Having problems with your 2003 Hyundai Santa Fe ?

Crank shaft pully fell off

\015 How do i change\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Put it back on
Repair Help & Product Troubleshooting for 2003 Hyundai Santa Fe

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Crank shaft pully fell off


Put it back on ... 2003 Hyundai Santa Fe

How do you remove the front crank shaft pully from a 2003 Hyundai Elantra GT? How do you get the bolt out of the crank shaft pully? Is it right or left handed threads?


It undoes normal way but its tight as its a taper end on crank and no keyway so dont hammer it off with the starter motor and a big bar locked into the suspension.You will have to use a special tool to lock the crank in position ,the other way i do ... Hyundai Motor 2003 Elantra

Water pump when out and I installed a new one then I noticed the small shaft belt was busted so I changed it but when I did I had to remove the crank shaft pully and sprocket and when I did I rotated the crank shaft and when I put everything back together and now my car won't start. I don't know what to do now, what can I do now?


To see if you have spark take spark plug wire off and stick a good screwdriver in the end of the plug wire, hold the screwdriver about 1/2" from a metal part of the engine and then have someone crank the engine over while u watch, if u have spark you ... 1991 Mitsubishi Galant

I have a 2001 ford mustang 3.8l engine with 240,000 miles. we replaced the serpentine belt AND the water pump, a/c compressor, idle pully, tention pully. I still get a loud squeal then the car stalls. Now I cant even get it to start, it cranks but does not turn over. What else could it be, like the crank shaft? (that was my dad's suggestion)


... 2001 Ford Mustang

Crank shaft pully, 1991 s15. 2.5 . Need to replace the timing gears. how do you remove the crank pully mount?


Need a puller check with ur local auto stores some of them loan or let u borrow their tools for free ... 1988 GMC S-15

-the outside ring of my crank shaft pully the part that has the ribs for the belt has slid forward off the center part of the pully how do i fix this it keeps throwing the belt off cause its sitting about an inch further out than the rest of the pullies


Replace the harmonic dampner. ... 1994 Mercury Grand Marquis

Crank shaft pully makes noise


What does it usually cost to replace? ... 2001 Chevrolet Corvette

Crank shaft pully replace


CCW ... Mercury Cars & Trucks

Vw t5 crank shaft pully bolt size 26mm?


... 2003 Volkswagen Eurovan

Antifreeze drips from crank shaft pully area when running.


It's probably not dripping from the crankshaft... it would drip from the water pump just on top of it...to check if it is done, take a flashlight and spot on top of the water pump. there should be a hole on top of it behind the pulley... ... 1986 Acura Integra

How do you fix crank shaft pully on 2005 Kia sorento


... Cars & Trucks

My crank shaft pully has moved forward about a half inch or less does not line up with the ac pully on my 3.4 pontiac grand am any sugestions?


Does it "wobble" around? ... 2000 Pontiac Grand Am GT

Changing timing belt on a kia sportage 2002 having problems keepingthe top two pullys and the bottom crank shaft pully all three in line while putting the belt on. need some advice


... Cars & Trucks

I need to know how to do the timing but i cant get the outer crank shaft pully off is there any markings on the outer pully i could use?


You never have to take the outer pulley off unless you are doing a timing chain. \015\012But I am a little confused because it appears some Subarus use a chain and some use a belt.\015\012And ignition timing seems totally opaque unless y ... 1997 Subaru Outback

Crank shaft pully , ac belt slipped off


The crankshaft pulley is also the harmonic balancer. Price sounds like mostly parts. ... 1993 Eagle Vision

Unable to remove the pullys from the crank shaft


Use a impact wrench. These are very tight from the factory and this is not a at home job. ... 2002 Isuzu Rodeo Sport

1996 mercury villager crank shaft pully nut


... 1996 Mercury Villager

FOR FIXING THE CRANK SHAFT PULLY WHICH BOLT IS FIX SMALL OR BIG


The large bolt holds on the lower crankshaft pulley for timing belt, the six small bolts hold the larger pulley that drive the alternator, power steering etc. It sounds correct. ... 2001 Kia Sportage

Ef ford falcon 1994 tork specification for crank shaft pully nut


As it is difficult to torque set the nut on an assembled engine beacuse you cannot hold the crakshaft, normally if you use a good quality 1/2'' drive torque gun it will be sufficient ... Cars & Trucks

Changed the alternator on 97 nissan maxima and now the cranks shaft pully is shaking and i hear a noise like a rattle or chirping. is it due to the drive belt tension.


No the pulley grooves are a sleeve around the crank. this sleeve will break loose. ... 2001 Nissan Sentra

What is torq spec for 1997 crank shaft pully bolt oh sorry its a montero


2.4ltr = 87 ft lbs, 3.5 ltr = 130-137 ft lbs ... 1998 Mitsubishi Montero

My crank shaft fell off, how do i fix it? - 2002 Kia Sedona


Either the bolts that hold it on have worked lose or broke off, you will have too look at the harmonic balancer too see ... 2002 Kia Sedona

I need to know where the timing marks are on the cams and the crank shaft of a 94 Subaru legacy. The idler pully bearings desolved and I have to replace the belt


Did you look at the harmonic balancer ... 1994 Subaru Legacy Outdoor

How do i get bolt off the crank shaft pully - 1997 Jeep Grand Cherokee


Best sugestion I can give is use an impact gun or take it to a repair shop they can atleast bust it loose for you ... 1997 Jeep Grand Cherokee

My eclipse's drive belt is loose with the tensioner all the way down. I checked new belts and mine is not stretched. Is there a diagram for installing it? The pulley on the crank shaft does not have grooves, not sure if something fell off.


Your belt is not appropriate. try replacing with a shorter belt that fits the groove of the crankshaft and alternator ... 2001 Mitsubishi Eclipse
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.6106 seconds