Having problems with your 2003 Ford Focus ?

Can i just remove the clutch and use the compresor as a pulley

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Without the clutch turned on the pulley is just a idler so you could remove the clutch disc and run it if thats the part that failed
Repair Help & Product Troubleshooting for 2003 Ford Focus

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can i just remove the clutch and use the compresor as a pulley


Without the clutch turned on the pulley is just a idler so you could remove the clutch disc and run it if thats the part that failed ... 2003 Ford Focus

OK, I am trying to remove the water pump on my 97 cougar 3.8 engine. The book states I must remove the power steering pulley to remove the bracket attached to the WP. The shaft that the pulley sets on appears to have a hex (set screw/bolt) holding the pulley on. I have held the pulley in place and used breaker bar in both directions but it doesn't budge. The pulley is plastic so I can not use heat on it. I could use a puller on it if that was the way it is meant to come off, however there


The pulley is pressed on, there is no hex screw retainer, know this for sure, was a Ford dealer tech for 25 years did lots of these, u will need to borrow a power steering pulley puller/installer tool, you can borrow this tool from most auto parts st ... Mercury Cougar

How do i remove the fan and fan clutch from my 1995 jeep grand cherokee? The water pump pulley is pressed on. When I try to turn the big nut, the pulley turns. How do i stop this?


Leave the serpentine belt on. Get a wrench or use a crescent wrench, hit to the left to loosen. It may take a few hits to loosen but will work. If not, use an air hammer. ... 1995 Jeep Grand Cherokee

ANY TIPS ON CRANKSHAFT PULLEY REMOVAL . I HAVE A 2002 SEBRING - 2.4LTR DOHC ENGINE . I'M REPLACING THE TIMING BELT AND NEED TO REMOVE PULLEY . I'M USING A 4" HEAVY DUTY 3 JAW GEAR PULLER . FITS NICE ON PULLEY BUT AM AFRAID IF I GO ANY TIGHTER I MAY DO DAMAGE TO CRANKSHAFT . IT WON'T BUDGE .


... 2002 Chrysler Sebring

One of the three drive belts on my 1986 corolla (4a-c engine) is frayed and needs replacing. The belt loops around the idler pulley, air conditioner? and crank. Can I just cut this belt out and not use my air conditioning? Or if it needs to be replaced, which pulleys/ alternator bolts do I adjust to loosen, remove, and replace the belt properly. I have to remove the main drive belt to remove the one that is frayed. Thanks for any help you can give


To replace the belt you need to see what size socket the tensioner has on the inside. with a ratchet attached put the socket on the inside bolt and push in the rotation to move the spring down taking the tension off of the belt. Pull the belt off a ... 1986 Toyota Corolla 2 Door

The pulley behind the fan clutch has stopped turning causing the belt to tear twice already. My mechanic told me to remove it but in order to do that I need to remove the fan (which I already did) and the fan clutch... I see no bolts or screws on it so I dont know how to remove it.


... BMW 318

I need to replace the bearing on the idler pulley of the a.c clutch assembly and I need to know how to remove the clutch assembly from the idler assembly with the assuption that the idler pully and bad bearing will be removable after the clutch comes off


... Cars & Trucks

I need to remove a water pump to give krager info, so I can get a seal for it.I have removed all the bolts, my only problem in actually taking out the water pump. How do you use the pulley system to r


If its a full Size Bronco,then it should just pull straight off,unless you didnt get the bolts behind the pump pulley. ... 1993 Ford Bronco

I am replacing the water pump on my 1996 Isuzu Rodeo. One of the water pump bolts is under the lower timing belt cover. However, the lower timing belt cover appears to connect around the crank shaft behind the three lower pulleys. How do I remove the pulleys so that I can remove the lower timing belt cover? What size and type wrench should I use? Thanks, Ralph


Hello Ralph,\012\012What you actually going to have to do is take both timings covers off eventually. The waterpump is driven by the timing belt, and will have to be removed along with various other components. \012\012The pul ... 1996 Isuzu Rodeo

I believe the bearing on my waterpump is bad. while driving the fan began rubbing the shroud and eventually wedged against the waterpump pulley. before removing the radiator,shroud and hoses i checked waterpump pulley and could move it up and down. how do i remove the waterpump. with the fan and fan clutch still attached


You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off ... 1999 Ford Ranger SuperCab

Cannot remove a/c clutch to remove shim. tried screwdrivers but worry about breakage. can i use penetrating oil? 1998 nissan frontier,198000 mi. works fine if you tap the clutch in with screwdriver. the clearance is .040


