Having problems with your 2003 Kia Sedona ?

2003 kia sedona. what size is the nut on the front wheel bearing and is there just one bearing on each side or 2? Do I need a special socket to remove the nut?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

The size of socket ur looking for is 32mm & as for bearing i'm sure that its a complete bearing.
Repair Help & Product Troubleshooting for 2003 Kia Sedona

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2003 kia sedona. what size is the nut on the front wheel bearing and is there just one bearing on each side or 2? Do I need a special socket to remove the nut?


The size of socket ur looking for is 32mm & as for bearing i'm sure that its a complete bearing. ... 2003 Kia Sedona

Need to replace broken front driver side wheel stud on 04 impala - seems like i have to remove hub to make room to push stud through? can someone confirm? if so, how do i get hub off - is it just a matter of removing the axle nut? I don't have a socket big enough to do that, so don't want to buy one unless i have to :). Also, sure would be nice to find an exploded view digram somwhere which names the various parts! thanks!


In the perfect world you are to remove the hub and bearing assembly and yes you would take the axle nut off,but when you are paid flat rate as a mechanic you must beat factory quoted time to make money,so with that said,remove the wheel after c ... 2004 Chevrolet Impala

1999 Chevrolet Blazer driverside wheel bearing locking nut on the cv joint won't loosen can't remove bearing until i remove the nut i tryed 36mm socket with impact gun still nut will not loosen need answer ty


This will require a "breaker" bar. I would use a good quality 1/2 inch socket set with a fixed wrench handle. To extend your power, I would put a pipe extension onto the wrench and turn until the bolt "breaks" free. NOTE: make sure you are removi ... 1999 Chevrolet Blazer

I think I need to replace the drivers side wheel bearing on my 1999 gmc 4x4 6cyl 5speed , I have the brake calipers off . It looks like I need a 1 3/8 socket to remove the rotor , my question is does the bearing go directly behind the rotor or will I need to remove more of the axle ? And what will the cost of the parts be to do the job , thanks. Paul .


The bearing should be behind the rotor give these websites a try www.alldatadiy.com or www.autozone.com if a ... GMC Sierra 1500

Hi, i need too replace my rod bearrings in my 2001 f150 ford pick. it is a triton. with a 5.4 engine .my question is ,is there any special torque requirement, or can i simply remove my old ones and replace them with the new ones, do i need any specials tools. thank for your time


... 2001 Ford F150 Styleside SuperCrew

Need to know how to remove the bearings on the front spindles on a 4 WD 1985 dodge truck 250 3500lb front axles. they look like they should just slide out since i removed the gasket but they do not. I replaced the U joints and thought I should go ahead and replace bearings and oil seals(done with oil seals). I have tried prying them out but they are in there pretty good, didnt know if someone had a trick i could use or is there a special tool one needs. Thanks Billy


... 1985 Dodge Pickup 4WD

Engine mount I am working on a 2003 dodge neon. I am try to replace the timing belt. I cannot remove the right side center engine mount. The one that comes through the right side wheel well. I need to remove it, I believe because the bracket that the power steering pump attaches to has a bolt that I cannot access without removeing the mount. Unless there is a special tool required there isn't enough room.


Raise engine up as high as it will go. ... 2003 Dodge Neon

Help please, I need to remove the inner wheel on the rear of my toyota dyna tipper truck...sounds easy, but the outer wheel nuts only hol;d the outside wheel, its pasenger side so the nuts are left hand thread..no problem there, but the inner wheel is held in by the stud itself, not the wheel nuts, the end is a square about half inch, ans an ordinary socket does not go on, its square like a square nut, I can not tell if its left hand thread or not, i can get an adjustable spanner on just about,


... Cars & Trucks

I have 2001 Chev Tracker, Oil started to run out of the Right side break drum. Removed Drum and foud oil all over the breaks. Tried to remove the Axel by removing the four nuts off of the backing plate, Axel wount come out. I think the bearing and seal are bad. I need a picture of the breaks also, not real sure of were all the springs and other parts go. How is the axel removed?


The axle requires a slide-hammer to remove. And usually the axle bearing is destroyed in the process. A new axle bearing needs to be pressed on by a machine shop, and then the reinstall of the axle requires the correct application of concussive for ... 2001 Chevrolet Tracker

Can't get the nut on the l bracket off to remove starter.is it sae or metric?theres a heat shield on one side of starter that appears to become a l shaped bracket on end of starter with a bolt coming from the starter,and a nut holding it. i am unable to see any other restraints on the starter. i need to replace the starter,so how do i get the nut off,what size is it- sae or metric?


Almost all vehicles from 1980 on are 90% Metric\015\012\015\012You need a lot of tools to work on todays vehicles ... 1983 Oldsmobile Delta 88

Rear end accident.Left rear side caved in just past rear door.Large piece which connects brake assembly (drum),shock, 2 arms to chassis and one arm with ball joint to cross member. The large piece broke where the ball joint connects to it. In order to remove the large piece it was neccessary to grind off the nut on the ball joint. Now I need to replace the arm to the crossmember but I cannot remove the bolt through the crossmember. Is it pressed in? How can I remove it? Any help would be greatly


... 2001 Mitsubishi Galant

1992 Subaru Legacy, 2.2. Replacing the water pump and timing belt. I have removed the radiator and side belt covers but can't get the center cover off. The cam pulley turns when I try to remove the nut. Do I need a special tool?


