Having problems with your 2004 Chevrolet Silverado 2500HD ?

2004 chevy 2500 hd diesel will not crank, i have power to the crank fuse under hood in fuse panel when trying to start, the starter relay also has ignition power to it but it does not get its signal to close relay, if i give signal it will close and crank. We had starting problem 2 times before this issue but starter was engaging and turning slow load test both batteries they were weak we replaced them truck started up fine. Then we were trying to check and clear check engine light when our curr

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2004 Chevrolet Silverado 2500HD

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2004 chevy 2500 hd diesel will not crank, i have power to the crank fuse under hood in fuse panel when trying to start, the starter relay also has ignition power to it but it does not get its signal to close relay, if i give signal it will close and crank. We had starting problem 2 times before this issue but starter was engaging and turning slow load test both batteries they were weak we replaced them truck started up fine. Then we were trying to check and clear check engine light when our curr


... 2004 Chevrolet Silverado 2500HD

I replaced the starter motor. Now when I try to start it, it won't do nothing. No crank no start. Even the dashboard has no signal. Battery checks out and cables okay.. Is it the starter relay? Where is the starter relay location? Regards Ernst Gfeller Garden City, MI


The starter relay is usually attached to the starter, this is where the cables are connected to.\015\012If the dash has no power, there is either a wire not back in place , or it may have tripped a breaker on the positive cable if it has one. ... 2000 Ford Taurus

My 2000 lincoln ls doesn't crank or click when trying to start it, it does nothing? all the lights work, radio, signals and horn, I checked the fuel relay and the starter relay and the ignition fu


Sounds like an Ignition Module or similar device. Does it have an alarm? Turn the key to ON - not start - and put into Drive and then back into Park. It may be the shifter isn't fully engaged. Also, w/your FOOT ON THE BRAKE shift to Neutral and try t ... 2000 Lincoln LS

Fcm front I have a 2005 Chrysler 300 unit will not crank I checked relays found ok if I jump the starter relay unit will crank but won't start with key on the run position checked signal from ignition switch to starter relay and there is none, those the Fcm control this signal or those the ECM control it?


... 2005 Chrysler 300

2000 olds drove to work fine this morning this afternoon it would not CRANK, just a load starter/solenoid click. changed starter this afternoon, still same load click, checked battery volts 12.6 , cleaned terminals and tried jumping...same starter click. engine is not froze, ran wire to starter from battery ground, no change in click. checked fuses and relays (swapped crank relay with cooling relay) no change. Instrument panel lights up like a xmas tree, speedo and tack gages go are pegged wh


This might noy be of much help, buy I would try a remote starter switch hooked up to the starter,with the ignition switch in the run position..then push the remote start switch.\015\012This would give you an idea if the ignition switch is a par ... 2000 Oldsmobile Intrigue

2000 Olds intrigue problem with intermittent starter cranking... Checked relay in the fuse/relay panel that feeds the starter solenoid and the signal is intermittent getting to the relay from elsewhere in the car. Looking for a diagram to tell what wires to check inside the car - ignition and transmission switches that pass the start voltage.


... 2000 Oldsmobile Intrigue

1996 Ford E250 van. I checked to see why the horn wouldn't work and found the problem is in the horn switch. Went to start the van and it won't start. I was able to start the van via the fender mounted starter relay by using a screw driver on the two posts. Bought a new started relay and still won't start. Tried to start it in Park and Neutral and still no crank. So I have a no start no crank situation. There is power to the relay. What am I missing here? Thank you


Hello, my name is Ben. When you started the van using the fender mounted relay, you were basically bypassing the key switch. I'm thinking you might have accidentally disconnected a wire during your repair of the horn switch. Or it could just be a coi ... Ford E-250

CHEVY COLBOLT 2005 CHEVY COLBOLT WILL CRANK BUT WON'T START. I CHANGED FUEL FILTER I CHECKED THE FUSES AND I CHECKED TO MAKE SURE THE STARTER IS GOOD AND THAT THE SPARK PLUGS ARE SPARKING. I DO SMELL GAS. I TRIED TO SPRAY STARTING FLUID AND IT WOULD NOT START. IS THERE A FUEL RELAY SWITCH OR IS THAT JUST A FUSE.COULD IT BE THE CRANK OR TIMING OR DO YOU HAVE ANY SOLUTIONS. THANKS


Listen for fuel pump when u turn key to on [not start] should hear a hum-check for pressure at fuel port -if pressure need to start checking sensors a bad crankcase position sensor--camshaft position sensor --bad egr valve--can shut down and not allo ... Cars & Trucks

