Having problems with your 2003 Hyundai Tiburon ?

Cam gears keep moving when trying to replace timing belt on 2003 hyundai tiburon V6

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2003 Hyundai Tiburon

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cam gears keep moving when trying to replace timing belt on 2003 hyundai tiburon V6

... 2003 Hyundai Tiburon

I have replaced the timing belt but it keeps slipping. I have all new pulleys and a new tensioner. The belt tends to drift to the inside toward the engine while its running. It runs fine until I start to accellerate like from a stop sign trying to get into traffic. The belt keeps slipping or jumping a tooth or four only on the cam gear near the firewall. Its done it three times with three new belts. I put the old tensionr pulley back on but with the same results. Cam gears are not bent. I am run

It's not the tensioner pulley. It's the tensioner itself. The spring on the inside has become weak allowing the belt tension to move it just off of "square" to the engine do it's acting like a cone. Smaller on one end than the other. The belt wan ... Mazda Millenia

Brother replaced water pump and took timing belt off and accidentaly moved gears...now water pump and timing belt is all back together and car wont start because timing gears are off....What are the gears suppose to be on for a 2000 kia Sephia?...a diagram showed up e and i...and we tried it and did not work...What to do now?

Call a professional mechanic as you will bend all the valves and possibly make a hole in a piston ,IF YOU HAVENT DONE SO ALREADY ... Kia Sephia

My timing belt keeps coming off, I have replaced the tentioner two time's and bought a new belt, after i get the belt on and start the car, the belt kicks off again. I tried bypassing the air conditioner with a smaller belt, Which was advised for me to do from a garage, but the tentioner just kicked it off. I can't get it to a garage because it won't stay running, and it cost's like 300.00 to have a tow truck move it for me! Do you have any idea why this might be happening? I need my car back A.

Idler pulley gone ? Make sure your alternator and every thing else lines up ...good luck ... 1998 Ford Contour

2004 Hyundai sante fe 2.4litre was driving on expressway when check engine light came on then truck died out wouldn't restart had it towed replaced timing belts also replaced cylinder head and gasket lined up timing marks for crank and cam started and ran for 5 min then died out won't restart think timing belt jumped out of time? before replacing head just installed timing belts and lined up marks but would not run at all none of the other pulleys are froze up and are moving freely did replace

Its possible that you have any problem with the cranks position sensor... scanned the PCM to know exactly what fault code is soterd there and tell us news. ... 2004 Hyundai Santa Fe

Timing belt was very loose so i changed the timing belt tensioner pulley.I tried to make sure and not move the timing belts position on the cam and crank but now im not sure if it may have moved.I located the crank tdc mark but i don't know if the cam tdc mark faces up or down.And once i get these marks lined up how do i get the belt back on without moving the gears. The engine is shutting down almost immediately after start so I want to make sure timings not the problem.

Sorry for the severe delay. I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.\015\012 \015\012Click ... 2001 Volkswagen Jetta TDI

Timing belt i replaced the timing belt got the car to start..first problem...it started but the drive belt tensioner wont stop moving now and it is making a knocking noise everytime it bangs ...second..the car wont turn off when i turn it off it will run for like another minute or two...third i have a broken throttle position sensor..will replacing the throttle position sensor and the drive belt tensioner fix my problems...or did i not time the engine right when i changed the belt..keep in mind

You obviously need to replace your TPS, and you may need a new belt tensioner as well. On these cars the timing belt setup is not about no 1 cylinder being top dead center. Here are the proper steps to do a timing belt on this vehicle:\015\012 ... 1996 Ford Escort 4 Door

I have a Hyundai Tiburon GT V6 and I had to swap the motor out because my timing belt broke on the old one and it locked up. Now my car keeps stalling after prolonged use and high revs and I have to wait about 20 minutes before I can try to start it up again. Is it the crank sensor or does the ECM need to be reprogrammed for the new motor?

