Having problems with your 2004 Honda Accord ?

I HAVE A CONTINUIG PROBLEM WITH THE CHECK ENGINE LIGHT COMING ON AFTER DRIVING ON THE HIGHWAY----THE CODE IS P0741 (TORQUE CONVERTER CLUTCH SLOENOID VALE STUCK OFF) THE TRANSMISSION WAS REBUILT APPROX 6 MONTHS AGO

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

It should still be under warrenty call the shop, and if it is not try some lucas transmisson oil if the valve is sticking it will help it otherwise take it to a shop and have them check the oil port for the shifing valve.
Repair Help & Product Troubleshooting for 2004 Honda Accord

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A CONTINUIG PROBLEM WITH THE CHECK ENGINE LIGHT COMING ON AFTER DRIVING ON THE HIGHWAY----THE CODE IS P0741 (TORQUE CONVERTER CLUTCH SLOENOID VALE STUCK OFF) THE TRANSMISSION WAS REBUILT APPROX 6 MONTHS AGO


It should still be under warrenty call the shop, and if it is not try some lucas transmisson oil if the valve is sticking it will help it otherwise take it to a shop and have them check the oil port for the shifing valve. ... 2004 Honda Accord

Manual Transmission stuck in gear, car will start and run with clutch depressed but stalls when released. Car will not roll with clutch depressed and brake released. Problem occurred once before about 18 months ago. Had car towed to dealer who said transmission was frozen and they put car in shop and it thawed. Made sense at the time because I had been driving in deep slush the day before. No precipitation yesterday.


Check and confirm the transmission oil.If its low then due to lack of lubrication this can cause.\015\0121. Throwout/Release Bearing failure.2. Internal Cluster Rod malfunction. 3. Lack of proper lubrication. ... 2005 Subaru Legacy

I have a 96 chevy cavalier 2.2l 5spd manual transmission...new clutch 3 months ago...fluid level is full...shifts with no grinding...but when u release the clutch... It takes a minute for it to start pulling... It started whining ...this happens in all gears and rpm ranges...if u rev it high it will engage tranny hard...like it's automatic with a 4000+ stall converter... Any advice would be appreicated


Sounds a lot like the throwout bearing is binding on the input shaft and not releasing the pressure plate. In any case, it needs to come apart to look before anything else gets damaged.. ... Chevrolet Cavalier

I had engine work done and a new clutch installed on my 2002 WRX. About a month after taking the car out of repair, my transmission got stuck in 2nd gear while I was driving. I heard a loud noise and it felt like the engine dropped off the car while I was moving; luckily I didn't get into an accident. The repair shop claims that the new clutch kit they installed has nothing to do with this problem of the transmission being stuck in gear and not budging. I have heard from others that improp


MORE IN FORMATION IS NEEDED TO DIAGNOSE THE PROBLEM . IF THE ENGINE IS SWITCHED OFF CAN THE GEAR SELECTOR LEVER BE MOVED INTO ANOTHER GEAR ? DOES THIS PROBLEM ONLY OCCUR WHILE THE ENGINE IS RUNNING ? I HAVE DON'T BELIEVE THE PROBLEM IS RELATED TO THE ... 2002 Subaru Impreza

I replace the transmission fluid in my 96 b2300 5 spd a couple months ago. We had our first ice storm last week and I noticed a sort of whine coming from the transmission. Not typical transmission whine but more like a pump wearing out. It is loudest at about 1500 -2000 rpm. If I disengage the clutch, the sound goes away immediately and returns again upon reengaging. It is faint at idle with the clutch pedal released but will disappear when depressed. I noticed the clutch fluid reservoir was low


This sounds like you have a deffective clucth release bearing. in order to change it, the transmission will have to be remove. this may have been the result of moisture in the bearing cause by the snow. to avoid such situation again it is advisable t ... 1996 Mazda Pickup

I have 2005 Scion CT, with 5 speed manual transmission. The car has 75,000 miles on it. The problem I started encountering nearly two months ago is that when shifung into 5th gear overdrive, the transmission grinds. I have changed out transmission fluid to Redline Oil 75W90 when I had approximately 50,000 miles on it. So far I have not replaced any of clutch assembly or associated parts. Such as throwout bearing and pilot bearing. My clutch does not slip and my free travel/play is still within t


I had the same problem.. About a year of that problem i lost 5th gear and i had to replace my transmission. ... 2005 Scion tC

Hi Experts, 2002 DeVille, love it and need to keep it running. Codes P1860 Torque Converter Clutch PWM Solenoid Circuit-P0741 Torque Converter Clutch System stuck. Torque converter solenoid pwm (drawing 12 amps-should be 1 amp) Disconected solenoid for present time. Shop says they have to drop the engine / transmission to replace the solenoid. Small leak from oil pan gasket which they say cannot be fixed without dropping the engine as well (do both together) Anyway round this very expensive fix