S10 1999 bearings bad 0 oil pressure,removed and rebuilt engine, replaced most all. back in and...Won't start, not a crank or a ticking from the starter. Starter and starter selanoid, battery all tested OK.conecting to starter and starter getting power. Replaced neutral safety switch twice , check all 3 relays all OK. Still no response. Lights and accessory lights all go on when ignition turned. Have tried all gears but still nothing. Could I have forgotten to replace something. Is there a way t


Yes, you can hotwire the starter, use a button starter to energize the solenoid. there is a chance thet the new or rebuilt starter isn't working. it has happened to me I went an bought a newly rebuilt starter but it was no good, it happens sometimes. ... 1999 Chevrolet S-10 Pickup

My daugther has a 2003 Grand Am and will not start. Have check the starter and the alt,check fuses and relays. Fuel pump is working check battery cables and safety switch and some of the wiring.Now we are leaning toward the computer. This is what it does when try to start it.Turn the ignition on and get all of the dash lights and all of the normonal stuff that is suppose to come on.Turn the key to start and nothing. There is no noise at all no slow crank no clicking nothing. So here is the ? Any


Okey i am sure you have a test light . jack the front and make sure it is secure. connect your test light to good ground and touch the smallest cable on the starter and make some one crank the engine if you got light while some one try to crank some ... 2000 Pontiac Grand Am GT

1997 cavalier 2.2 new battery ,plugs wires,coil pack ,clean con on batt.,and starter,had starter checked twice..it would only make one click then no crank.put a new relay in,it tries to crank ,kinda week.no start.dont want to kill battery.


Vicario123 is correct I have the same car the relay by the radiator was bad not allowing any power to the coil, injectors or plugs leading you to think the switch was bad but it is just the relay ... 1997 Chevrolet Cavalier

I have a 1994 nissan sentra 5 speed that won't start. When i put the key in the ignition to crank i get nothing, no clicking of the starter, no sound of the fuel pump priming itself or anything. I do have power to the lights, instrument panel and all flashers and turn signals work but no radio so far. I've checked the fuses all are fine in the engine bay and on the inside compartment. I think it might be a relay problem and would like to know if it is ''where are the right relays that i need to


I know this sounds ridiculous, but if you just bought this car with it not running and you have never owned a 5-speed, push the clutch in to start it. On most cars, the list and location of relays are on the inside of the fuse/relay cover. If it's ... 1994 Nissan Sentra 4-Door

Won't start. Just cranks over and over. Checked spark on coil, works. Put a little gas down intake, tries to kick over. So I know that it isn't getting fuel. So I also checked fuel relay by swapping out with the others that worked. Still no start. Checked all fuses, all fuses are good. It does have a remote start on it, so tried with it, and it does same thing, just cranks. Out of ideas. Summary of when it started. Just died pulling into parking lot, tried cranking stayed started, but


Check the fuel pressure. ... 1994 Dodge Dakota Club Cab

Will not crank over when you turn the ignition key. It will crank if you jump over the starter manually. when you turn the ignition key it clicks once like a relay is kicking on and off but the starter will not do anything at all. I pulled the cover off of the starter relay and the relay stays closed at all times when the key is in the ignition. I swapped it with another relay and it does the same thing.


,,,,, if u get the signal at the siloniod, then u either have a bad siloniod or a very bad ground to the stater,, try starting in nutral,, make is its not the nutral safty switch turn aon all your lights and see if when u try to start the car that th ... 1997 Chevrolet Venture

2003 Ford Windstar - no crank/start problem. Our 03 will not crank on cool (65 degrees and lower) mornings but will start later in the day when it is warmer, Have changed - alternator, starter, ignition switch (electrical), TPS (aka - neutral safety switch), battery and changed out several relay and fuses. Checked ground in three places - clean and secure. This a.m. mechanic tried to read codes - only thing coding was that the key was not being recognized - yet it would and does start on oc


... 2003 Ford Windstar

My 2000 eb expedition wont start. tried starter fluid it will crank over but wont stay running. ive checked the fuses and relay gut nothing. im not hearing the fuel pump run or anything


Nest step is to dicconnect harness at fuel pump and check for voltage there, if so then pump is faulty if not look for fuel pump reset location found in owners manual ... 2000 Ford Expedition

Kia Pregio 2.8l Diesel The "hand Brake" light turns ON, while the "Charge" light turns On as well, Engine wont kick to start. Causing the 1)engine starter 2) Alternator to short circuit. Initial trying to start up, engine continuously cranking even the key pulled out. Checked the main fuse 80A blown. replaced the fuse and things looks normal. But there's no charge' signal available on the meter board like usual, whenever the key turns to ON position. Normally in this condition, the 'Oil Pre