... Cars & Trucks

1998 DODGE STRATUS ES V6 2.5L - Replaced water pump, made sure nothing moved, crank shaft and cams. put everything back on and engine would not turn over. pulled all the belts off even timing belt and try to turn to crank shaft. the crank shaft would only turn haft way and sound like it hit something. I line all the marks on the cams and crank shaft and put the timing belt back on, then try to start it. the engine turn over two times and lock up. there is nothing in the cyclinders, all the valve

... Dodge Cars & Trucks

The car is a 2000 eclipse gt 3 liter the only mod in this engine compartment is a cold air intake. 129,xxx miles Let me start from the beginning. My harmonic balancer shattered into pieces. During the replacement the gear driving the timing belt came out. Since the timing belt has not been replaced since ownership I decided to replace it along with the water pump. After setting all the timing marks, everything was reassembled. The engine started on the first try, the fallowing day, car was taken

First of all you never spray a electrical component with water. Now there is no way to know what sensor shorted or whether or not it shorted out the computer also. What you need now is a data scanner in order to see if any codes were set and to ... 1995 Mitsubishi Eclipse

Intake and exhaust cam pullyes moved when timing belt was taken off, was trying to replace timing belt and I did mark pulleys myself before taking belt off. Now the pulleys will not move, theres compression behind them. Is there a way to get them back to my marks, and if I have to reset timming how do I do that. It's on a 2002 Daewoo Leganza, Thank You

It is not compression causing the resistance while trying to turn your cams. It is the valve spring pressure so taking out your plugs would be useless. In order to rotate the cams freely you have to remove the valve covers and loosen all the Valve ad ... Daewoo Leganza

Valve timing off no compression.. timming belt has slipped I am trying to replace the belt but i want to make sure that the valves are in the right order since the belt was missing numerous teeth... the books all show how to keep it it time when changing the belt but not how to re time it

There is a timing kit for timing the focus one locks up the crankshaft and the other fits into the slots on the rear of the camshafts all the pulleys cam and crank dont have keyways they are freefloating when loose and if it jumped more than one too ... 2001 Ford Focus

2000 hyundai accent with 107,000 mi. Went around a corner and it died. Would try to restart but wouldn't. Someone said it was the timing belt and that the engine would have to be replaced. Timing belt is still on and doesn't seem to have any wear. We have replaced spark plugs and plugs. What else could it be?

Check the crack positioning sensor. It's located (on the 1.6l) on the front of the engine, right-side, toward the front top. ... 2008 Hyundai Accent

Trying to find out to replace a timing belt on a 1994 Maza B2300 need to know how the gears are position back do you have any images I can see how to replace my timing belt back?


I have a 1998 dodge stratus es v6 2.5L water pump started leaking I took off the belts and covers and timing belt replace water pump put belts back on engin will not turn over. took off timing belt try to turn crank shaft it would not move. it's like it is hung up on something.

... Dodge Stratus

I broke my timing belt on my 2000 hyundai accent i took off the timing belt cover and the belt was mangled and the line up marks were off i then took the plugs out and found out that my forth plug was damaged a little bit internaly so i then took off the valve cover to see if i could see any valve damage i dont see any so i try rotating the crankshaft and i can only move it about a quarter and it stops what kinda damage am i looking at and how much to fix

Hard to say. Depends on how fast the engine was running when it broke. Sounds like pretty fast from the belt getting mangled, right? You can put a new belt on and see if the engine will turn. If not, you know you've at least got some bent valves ... 2000 Hyundai Accent

Hi, i have a 2001 model and am trying to decide if my car is worth the price of repair. while driving the car just stopped, i was told it sounds like the timing belt. it has been started several times but not moved. the question is i was also told that when the timing belt goes on this type of car the valves usually need to be replaced also. is this correct? thanks

You said that it has been started several times,do you mean the engine fires and runs........? ... 2001 Daewoo Lanos