II do not believe the shop is being very honest with you, I'm inserted my substantial comments in the comments portion of this email. Feel free to take a look at them ... 2002 Cadillac Deville

My 1991 manual transmission toyota camry won't disengage completely. Same thing happened about a month ago one day and then seemed OK for about 500 miles or so and now is doing the same thing only this time it won't stop. If I start it with the clutch pedal to the floor, it tries to move slightly meaning the clutch is not disingaging fully. I replaced the clutch master cylinder about a year ago but have not seen whether slave or linkage is operating normal or not (have no help to watch or push i


Definetly your slave cylinder. Seen it several times on toyotas in my career. I do suggest buying a new slave cylinder rather than trying a rebuild kit. I've had customers that requested a simple rebuild kit in the past, and had them fail within a fe ... 1994 Toyota Camry

I have a 99 ford F550, and have replaced the clutch on it 3 times in the last 5 months. I do not understand why it keeps going out. This issue has been very frustrating and expensive. Is there an underlying problem that I am not seeing? I had the transmission replaced by ford 2 months ago, got a new rear end and a remanufactured 7.3 motor from ford as well. With all these new components, I do not understand why I keeep having these clutch issues.


... 1999 Ford Super Duty F 550

Transmission slipping I have a 96 dodge ram 1500. 5.2 v-8, auto transmission. approx 105k miles. I changed my radiator a few months ago, and in the past two months my trans has been slipping. If I step on the gas from a dead stop it shifts fine, but if I start off slow it slips all the way up to top gear. I can get it to shift by working the accelerator when it is slipping. Any suggestions?


Did you check the trans oil level. When you changed\015\012the RADIATOR you will loose some trans oil.\015\012If the transmission oil was low when you changed\015\012the radiator it's lower now. Check it now.\015\012Now, if th ... 1998 Dodge Ram 1500 4WD

Clutch issues new clutch and transmission over haul 17 months ago.. 1999 pathfinder SE.. clutch makes a grinding noise occasionally when going in.. did it before the new clutch, went away after and now has returned


Sounds like it could be time for another clutch, I would make sure that the pressure plate and throw out bearing gets changed as well. And try and use a quality clutch kit because a clutch should last a lot longer than that with proper driving styles ... 1989 Nissan Pathfinder

Transmission 6 months ago I had my transmission on my 1989 Ford F150 Pickup rebuilt. Now it is time to put in transmission fluid. The converter is also empty. What is the proper way to add the transmission fluid?


If it is an automatic the best thing to use is chrysler automatic trans fluid Most 1998 Ford F150s take Mercon V...also check for leak. The transmission dipstick is located on the passengers side rear. Near the firewall / or back of the engine. The d ... 2000 Cadillac Catera

I have a 1995 Isuzu Rodeo, 4-wheel drive, 3.2L V-6. A new clutch was installed in 2006. A few months ago, my wife was driving it up up a steep grade. There was one short screeching noise from somewhere around the transmission / clutch area and then the car would not go into gear. So we coasted to the side of the road where we noticed some smoke with a sweet antifreeze smell. So now, if you hold down the clutch pedal, you can start the car. But you can't shift it into gear. And


... 1995 Isuzu Rodeo

I have a 2000 saturn SL2 1.9L DOHC automatic trans, the transmission recently failed so I replaced the transmission, the transmission has approx. 34,000mi. After installing trans I got a code 741 TCC stuck in off position. I replaced TCC solenoid, still the same so pull the trans back out and replaced torque converter, still the same, I also set the transmisson range switch again to double check.


... 2000 Saturn SL

5 months ago I got the Check Engine light on my 2001 Cadilac Deville. When the diagnostic tester was used they got a code P0741. I had the transmission overhauled and now 5 months later I have the same problem with the code P0741. The mechanic performed the same fix a second time including the converter, the TCC and solenoid and still the problem persists. What can we do now??


It hard to get a solution unless u use a tech ll that runs a data stream-just a code can means different things--dont know how well its been rebilt but accumulator springs are common in older trans as well as governor pressure switches--some trans re ... Cadillac DeVille

I have a 91 Chevy silverado with a 700r4 transmission that has been shifting hard and late for a few months. Over the choose of a few days it began getting worse until it wouldn't shift at all (like in neutral.) Upon inspection the fluid was black and smelled burnt and the clutches were destroyed. Replaced the clutches, filter, fluid, and torque converter. The pump looked fine. Now with it installed I still have no pressure at the oil cooler lines and still will not go into any gear. Torque conv


Were the lines flushed before reinstallation? If not, old clutch material may be blocking the lines, or buggering up the pump. ... Cars & Trucks

1993 Renault 19 - transmission warning light comes on and car stuck in 1st gear. Sometimes when the car has been running a while and warmed up, I turn off the ignition then turn it on again and the light disappears but lately it just stays stuck in 1st. Oil levels are OK. 18 months ago had similar problem which was fixed by installation of a new solenoid pack at huge expense, could this be the problem AGAIN?


