Having problems with your 2004 Chevrolet Silverado ?

Blower motor the blower motor does not work ive changed the blower fluz 2 times alreadt and ive looked around but im not sure where the motor is located at i think its mounded on the firewall with the brake cylinder mounted on toip of it so if you can give me any ide's it would help also the heater fuze is ok

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

PART 1
\015\012If all blower speeds are not working I would check the blower, but if only one speed is not working I would check the resistor block for the blower it controls the speeds. they use 2 different blowers in this truck I have to sent a second message with the rest it will not hold it all inthis message.
\015\012
\015\0122001–05 Models With Delphi Blower Motor
\015\012
    \015\012
  1. If equipped, remove the sound insulator panel. \015\012
  2. Remove the blower motor insulating cover screws. \015\012
  3. Disconnect the electrical connector from the blower motor. \015\012
  4. Remove the blower motor insulating cover. \015\012
  5. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor from the heater/ventilation module. \015\012
  6. Remove the blower motor.
\015\012 c93043c.jpgPull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor
\015\012
\015\012To install:
\015\012
    \015\012
  1. Install the blower motor. \015\012
  2. Install the blower motor to the heater/ventilation module. Turn the blower assembly clockwise until the retaining tab locks into place. \015\012
  3. Install the blower motor insulating cover. \015\012
  4. Connect the electrical connector to the blower motor. \015\012
  5. Install the blower motor insulating cover screws. \015\012
      \015\012
    1. Tighten the screws to 14 inch lbs. (1.6 Nm).
    \015\012
  6. If equipped, install the sound insulator panel
Repair Help & Product Troubleshooting for 2004 Chevrolet Silverado

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Blower motor the blower motor does not work ive changed the blower fluz 2 times alreadt and ive looked around but im not sure where the motor is located at i think its mounded on the firewall with the brake cylinder mounted on toip of it so if you can give me any ide's it would help also the heater fuze is ok


PART 1\015\012If all blower speeds are not working I would check the blower, but if only one speed is not working I would check the resistor block for the blower it controls the speeds. they use 2 different blowers in this tr ... 2004 Chevrolet Silverado

I have a 2001 Chevy Malibu LS 6-cylinder and my heater blower stopped working. I checked the fuses and they are all good, I assume the motor for the blower is bad. I believe the blower is a 1997 - 2003 Chevrolet Malibu 4-Seasons A/C Blower Motor. Do you have any other ideas? Also, where is the heater blower motor located? Do you have instructions to put this unit in? Please advise. [email protected]


Replace the blower motor resistor. Remove the shroud below glove box, 2 screws and a snap-pop fitting. Be careful of the courtesy light. Remove the blower moter and disconnect the purple/black power connector to it - - you'll need this extra room ... Chevrolet Malibu

Replaced blower motor and capacitor on AC-Furnace. 3/4hp, 4-speed, 115V. Ran for 6weeks, now stopped; blew circuit breaker. When powered in the system, motor humms, and maybe gives a little rocking motion. Motor & blower wheel spin freely. Replaced capacitor. Any thing else before I replace the motor? Can't be bad motor after 6 weeks???


1. check voltage at motor, maybe not enough supply current check connections at both end, one for the wires could be loose, at the breaker also.2. check the filter maybe very dirty or someone forgot to take off the plastic wrap.3. d ... 1991 Buick Park Avenue

1993 chevy corsica i have a broken (motor mount?) look's like a dog bone evry where ive looked for motor mount the pics are only of the mounts on top of the engine this one is on the bottom can you help me out with what its called?


Lower engine mount or (dogbone) ... 1993 Chevrolet Corsica

I have a 2000 chevy impala and need to replace the heater/air blower motor. The problem that I have is that the wiring harness is just the blow motor mount. There is not enough slack in the harness to drop the motor and mount straight down. What advice might you gave me? Thanks for your reply. ADS


Be brutefull and try to break some of the plastic clips holding the wiring ,try cutting them first though ... 2001 Chevrolet Malibu

I got a 1995 s420 blower blows good then slows down almost to a stop , ive replaced the resistor it worked for like 2 min. blew hard then i think the blowermotor resistor burned out and completely stop working i put back the original one and it blow for like 30 seconds and then slows down almost to a stop i checked the resistor and it gets suppppper hot i cant even touch it i think the blower motor is bad what u think i jumped the blower motor direct and the wires get real hot i think the blowe