Have a 2005 Hyundai Sonata and for the last year it has a high pitch squeak almost always when the engine is running. I had it into the shop three or four times and they tried to get the squeak to stop. The accesory belt idler pulley was replaced and also the tensioner pulley bearing has been replaced. A new pull was put on and we were also told to use a wire brush on the belt when the squeaking starts again. This above repairs usually only worked and kept the squeak quiet a week or two. Even wh

Occasionally this will happen. Here are a few tricks to hush the noisy belt. Try using another belt from another manufacturer. Its true you do get what you pay for. A better belt may be the ticket. Another trick is to lightl ... 2007 Hyundai Sonata Limited Sedan

When I removed the timing belt to replace the water pump I did not mark the belt and gears like I know that I should. Now have a problem with starting, it won't. The cam gears did not move more than a tooth or two. Dan

Simply buy a new belt from Nissan. Line up the marks on the belt with the marks on the cam gears and crank gear and it will start. ... 1997 Nissan Pathfinder

I have replaced the engine top of my toyota hilux KZTE 2003 model, due to cracks in the engine top. I did not align all the timing marks on the engine before removing the timing belt. I did not adjust or remove any part of the timing gear on the engine block. I tried to set the cam and crank position to TDC but if go according to the workshop manual, the timing mark on the camshaft is 180deg shifted from the timing mark on the engine.SEE page 2D-6 of workshop manual for hilux models Oct1997 thro

... Toyota Pickup

I have a 2005 Hyundai Tuscani with manual transmission. For the past 3 days my car has continually been jumping into neutral from the 3rd gear up to the 5th (It may also happen some in the 1st & 2nd gears but it is harder to tell). After a few seconds the car will jump back into gear and this continues to happen every 10 seconds or so for the entire time I'm driving. Today the car has actually stalled on me twice as I tried to move forward into 1st gear when having sat at a red light that had

The problem with the transmission is not related to the gas you used. It is mere coincidence that the transmission went out after filling up, if indeed it is the transmission. What exactly is happening? Do the revs suddenly just start picking up as w ... 2005 Hyundai Tiburon

1997 nissan pathfinder timing off. I replaced water pump(behind timing belt). Timing "gears" got moved (two top ones). I don't know how to make sure everything is lined back up correctly.Any ideas?

The cam sprockets should have marks on them (dimples) that should align with marks on the rear timing cover. There should also be a similar dimple on the crankshaft timing sprocket. These will align with their respective marks when the engine is at T ... 1997 Nissan Pathfinder

95 trooper 4x4 check trans light flashing fast trans has been rebuilt was told the trans computer had been replaced trans will manually upshift through 3 gear haven't got o.d. feels like 2 gear is a lil tight or maybe two gears trying to work at the same time but keeps going

... 1995 Isuzu Rodeo

I have a 2002 pt cruiser. I replaced the timing belt and was off one tooth and it started imediately,and ran ok at high speeds, but at idle ran real rough. I once again pulled the belt off and reinstalled it and now when I tried to start the engine and now it will back fire, How can I make sure that the cams and crank are all On TDC, I have a hanes book and lined up all marks as stated, could the crank have been moved 180 degrees? how will I know if the cranks on intake or exhuast stroke? can th

Take spark plug out of # 1 cylinder, and use a compression gauge, and when compression comes up, your on compression stroke, then bring crank pulley to top dead center marks while rotating same direction.Remember, (1) Intake stroke, pist ... Chrysler PT Cruiser

2005 Honda Civic LX, had the timing belt and water pump replaced, about 1 month after the temp started to heat up when idling, never while moving. Found the overflow container full, I replaced the thermostat and the radiator cap. The problem continues, I have noticed that if I keep the rpm under 3000 it will be ok, but if I go over the overflow will start to fill up. Please can someone advise me what to do? Thanks

Are your fans working? If not thats your problem.. I would check your coolant flow make sure your radiator is not clogged and pump is working... ... 2005 Honda Civic
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.8679 seconds