Having problems with your 2004 Chevrolet Impala ?

Looking for head bolt troque spec for 3.4l impala sfi04

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Please don't forget to rate. Thank you:
\012
\012Left side front cylinder head
\012
\012
\01298e175a.gif\012
\012Cylinder head bolt torque sequence-3.4L engine
\012
\012\012
  • \012Cylinder head by aligning it with the dowel pins
  • \012
  • \012New cylinder head bolts coated with a sealant (such as GM 1052080). \012Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). \012Using a torque angle meter turn the bolts 90 degrees in the proper \012sequence.
  • \012
  • \012Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • \012
  • \012Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • \012
    \012
    \012Right side rear cylinder head:
    \012
    \012
    \01271cd5b7.gif\012
    \012Cylinder head bolt torque sequence-3.4L engine
    \012
    \012
    \012
  • \012New cylinder head gasket
  • \012
  • \012Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • \012
  • \012New cylinder head bolts coated with a sealant (such as GM 1052080). \012Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). \012Using a torque angle meter turn the bolts 90 degrees in the proper \012sequence.
  • \012
  • \012Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • \012
  • \012Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • \012
  • \012Spark plug wires
  • \012
  • \012Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • \012
  • \012Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 \012Nm). Using a torque angle meter torque the fastener an additional 30 \012degrees.
  • \012
  • \012Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • \012
  • \012Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Repair Help & Product Troubleshooting for 2004 Chevrolet Impala

    Tips for a great answer:

    - Provide details, support with references or personal experience .
    - If you need clarification, ask it in the comment box .
    - It's 100% free, no registration required.

    Suggested Questions/Answers :

    Looking for head bolt troque spec for 3.4l impala sfi04


    Please don't forget to rate. Thank you:\012\012Left side front cylinder head\012\012\012\012\012Cylinder head bolt torque se ... 2004 Chevrolet Impala

    I have looked on alldatapro and indentifix and still can not find the torque specs for the lost motion assembly holder and rocker arm assembly that bolt to the head. it is for a 1997 Honda Civic EX 1.6L with vtec head. i think the rocker arm assembly might have some warpage due to the previous torque specs i was given. having a hard time telling. ne help pls?


    ... 1997 Honda Civic

    Looking for rod and 11mm head bolt torque specs for an XN1 Peugeot engine.Also looking for valve settings and info on how to choose the correct thickness bottom cylinder seal?


    ... 1989 Peugeot 405

    Head bolts torque specs for a 2002 impala - 2002 Chevrolet Impala


    ... 2002 Chevrolet Impala

    I ned head bolt troque spec for kia rio 1.5 a5d eng


    ... 2004 Kia Rio

    Looking for the torque specs for the head bolts for a 4.7L land rover discovery


    Not sure if you know this but you can go to \015\012\015\012mitchell1diy and for ten bucks you can get everything about your car. ... 1997 Land Rover Discovery

    I have 1999 V70, I am looking for torque specs for head bolts. Thanks.


    ... 1999 Volvo V70

    Looking for torque spec. for head bolts on a 1980 Toyota Cressida 2.6L 4M-E engine? Can you help?!


    ... Toyota Cressida

    Head bolt troque spec for 1.5L toyota 2001 Echo


    ... 2001 Toyota Echo

    Head bolt troque spec for 1.5L toyota 2001 Echo


    ... 2001 Toyota Echo

    Looking for head bolt torque specs on a 1974 ford f150 with a 302


    ... 1981 Ford Bronco

    Torch specs on cylinder head bolts - 2003 Chevrolet Impala


    You didnt mention which engine you have.\0123.4l = 44 ft/lbs plus 95 degrees.\0123.8 = 37 ft/lbs plus 120 degrees.\012Good luck ... 2003 Chevrolet Impala

    Looking for head bolt torque specs on 2.2 ltr olds alero 2003 year


    Chilton and haynes have a great bible for your car \015\012chapters indago sell em cheep ... 2003 Oldsmobile Alero

    Looking for head bolts torque specs for 2006 chevrolet malibu


    WHATS YOUR ENGINE SIZE. 2.2L 3.5L OR 3.9L HAD 3 DIFFERENT SIZE ENGINE THAT YEAR. ... Chevrolet Malibu

    Took my 1997 ford taurus with 3.0L to a shop did a compression check on the back cylinders (1,2,3) 1&2 were at 50 psi. They said more then likely it was the botom end of motor which has the problem. Now wouldnt it blow smoke an burn oil if the piston rings were bad? The head looked fine the block as well, New gasket an bolts were installed tightened to specs. This car runs almost perfect except when u put it in gear it stumbles like it out of timing. Where should i go from here?


    Have the shop do a leakdown test and verify the problem, it could be a bad head gasket or a burnt or stuck valve. ... 1997 Ford Taurus

    2003 chevy impala torque specs for head bolts


    ... 2001 Chevrolet Monte Carlo

    I am looking for torque specs for a 2.2litre chev head bolts


    ... Chevrolet Beretta

    Intake bolt torque specs for 3.4l impala sfi04


    ... 2004 Chevrolet Impala

    Im looking for head bolt and rocker arm torque specs for a 1995 chevy G20 van with the 5.7 liter engine


    The way to get these specs it to spend the 14 bucks on a chiltons book for your model truck.hate to say that. i have about 20 chiltons books they are worth it trust me on this.they will give you specs diagrams and how too's of your truck.you can get ... 1995 Chevrolet G20

    Looking for torque specs on a hyundai accent gl for the head bolts


    \015\012\015\012 \015\012\015\012For 3.0L engines, tighten head bolts in sequence to 76-83 ft. lbs. (105-115 Nm).\015\012 \015\012\015\012For 2.5L engines, tigh ... 2000 Hyundai Accent

    I'm looking for the head bolt torque spec and timming mark setings


    ... 2000 Volvo V70

    I need torque specs for a 08 3.5 v6 head bolts rocker bolts and intake bolts i replaced head gasget and need torque specs so i can put it back togeather


    ... Chevrolet Monte Carlo

    1992 Mitsubishi Mighty Max 2.4 head bolt torque sequence and specs


    ... 1989 Mitsubishi Mighty Max

    I don't have the head bolt torque specs for a 1956 willys jeep


    ... Toyota Celica

    Hyundai accent xs 1300 1998. Need the torque specs on head bolts, fly wheel, main bearing and big end bearing. Also need to know if the head bolts is strech bolts and do I need to put in new bolts


    ... Hyundai Accent
    • Start your question with What, Why, How, When, etc. and end with a "?"
    • Be clear and specific
    • Use proper spelling and grammar
    all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
    Load time: 1.5390 seconds