Having problems with your 2003 Nissan Maxima ?

2003 nissan maxima at/cvt code

\015 In a Nissan maxima 2003 have active code at /cvt\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2003 Nissan Maxima

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1996 nissan maxima jolts and loss of power Car turns on fine at first, I drive for a while and then the car starts to jolt like gas is trying to get to the carborator but can. It then starts jolting alot, then the horsepower goes to 0 and the car shuts off, showing the battery and oil light. It takes me a few times to get the car running again, will do that jolting thing for a while then it goes back to driving normal. I took it to a mechanic and he stated that when he read the codes it came up


Dear friend-what i can gather from you explenationis that the feul pump is on it"s way out.have that tested and come back with the fault codes if that is not the problem. ... 1996 Nissan Maxima

Can anyone tell me what these engine fault codes refer to on a 1998 mercedes c180 auto,1.8 petrol. I suspect it may be releated to tempeture sensor. Total of 6 codes 065 (2,2,0,41) resistance too high 104 (2,2,0,68) resistance too low 122 (2,2,0,7a) resistance too low 126 (2,2,0,7e) resistance too low 129 (2,2,0,81) resistance too low thanks jim 161 (2,2,0,a1) resistance too high


Most common is o2 sensor ... 2002 Mercedes-Benz C-Class

Nissan x-trail fault codes that came up at service, the Nissan Dealer could not tell me what the fault codes meant, can any one help with the following codes? P0725, P1726, P0826, U1000


P0725=engine speed input circuit.p0826=up and down switch input circuit.ime not sure what the other 2 codes are sorry. ... Nissan Xterra

I have a nissan largo that cuts out when i put it in gear done a fault code reading comes up with code 1-5 =lean mixture 1 8= ant got a clue code 2 1= IAC valve or its cicuit fault no ignition signal from ECM does it want a ECU or may be a fuel injector pump. thanks marg12 forgot to add it a 96 nissan largo 2lt diesel.


... 1986 Nissan 200SX

Why does the speedometer on my nissan altima 2002 goes up and down then the car shuts off, unable to restart trouble code 1540


... 2002 Nissan Altima

Engine codes Does anyone know the what the codes u1000 and u1001 for a 2002 nissan altima are? I've been everywhere can't find anyone that knows. Where can I get a manual for a 2002 nissan altima?


Sometimes coming data,but the every error comunication,for the scannner rpm up and down same the lightgauge,low high,codes u 1001 1000 ... 2002 Nissan Altima

I have a 1997 nissan sentra that wi have a 1997 nissan sentra that wont pass emisions fuil system lean bank1 p0171 code so i changed the maf sensior,fuil pressure reg, pcv valve, and all four fuil injectors, now the car has no power at all it hardly move now with pedle to the floor it wont go can any body help me please. ont pass emisions fuil system lean bank1 p0171 code so i changed the maf sensior,fuil pressure reg, pcv valve, and all four fuil injectors, now the car has no power at all it


Have you checked your fuel pressure at the fuel rail? The problem could be a clogged fuel filter, pinched fuel line, or under-performing fuel pump (either faulty part, or not receiving enough voltage).The only other thing I can think of t ... 1997 Nissan Sentra

I have a 2000 Pontiac Bonneville 3.8 non supercharged. It is throwing the codes P0446, P0452, P0453. Yes it is throwing all of them and that is what is confusing me. Just reset the codes, did a start-stop-start-stop and got the 53 twice. Also, the fuel pressure isn't good, you hook up the gauge you get 0, when you turn the key on it jumps to 50 and as soon as the pump shuts off it goes back to 0, and when running it stays at about 47. I would greatly appreciate any help. and no my craftsman


... 2000 Pontiac Bonneville

Engine repair code P0325 on a Nissan frontier v6 3.3 engine repair code P0440 on a Nissan frontier v63.3


Po325--ignition system or missfire. ... 2000 Nissan Frontier

Nissan I have a nissan pathfinder 2000 with a 3.3l I have code p0325 I change the knock sensor code and p0325 is always present