... Kia Sorento

I went out to warm it up,it started fine.When I came out to leave,it was dead.All of the instrument cluster lights were on but it wouldnt crank and i am not getting a fuel pump.I checked the battery,all of the fuses and relays.I replaced the ignition switch,still nothing.Ichecked for power at the starter relay,fuel pump relay and ASD relay.I have power to all of them on 2 pins.I even have power to the yellow start wire on the starter relay when I turn the key to start.Im not getting any crank or


First unhook the battery for about a half hour to reset the computer.\015\012does that have anti-theft on it.\015\012a remote starter ?\015\012second either swap the relays for the starter and fuel pump or replace them outright. ... Chrysler PT Cruiser

Hi I have problem with Chrysler Voyager 2001 3.3l Automatic.The car would turn over from the key,I have checked the ign switch-sends a signal to the starter relay.The PNDR switch is operating,the wiring from starter relay to ecu is good.there seems to be a signal missing suppling negative to starter relay from ecu.This is my problem.Any surgestions?


Pin 86 and pin 30 at the relay should have power then your right about ground supplied from the ecu and the other goes to the starter solenoid check for battery voltage on those 2 pins 86 and 30 one fuse is under the hood and the other is under the d ... 2000 Chrysler Grand Voyager

Starter relay when i turn the key the starter on my 2005 nissan titan makes a clicking sound. The battery is fully charged. Dashboard lights up and all beeps & alarms sound off. Before I try to replace the starter I would like to try checking all of the electrical parts..ie..fuses...relay..etc. I can't find any diagrams to show me where everything is. Does anyone know where these are located?


... Cars & Trucks

I have 1997 Toyota T100 that cranks and dies.It cranks and run for 1 to 2 seconds and dies.It keep doing it when I try to start the vehicle.I check fuel pressure,it has pressure 45 psi when cranking,it has spark also.I check fuel pump relay pin that goes to PCM for ground signal.I check with voltmeter and the PCM gives ground to the pump relay.What else that I can check ? I need help.Thank you for your attention.


If an engine cranks but refuses to start, it lacks ignition, fuel or compression. Was it running fine but quit suddenly? The most likely causes here would be a failed fuel pump, ignition module or broken overhead cam timing belt. Has the engine been ... 1996 Toyota T100

1998 jeep grand Cherokee Laredo 4.0 no start her starter relay clicking but nothing checked starter and ok swaped starter relay and nothing tried jumping off nothing just relay clicking not starter getting ready to change ignition switch.


... 1998 Jeep Grand Cherokee

I have a 2003 GMC Yukon Denai XL.. I crank it up this morning because it was cold outside (it crank fine) I left it ruuning and went back inside, when I return (about ten minues later), it had shut down... When I tried to restart it, it wouldn't make a sound... the light on the dash comes on, but no sound. I checked the battery (tried to jump it off) checked all fuses and relays.... The fuel pump doesn't make the whnnng sound, the started doesn't turn over (nothing)... no codes !!! I noticed tha


If the starter does not engage,remove the cables from the battery,and clean them real good,it may have a bad connection,or the battery is so bad,it may have shorted out,and you need a new one,have the battery checked,if the battery is real bad,someti ... 2003 GMC Yukon Denali

I have a 2002 VW Jetta. 2.0L automatic. When I try starting it, all of the dash lights come on as usual but it will not turn over. I checked the fuses, good. Checked the battery, good. Tried jumping it, nothing. Replaced the ignition switch, starter relay and starter. Still the same thing. Lights come on but will not turn over. Any suggestions would be greatly appreciated!


Http://www.autozone.com/autozone/repairinfo/re ... Cars & Trucks

I have a 2003 GMC Yukon Denai XL.. I crank it up this morning because it was cold outside (it crank fine) I left it ruuning and went back inside, when I return (about ten minues later), it had shut down... When I tried to restart it, it wouldn't make a sound... the light on the dash comes on, but no sound. I checked the battery (tried to jump it off) checked all fuses and relays.... The fuel pump doesn't make the whnnng sound, the started doesn't turn over (nothing)... no codes !!! I noticed tha


You are going to have to make sure the battery is completely charged.If you have to take it out to get it checked and load tested.I would have the complete charging and starting system load tested also.The other thing is sometimes these gauges,especi ... 2003 GMC Yukon Denali
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.6475 seconds