford Taurus
I broke my rear view mirror off the mount on my 2000 xterra. it looks as if the mirror and arm should just snap back on the ball of the mount. but this is not so. i have tried pushing excessively on the mirror trying to push it back on. but it just wont happen. i even tried heating the arm of the mirror. is it completely broken? and do i need a new one?
I suggest to get a new one you can find a generic one from your local auto part store just unscrew\015\012the little bolt on the base of the mirror and will slay upwards and using the same bottom place the new one or just get one from a salvage Jard ... 1998 GMC Jimmy
2011 Hyundai SE pre wire for Home Link
... Hyundai Sonata
My daughter's 2005 Hyundai Elantra's right side mirror part was stolen from the holder...just leaving a big hole and connection cables. 1. Can I reinstall this myself? 2. Can I purchase just the mirror insert if all th e connections are still there or do I have to purchase the whole right side? 3. How do you install a passenger side view mirror? 4. Is ebay ok to find car parts?
You can buy just the heated mirror with a ring to clip it onto the existing mount,its just a push fit.simply connect the 2 wires and push it in the MIDDLE of the glass to pop it back on.(or you could steal one from another car......yes i know,thats h ... 2005 Hyundai Elantra
Trying to repair a 2007 Subaru Outback. The rear view mirror housing came apart from the base. I detached the base, but cannot get the ball attached to the mirror into the base. How do I re-attach the mirror to the stem?
You dont. they make it so you have to get a new one. my wife broke our in our car and went on e bay and got one for a good price. sorry went through the same thing ... 2007 Subaru Impreza Outback Sport Wagon
The driver's side view mirror glass is disconnected from the power motor mechanism. How do I pop the mirror out and reattached it to the control. The mirror is not broken, just will not adjust with the porer control,
Feel free just pull the nirror out then see if the knob is disconnected or you first check on the fuse that is meant for the power mirror.Good luck.Please rate this ... 2002 Toyota Camry
The passwenger side view mmirror is shattered on my 95 Oddysey. I purchased a factory replacement. The mechanism works fine and I removed the broken glass from the plastic plate that holds the mirror. My problem is that I cannot figure out how to remove the backing and apply the new mirror,which is attached to new plastic backing. How does one attach the new assembly? There is no way to fasten the screw into the pivot joint that moves the mirror, through the glass.
May have to remove the whole mirror assembly to access the backside to reach the screws. ... Honda Prelude
Whenever my car hits the rough road its starts making a sound. In a smooth road it runs like a new car, no sound at all. I am positive that the sound is coming from the bottom part of the steering. The sound is like any rod hitting the other rod but there is something in between the sound is not like "cranck". It could be the joint of the steering and the section joining the two wheels. I have checked all portion of suspension, Link Rod, Tie Rod, Rack End Joint, Ball Joint, Jumping Rod etc. Wher
Have you checked the front struts. have a trusted technician inspect the front end. ... 2004 Toyota Corolla