Having problems with your 2004 Chevrolet TrailBlazer ?

Cam position sensor bank 1

\015 Does anyone know where the cam position sensor bank 1 is located on a trailblazer I6?\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Cam sensor is in the cylinder head next to number 1 cylinder.
Repair Help & Product Troubleshooting for 2004 Chevrolet TrailBlazer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2003 cadillac cts 3.2 liter..rough idle, scan tool shows misfire on bank 1, cylinders 1,3,&5. only at idle, scan tool also showed a cam postion sensor code. cam position sensor changed. no change in idle. clyinder compression test, and cylinder leakdown test performed on all cylinders in that bank. all cylinders in both tests were within specifications. spark plugs replaced on that bank. On road test vehicle has lots of power and acceleration. problem only accurs at idle. any suggestions would


Did you ever find a solution to this? I am having the same issue on 2,4,6. I have replaced the coils. checked the intake for vacuum leaks. I am lost here let me know if you find anything and I will do the same. ... 2003 Cadillac CTS

2003 Beetle turbo-13 trouble codes-PO300-multiple cyl misfire-PO171-system lean, bank one, PO301, PO303, PO302,PO 304-cyl one thru four misfire, P0012-intake cam position timing over-retarded-bank one, PO333-knock sensor curcuit high input-bank #2, PO328-knock sensor 1 bank one-curcuit high input, PO721-output speed sensor curcuit range/performance, PO731, PO734, PO 729 all trans incorrect gear ratio codes. Unit runs but exhausts back into the intake after 10-15 seconds after start up. All this


Low fuel pressure will cause many of those codes to set.Should have around 3.5bar pressure at idle and full throttle.Check to see if VW has a recall on the ignition coils. They are cheap to replace however.....you will need yo ... 2002 Volkswagen Beetle Turbo S

SL2 Won't start; previous codes=PO 133 + PO341 + po420; REPLACED O2 sENSOR - Bank 1 Camshaft Position Sensor Apparently is OK; Resistance=Approx 800 ohms & Output >600 mv; Can't locate Cam position sensor; Think it is near oil filter and has only one wire, but not sure of wire color or sensor resistance or output. Fuel pump relay seems OK; Switched relay with identical one. Fuel pump spins, but didn't measure pressure. Also changed plugs & wires previously & it ran then. WHAT'S


I HAVE A 98 SATURN, WON'T EVEN TRY TO START EVERY ONCE IN A WHILE. TURNS OUT TO BE THE CRANKSHAFT POSITION SENSOR ... 1999 Saturn SL

Mil ligth on trouble code P1345 vvt sensor/camshaft position sensor circuit(bank 1).I replaced cam position sensor, light come on after driving for a while , which sensor control the vvt actuator


... 2003 Toyota Corolla

MIL ligth on, trouble code P1345 VVT sensor/camshat position sensor circuit (bank 1). I replaced cam position sensor the MIL comes on after driving for a while. 4ZZE-FE Toyota corola engine


... 2005 Toyota Corolla

My engine light came on my 07 Acadia. I had someone run a diagnostic test and it gave me possible problems. 1.)Timing Misalignment with explanation crank sensor is not aligned with cam sensor. 2.)Crankshaft position(ckp) vs. intake camshaft position(cmp) correlation bank 2 fault. with explanation the ecm has detected the the actual cmp angle of one camshaft is greater or less that the commanded state how do i fix this?


There is a bulletin (or recall depending on your mileage) for this issue. The timing chain stretches due to lack of oil lubrication. The acadia engine is very sensitive to timing chain stretch. There are 2 things they will do. The first is a repr ... 2007 GMC Acadia SLE

I put a monitor on the the car. it came up eva p0016 stating a crank position correlation problem camshaft position bank sensor A. should i replace the cam shaft postion sensor and/or the crank shaft?


... 2006 Hyundai Tucson

Cam position sensor bank 1


Cam sensor is in the cylinder head next to number 1 cylinder. ... 2004 Chevrolet TrailBlazer

Cam position sensor, B Bank, Circuit 2, High Input


... 2007 Toyota Tundra

Where is the cam position sensor bank 2 located for my 2004 nissan quest


... 2004 Nissan Quest

Put a motor in my '97 toyota camry LE 2.2 4cyl. runs good but has check engine light on and the code reads: cam position sensor.. A Bank 1 circuit malfunction...does this mean sensor is bad? or could it be something else? thanks


02 sensor is defective... if the cam sensor did not work it would not run, try replaceing the 02 SENSOR... ... 1997 Toyota Camry