I would agree. If you wire it direct the wires should not get hot.The resistor will get hot under normal conditions because the resistance is how the motor speed is controlled.So you are probably right the motor is failing.You could get ... Mercedes-Benz S500

Ok, may sound like a dumb question,but how do you know if its a blower motor resistor problem or just the blower/motor. Ive been reading solutions for problem on the A/C blower still blowing air but speeds off or that the blower works sometimes and sometimes not. If my A/C doesnt blow air at all, do I just replace the motor or resistor? --Sonia


The blower motor resistor is usually only switched into the circuit for the lower speeds and for the fastest speed the resistor is bypassed so I guess the motor needs to be replaced if it does not work in any position. However, sometimes the blower m ... 2006 Nissan Altima

The blower fan only works on high setting, and the acwont work or it doesnt come on . ive chrcked all fuses and they are good.also during the summer alot of condesation water come into the car from the fans location and it filled the blower motor up with water. then it all stopped working. but now the motor does run on high but no other speeeds and the ac is out , any ideas?


Motor may be shorting out because of the water that got in it ... 2003 Mitsubishi Lancer

Put van in shop for map sensor change. said they checked van ou and i needed a motor mount replaced, 2 plug wires in back of engine and throttle body cleansing. they did that. said to give them another day, because van running rough after fix. called said i now need head gasket replaced..i think they damaged it when they changed the motor mount. i had no over heating, no smoke from the exhaust, no water drops from tail pipe, no milky oil . no leaks of any kind


I don't imagine hey could damage the head from changing a motor mount. However you have reason to have caution; why suddenly does it need a a head gasket? What reason is give? (is there old leakage they can point out?) Your correct about the oil and ... 1996 Plymouth Grand Voyager

Blower motor when i turn on my car the heater wont work but when i drive down the road if i hit a bump it turns on and i hit another bump it turns off. How do i fix this or go about finding the blower motor I had the same problem with the fan for heat only when I hit a good puddel of water the fan dies down and then gives out. I replaced the Resistor /Resistance in Nov. 2007 it worked fine. The same thing happend again in Nov. 2008 and after one slushy puddel the fan is out again. Do I have Hol


I had the same problem and replaced the blower motor . it is located up under the glove box . and I test the old one and it would run fast if i shook it .the bearing or something wears out in them . I got one from a wrecked car for 20 verses 78 new ... 2002 Pontiac Grand Prix

The Kia dealership said one of my motor mounts was loose--I got a seconf opinion and they said there were 2 motormounts and one other (transmission) maybe but they were all solid. My question is how many motor mounts are there? It is a 4 cylinder


Probably 4, one in front and back mid engine and one on front of engine next to fender and one on end of transmission. Loose may mean not physically mounted but rather rubber separation inside the mount where attaching bolt is anchored. Just put fron ... 2005 Kia Optima

I have a 2000 Saturn LW2 V6 3.0. My heater quit working 2 years ago so I did my hw and found it to be the blower motor resistor. Well, the heater quit again with the same symptoms as before...intermittance...sometimes it would work on all settings, sometimes not at all and would come on or tirn off as I was driving down the road. I replaces the resistor yesturday...today..NO HEAT! Could someone please give me a clue as to what could be causing this to happen? I say a short or the blower motor is


With the vehicle running and the blower switch set to high and the blower motor not working tap the bottom of the blower motor with the handle end of a screwdriver. If the blower starts to work it is bad. Usually the brushes are worn out and tapping ... 2000 Saturn L-Series

My ford explorer 1997 V6 4.0L my truck start but unless i press the gas but as soon as i stop giving gas the truck stop i got told i need to change my alternator because i just changed the blower motor and its havent start since i changed the blower motor so please help me guys


Doesnt make sense, you went from giving gas to keep running ,to switching blower motor,Heater blower motor i assume? to replace alternatoer? i'm lost, blower motor has nothing to do with the motor running or not. the alternator charges the battery in ... 1998 Ford Explorer

Hey out there...I have replaced the resistor blower motor module, the upper and lower gaskets for the intake manifold?, the ignition switch, the ignition cylinder,had the a/c line cleaned out, and a new battery put in. My '03 grand prix gt is still having issues. Starts some days, and then won't start. It sounds like a machine gun when it won't start. I have ordered the $4.00 recall replacement part that goes over the blower motor. I am just so glad I purchased this car four months ago for my 17