OK the sensor may not be bad, you might have a broken wire to the sensor. Or a bad plug, I would by pass the sensor plug - cut it out. Cut one wire at the time and reconect using a crimp on union (bu**) conector. You may also have a timing issue, tha ... 2002 Nissan Pathfinder

P1168 code andp1051 code 2004 nissan maxima - 2004 Nissan Maxima


... 2004 Nissan Maxima

1995 nissan pathfinder 4DR key broke off in door cylinder passenger side front. I dont have another key and its to old to get a key code from Nissan. The dealer said there possibly is a key code on the cylinder. I need a schematic of the door panal and the cylinder that shows me how to remove the door panel and how to remove door cylinder. [email protected]


... 1995 Nissan Pathfinder

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

I recently replaced the passenger side head gasket on my 3.3L 2000 Nissan Frontier. The Check Engine light was on so we scanned it, and it was throwing 3 codes, the first one was a Code 34, the knock sensor code and the other was a Code 71. The code reader didn't have a definition for these codes. Any clue to what they are?


In your air box you will see a wire with a sensor on top,,replace this sensor and engine check light will be gone the next time you start the jeep ,job done ... 2000 Nissan Frontier

I have a 1998 Nissan Maxima GLE, I Failed the Emission Inspection (DTC) Diagnostic Trouble Codes of "P1492","P1105" What these Codes exactly? mean


A code P0300 may mean that one or more of the following has happened:\012Faulty spark plugs or wiresFaulty coil (pack)Faulty oxygen sensor(s)Fault ... 1998 Nissan Maxima

I have a 2001 nissan pathfinder got 3 codes code P0300 random missfire replaced 3 coils &all plugs now runs on all 6 but either 1 side or the other leans out loses power and the code comes back the other code s are P1320 no primary signal & the othercode is low activity from bank1&202sensors


The crank angle sensor should be replaced and that would correct the P0300. I would also replace the plugs and coils and that should take care of the random multiple misfires. The timing control position sensor on the right bank and possibly the va ... Nissan Pathfinder

Transmission I have a CVT control system code of P1700 and Control Area Network (CAN) communication line code U1001. My research has resulted in only the Nissan dealer having a scan tool to get into the transmission to check for transmission codes. There is a TSB (NTB06-009A) for CAN communication codes U1000 and/or U1010 for ground issues.


... 2003 Nissan Murano

2002 nissan sentra 1.8l had a po011 code, took a compression check 150lbs in 1 and 4 cylinder and 90 in 2 and 3 cylinder, replaced camshaft and crankshaft sensors. Po001 code did not come back, but po507 came up, checked for vacum leaks(none), cleaned throttle body, checked all connectors(ok), cleared code,code came back, my question is, is this a blown head gasket between 2&3, a bad air volume actuator, a bad intake or? And what procedure(s) should i preform next and how? (I try the idle relear


... Cars & Trucks

My 2004 Nissan Xterra was running well w knock sensor code. Had it replaced and now in the morning it starts and sometimes stalls. Comes up w the code for the IAC. Tried to reset code and doesn't go away at all like the other code did. Trying to locate the IAC w no luck. Is there a picture of one in the engine I could look at?


... 2004 Nissan XTerra

1988 honda civic stalled,code 16,replaced main relay,code now reads 0,car still dont start


... 1988 Honda Civic 2 Door

I have a 2004 nissan Titan with codes 1148, 1168, 1031, and 1051 active. I recently replaced all 4 O2 sensors. I still have these codes. I have reset the codes using the hand held diagnostic tool and


... 2004 Nissan Titan

2002 nissan maxama 3.5 motor code is high voltage 02 sensor bank 1 sensor 2 replaced new sensor drove 15 mi. code and light come back on.any help , please


... Cars & Trucks

2002 nissan maxama 3.5 motor code is high voltage 02 sensor bank 1 sensor 2 replaced new sensor drove 15 mi. code and light come back on.any help , please


... Cars & Trucks

OBD Test diagnostic trouble codes for 1998 Nissan Maxima GLE Code p1492


... Nissan Cars & Trucks

ABS lights and slip light stays on my nissan titan 2007.I have a code that comes up p1668 is that the code for the sensor


... 2007 Nissan Titan LE
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6052 seconds