2000 Mitsubishi galant 2.4L car starts fine cold! If I drive it than turn it off it will start than die. I had two codes cam shaft position sensor and a o2 sensor second bank. Things I have replaced s


Do you have fuel pressure at the motor? ... Cars & Trucks

Where is Bank 2 located on a 2004 Nissan Maxima?? My cam Shaft position sensor went out in bank 2


Sending a picture ... Cars & Trucks

I have 2008 Dodge Caliber and the engine light came on with codes P0017 Crank Shaft Position Cam Shaft Position Correlation - Bank 1 Sensor B can you tell me what this means as i cannot afford to pay $100.00 for a dealership to run their test just to tell me what is wrong?


Sounds like your crank sensor or cam sensor is malfunctioning. Their positions are not correlating which means they are not in perfect alignment according to the computer. I don't think the parts are very expensive and probably not that hard to repla ... Dodge Caliber

I had replaced my 4 o2 sensor on my suv after used OBD to reset the board to turn off my checke eng. light came back on. I replaced o2 sensor by universal type of o2 sensor.I got this message on the OBD: 1)p22392 o2 sensor positive current control circuit high bank 1 sensor 1. 2)p2242 o2 sensor positive current control circuit high bank 2 sensor 1. 3) p2252 o2 sensor negative current control circuit low bank 1 sensor 1. 4)p2255 o2 sensor negative current control circuit low bank 2 sensor 1


... 2003 Toyota 4Runner

I replaced the engine in my 2000 dodge intrepid 2.7 engine. Would not start with my cam position sensor connected. I unhooked the cam position sensor and the car started put ran at 2500 RPM. Replaced cam position sensor. The car still would not start until I unhook the cam position sensor.Is their anything else I can check?


You need to verify the magnet in the engine is stll intact. Also you need to graph the sensor for a steady pulse. Search how to test a Cam and Crank sensor.. Also you should have a code stored for the no start condition. This will tell you what se ... Dodge Intrepid

Car was running well then just refused to start.Computer indicated throttle position sensor. Replaced that, then crank sensor, then cam position sensor. Then took car to a repair shop. They thought cam belt, all looked good. They then said wire to crank position sensor bad and replaced it. Car then started with miss fire. The repair shop then replaced all plug wires and plugs. car still miss fires, they then replaced the coil pack.Car still miss fires on passenger side cylinders. The car starts


Its possible there are multiple coil packs usually one for each bank or one for every two cylinders. Or check for a ignition control module ... 2004 Dodge Intrepid

Jeep stalls, runs rough after cam sensor replaced. 2002 Jeep wrangler 4.0 X manual trans. Replaced shear pin on cam sensor. When cam resensor was installed the vehicle would not start which was accomplished by turning the sensor about 45 degrees from its original position. It ran fine for 12-14 miles then completely died. I turned the key off and it would restat, run fine for a while, then die again. Noo timing to set, fuel filter to replace. did I place the gear on the sensor in the wrong posit


... 2002 Jeep Wrangler

Hyundai sonata cam position sensor bank 1 location


... Cars & Trucks

Where is the bank one cam position sensor on 2004 nissan quest


... 2004 Nissan Quest

2006 chevrolet hhr cam position sensor a curcuit range/performance c bank 1 or single, code P0341


... 2006 Chevrolet HHR

I have a 2001 vw Jetta glx 2.8 liter v6 engine and need to replace the cam position sensor on bank one. I do not know where it is located on the engine can you tell me where it is located?


I think there is only one, its behind one of the cam sprockets ... 2001 Volkswagen Jetta TDI

I have an A4 quatro with a 3.0 the people at auto zone said the cam position sensor A bank 1 is bad. is that the ehaust or intake


All the oxygen sensors are mounted on the exhaust system. Bank A /one basically means the sensor before the catalytic converter. Bank one usually refers to the left-side of the vehicle if you are facing the vehicle in the ho ... Audi A4

POP340 cam position sensor a bank


... 1998 Chevrolet Tahoe

My 2002 Audi A6 is throwing two codes. P0300 and P0341. Random Misfire and Bank 1 Sensor A Camshaft Position Sensor. If it isn't the position sensor that's the issue, what could the issue be? Could my timing have skipped on the Bank 1 side? I just purchased the vehicle. Shortly before purchase, the previous owner had the passenger side tensioner replaced. Could this have been installed incorrectly, throwing off the timing on that bank? Thanks in advance for the help. Jeff


... Audi A6
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.3863 seconds