When it wont start is it a clicking noise starter could be going bad, or cranking over and making this noise,some cars you get it just keeps going depends on if the previuos owner didnt do anything to it or not, then you end up rebuilding the whole c ... 2003 Pontiac Grand Prix

My 2000 mustang v6 3.8 l started shaking out of no where from startup to every speed its only not to bad when coasting ive changed harmonic balancer motor mounts spark plugs ive brought it to 2 mecaniques that just cant figure it out im gonna change the trans mount this week but do you know what else it could be


Change the driveshaft yoke ... 2000 Ford Mustang

Motor mount i think my rear motor mount might be broken and ive looked everywhere online and cant find a diagram. i have a picture of it but thats not helping me either. if you could put me in the vecintity of where its located that would be great.


The front mounts support the engine at each side (passenger and driver side of the engine block. These supports are made of resilient rubber.REMOVAL(1) Disconnect negative cable from battery.(2) Raise the vehicle ... 1998 Jeep Wrangler

How do I change the rear blower motor on a 1999 Plymouth Grand Voyager SE? is making squealing noise. Front motor only works if I give motor a light tap after turning on. could that be resistor or motor?


... 1999 Plymouth Grand Voyager

I have a 95 probe SE witha 2.0 liter 4 cylinder and i want a motor with more performance like a 2.5 v6 or evena 2.2 turbo since i heard that was possible problem is i dont know what i need to make this happen people say if i go v6 ill need a new tranny, motor, motor mounts computer etc. but others say if i go to a 2.2 turbo it be an easier process so my ? is whats easy or the better choice to go with that'll save me time and money


HI less headache less frustration, better more reliable motor 2.2 turbo great motors and you dont need to change transmission , get you turbo motor, find it at www.car-parts.com ... 1995 Ford Probe

Where is the heater.a/c blower motor resistor located on the firewall mounted system?


... 1996 Lincoln Town Car

Front motor mount on 1993 camry 4 cylinder


The mount is probably bad anyhow. so get it out however you need to, you can always cut the nut or bolt off and the new mount will have a new stud. so you will only need a nut. ... 1992 Toyota Camry V6

I have an 02 crown vic and now the blower motor just quit working i put a new motor on it and checked the fuse but it still dont work ive been reading up and there seems to be alot of peolpe saying the resistor but its 100 dollars what do you think


On my 2004 Ford Crown Vic One day it just stoped blowing no A/C or heat i checked all the fuses and relays and they are fine so i guess its the blower motor and i want to know the location and if is easy to chang \\??? Or if might be somthing else c ... 2004 Ford Crown Victoria

1994 Silverado heater blower does not start when switched on. Give it a whack and it works at all speeds. Blower motor or relay?


Disconnect the wire leads from the blower motor and check for 12 volts. If there is 12 volts, then the blower motor electric brushes are worn and the unit will need to be replace. If there is no Voltage, then your have a switch or relay issue that ne ... 1994 Chevrolet Silverado 2500

Blower motor i just bought a 1997 ford escort and the heat isnt working. the heat comes out but the blower isnt working. ive searched for a fuse. but cant seem to find one at all.


Actually there is a circuit breaker just above and to the left of the fuse panel under the dash. If it has tripped there is a little button in the middle to depress to reset. ... 1997 Ford Escort

99 Kia Sportage, 2wd, automatic, 4 cylinder. The a/c will not work with the a/c switch in, blower on any setting (blower motor is fine at all speeds) temp control on coldest blue area. Have checked all fuses - every fuse is good. If I jump the compressor with 12 volts, the a/c pump will come on, will get very cold air inside, low pressure side lines will get cold sweats.... so everything in the a/c system is working fine cold air wise......it just won't come on (operate) when you push the button


A/c control unit/module seems to be defective!!!!! because its the one that switches on the compressor! ... 1999 Kia Sportage

I have a 99 intrepid, the blower motor works when it wants to. when working works great, ive pulled the motor out and hooked to power, works great. could it be one of the switches?


Replace the fan resistor under the dash most likely in the area of the glove box underneath, it is screwed into the side of the heater box ... 1999 Dodge Intrepid
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.7967 seconds