... 1992 Subaru Legacy

How do I change the Sparkplugs on a 2005 kia sedona van? Theres a plastic cover (No Problem). Remove wires (No Problem) Except the top of the plug looks different than most & recessed very far into engine. Do I need a specialized socket & tool (Can I purchase at automotive shop Checker, Autozone etc.. Or is it a special order item?), especially in the back 3 plugs, on the firewall side. Thanks for your Tips.


It sounds like you removed the intake manifold if not you need to remove it. Use a 5/8 spark plug socket 2 extensions and ratchet I hope this helps you ... 2005 Kia Sedona

Need to know the size of the nut on the hub that must be removed in order to replace the front wheel bearing on a 2006 Toyota Matrix. A full set of instructions would be great, but knowing the size of the nut will determine which socket I have to buy. Thanks


... Toyota Matrix

How to remove upper transmission line clip from radiator on a 1996 ford taurus? I have undone the retaining clip. Now I'm looking at a plastic plug that's secures the hard line to a large hex nut that's screwed into the radiator. Do I pry the plastic plug out, does it screw out or pull out, do I need a special tool to remove it. Do I take a needlenose pliers and pinch the sides in the pull back the line from the radiator. Thanks Leo


... 1998 Ford Taurus

My driver side brake lights are not working on my 2001 Toyota Highlander but the parking lights do...connection is only good on one out of 3 on both lights...changed bulbs and switched sockets so I know thats not the problem. Was told by another expert to remove and replace lamps due to connectors not connecting. Does this sound correct? I will need to do the repairs myself so how do I remove the lamps?


Have you probed the wiring to the bulbs to see if there is 12 volts makeing it out? Go from the switch out and check until you locate whwere the circuit is lost. ... 2001 Toyota Highlander

I have what sounds like a front wheel bearing noise on my 2007 Lexus RX 350. 1. How do I identify if it is coming from the right or left wheel (the noise increases when I put steering wheel pressure to the right and almost completely disappears when I move the wheel to the left? 2. What size socket is needed to remove the axel lock nut?


Jack up one side at a time and get a big bar or a strong 2x4, lift the wheel, have somebody lift while you peek at the inside and see if you can see something loose, grab the wheel and shake it left and right, It should tell you something, If, not, t ... 2007 Lexus RX 350 FWD

What size socket do i need to remove the nut on the front wheel bearing on a 2005 gmc sierra 1500?


... 2004 GMC Sierra 1500 Crew Cab

When I was changing the spark plugs I removed an electrical part from the rear passenger side of the manifold (1/2" of threads, large nut, electrical wiring). The threads sheered off upon replacing this part. Need to know what it is called so I can get a new one????


It sounds like a pressure or temp sending unit was there any fluids on it or was it caked with a black film,also was it brass or aluminum.The best way to find out what it is is to disconnect the wiring and just take the part into your local parts sto ... 2003 Kia Optima

Needed to replace both CV joints on a 95 Camry. Passenger side would not come loose. The CV joint comes all in one piece, although my step Dad seemed to think that it could have been pressed into the engine mount brace that the bearing and race are set in. I removed the snap ring and also the bolt that is supposed to release the whole shaft and it wouldn't budge. Is there an easy fix and answer to this problem?


Circlip in back of cv on the end of the shaft ,cut boot away and look inside on end of shaft their should be a cut away on cv and that is the access to get the circlip loose whilst you wack the cv with a mallet ... 1995 Toyota Camry

1990 acura legend auto. trans. need to remove pass. side hub nut', i am using a 36mm impact socket to loosen it ,but no luck!


You will need to use a really long manual breaker bar to crack that nut. They bind on really tight, going from hot to cold over years of driving. Soak it with some liquid wrench. It takes substantial leverage to crack the nut, but it will come loose ... 1990 Acura Legend

Replacing front wheel hub. drivers side. what size is the socket needed for hub nut? also, How to remove abs electrical wiring that goes through the wheel well?


... 2002 Jeep Liberty

Size socket needed remove wheel bearing nut - 2008 Dodge Caliber 2.0


... 2008 Dodge Caliber 2.0

I have a 1998 Eclipse RS Non-turbo 2.0L, I am trying to remove the transmission and to do so i need to remove the half-shafts. The problem is that the nuts that hold the half-shaft to the rotor are rusted on and they are impossible to remove, Even with a braker bar. There are no Cotter pins in the nuts, because i looked to see if it was preventing the nut from being removed. Is there a special way to remove these nuts and i am just not doing it right or is there a way to remove the half-shafts f


Because there are no cotter pins, they were most probab;y fitted and fixed with Loctite or similar.\015\012\015\012Try applying a bit of heat to the nutwhile you have pressure on the nutm with your spanner.\\\015\012\015\012An ... 1998 Mitsubishi Eclipse

How do I remove a 2002 Jetta driver side seat? Non-power.Trying to replace a Airbag connector. Aware of airbag issues. Just need to remove seat. Can only see two small nuts in front floor area with seat pulled back all the way. is that all? no rails? They two nuts look to be square. I can't see much else. Do i need to remove carpet?


... 2002 Volkswagen Passat
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.4222 seconds