Unfortunately, each transmission has its weak link,......something which the manufacturer overlooked at being an overstressed component......and with the renault transmissions, the solenoid was it.\015\012When the light disappeared, this was th ... 2000 Renault 181

I bought a used 2004 Volvo XC90 T5, auto transmission a year ago. I am having having the following problems: 1. Anti-skid service required message - what does this mean? 2. Cruise control will not engage 3. Gear shifter gets stuck in Park and will not shift to another gear. If I wait for about a minute or longer it will eventually shift out of Park. This started a few months ago and was occasional, not it is EVERY time. 4. Stereo system - radio volume randomly adjusts from really


1. Anti-skid = ABS. This means that there's something wrong with your brakes which is a very serious problem, take care of it immediately.\012\012\0122. that can be caused by a lot of problems, but the most common one is a bad servo which must ... 2006 Volvo XC90

About a month ago I began hearing rattling noises when I would depress the clutch. Over a few days the noise became less noticeable but then I started having trouble shifting gears (5 speed manual transmission ford ranger 2002). It was first diagnosed as a leaky master cylinder and that was fixed. The truck drove fine for a couple of days and then the difficulty returned to the point where I could not drive the truck at all. Then it was diagnosed as the input shaft, that was a week ago. Today


If the bearings were worn out due to high milage, the input shaft will have too much play in it. To replace all of the bearings is a big job, and a lot of shops won't do it. They may have replaced the transmission to save time, as replacing the beari ... 2002 Ford Ranger Regular Cab

My transmission is shifting late. it will not shift out of first gear until i have reached 35mph. thw same with 2nd gear. not until 6omph. i first thought it was stuck in 4 wheel drive. checked the transmission and is in 2 wheel drive. fluid levelis good, with clean fluid. i had serviced the tranny wen i got the vehicle 3 months ago, with new filter and fluids. the first thing that comes to my mind is the tps. what else might it be?????


On the side of the transmission you will see the selector shaft for the shifter cable and a smaller arm that goes to the throttle valve. It is most likely seized keeping the transmission in passing gear. A little penetrating oil and move it back and ... 1989 Jeep Cherokee

My kia sephia..the gears are slipping in 3rd all the way to 5th when I push the gas pedal down ...I have a 5-speed 4 cylinder..The plugs were changed less than three months ago..Why is the transmission slipping. Do I need a new transmission or is it the clutch?


You need a new clutch. A 5 speed is a gear box , they dont slip like an automatic can. ... 1995 Kia Sephia

Hello. My 2001 PT cruiser with manual transmission keeps stalling..it doesn't Idol without stalling .About a month ago I had a new clutch installed but everything was fine until now.What is normal idol rpm for the car?it's almost like I wish I could turn a screw just like older vehicles to bring up the idol.when my foot is on the gas in neutral, I can maintain idol but once I let off it just stalls.. Can someone please help me troubleshoot my problem.. Thank y


Sounds like the automatic idle speed motor has gone bad and needs replaced ... 2001 Chrysler PT Cruiser

I have a 1997 Concorde, with a 3.5 L engine and auto transmission. Has approx. 95,000 mi. About a month ago I started the engine backed up 30' and put it in drive and had no movement. Shifted back to reverse and nothing. Shifted through all gears and park and nothing. After about 45 secs. of shifting I finally got it to go. I have driven it about 1000 mi since then with no problems until this morning. I again backed up a couple of feet and put it in drive and had nothing. I shifted through the


The mystery of Chrysler transmissions...if fluid levels are good, make certain you have good electrical connections, especially grounds-your electric system is good, I assume-12.5 + volts resting, 14+ volts running at the battery AND the back large p ... 1997 Chrysler Concorde

I own a 1995 Saab 900 SE turbo with a manual transmission. The car is maintained by a Saab certified mechanic who owns his own shop. The previously worked for Saab directly. When I shift now, the car does this strange bucking and the tachometer drops immediately. The car was in for maintenance about 3 months ago. Then, I had to replace the exhaust system because it sounded like truck. Then the reverse gear went out. The car had a failure prior to that and the mechanic replaced the clutch c


... Saab 900

My sister has a 1998 Audi A4 (automatic transmission). She tells me that there is a acceleration problem. The engine will rev to the moon then all of a sudden the gear will catch and away she goes. I was thinking the problem was either the torque converter of the tranny itself. Havent checked the fluid, however i can only imagine that its still at proper level and condition due to an engine swap a few months ago. Maybe a pressure problem to the servos? what do you think?


SOUND LIKE TRANSMISSION SLIPPING. CHECK TRANSMISSION FLUID LEVEL.IF FLUID LEVEL OKAY BUT FLUID LOOKS DARK SMELL BURNT.CHANGE TRANSMISSION FLUID AND FILTER ADD SOME VALVE BODY TREATMENT TO LOOSEN STICKEN SHIFT VALVES.ADD TO TRANSMISSION FLUID DONT OV ... Audi A4
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2971 seconds