They are pressed on and you need a ac clutch removel tool to remove them so you dont damage the clutch . you can buy the tool on ebay or check www.harborfreight.com about 50-89 dollars ... 1998 Nissan Frontier

I replaced the clutch disc,pressure plate and throughout bearing,also resurfaced flywheel. Replaced clutch master/slave unit The problem is it seems that the clutch is partially engaged.When the car is running you can put the car in gear without depressing the clutch. (it does it with the master/slave assembly removed also )using a rod and long pry bar I can push on the clutch fork.It seems to release.Help. Can it be a bent fork?Throughout bearing off?


You could have put the clutch plate in backwards. ... 2001 Saturn S-Series

2002 Nissan XTerra Main Pulley removal, screw size use screw into pulley with pulley puller


Excuse me fore' I thought this was a free service, I will not need the paid assistance at this time ... 2002 Nissan Xterra

1990 bmw 535i ive been trying to remove the nut between the fan and pulley that attach to water pump, is there any special tool to loose the big nut from water pump. ive used chain against the pulley but the big nut just keep turning. ALSO im afraid i might brake the pulley. the water pump is leaking.


There are special wrenches for this. One will slide over the 4 bolts that hold the pulley on and the other you use over the big nut. A lot of parts houses now loan tools. Try one in your area and it will make quick work of this. Now, when you go to i ... BMW 525

How do I remove the a/c compressor clutch and pulley for a 1997 Mitsubishi


A special tool kit is required to pull it off. ... 1997 Mitsubishi Montero Sport

How do I remove the pulley connected to the fan clutch on a 1995 jeep grand Cherokee? But the pulley just turns with the fan in both directions.


You need a special tool to loosen the large nut that takes off the fan clutch the right I use a large punch and a hammer to drive my loose on the same part except it is a dodge Dakota. Using the punch method can damage the water pump front bearing so ... Cars & Trucks

I have a 1975 Pontiac Firebird 350V8 with air. I bought it used and the A/C clutch needed replaced. I did that, and now it seems like excessive whirring noise at higher speeds and belt slop. I looked and it seems there once was a belt tensioner or pulley next to the water pump. Was there a pulley for the A/C belt on this engine?


... Pontiac Firebird

Ive got an audi a4 2.4 v6 and want to change the cambelt. do i have to use a locking tool or can i put my own marks on the cam pulley and crank pulley before i remove it???


They have marks on them already,highlight them with chalk. ... 2004 Audi A4

How do you rerout the belt on a 1994 buick roadmaster estate wagon when not using a c pulley...The ac pulley and clutch has seized up.


You will need to get an idle pully, remove the air con. pump and fit the idle pully in its place. You may be able to reroute the belt but getting a belt to fit will be a problem. ... 1994 Buick Roadmaster

1994 buick lesabre 49k, ac working o.k....clutch pulley rubbing on bracket...a/c on or off..makes no difference, belt worn from pulley migration, easy fix on car without removing lines?


Yep you can loosen off the the whole compressor unit from the bracket and hold it away from where you'll be working without disconnecting the high or low pressure line...Just be careful and tie the unit in a safe place while you're working...It'll be ... Buick LeSabre

I need to replace the cam pulley that drives the water pump belt on a 1997 deville is this pully pressed on do I use a pulley puller to remove it?


If there is a dimple in the middle of the shaft, then you will probably need a pulley remover. make sure you havent missed any bolts that you have to go through little holes on the pulley to get to also. and also turn the pulley and look for any bolt ... 1994 Cadillac DeVille

Trying to replace the master clutch cylinder on a 1979 280zx. Having trouble removing the flare nut on the clutch piping to the master cylinder housing. It won't budge. Don't want to round it off, have used liquid wrench with no results. Doesn't seem to be corroded. Any tricks? Thanks for your help.


280zx -- one of my favorites,, I have owned a few,,, the best trick to loosening I have found is to use a little heat on the fitting ( heat gun or propane torch ). note: always be careful and mindful when using the propane torch as open flames in or ... 1984 Nissan 300ZX

2002 CHRYSLER SEBRING - 2.4LTR DOHC ENGINE I AM INSTALLING NEW TIMING BELT . I AM HAVING TROUBLE REMOVING THE CRANKSHAFT PULLEY . I'M USING A 4" HEAVY DUTY 3 JAW GEAR PULLER AND CAN'T GET THE PULLEY TO BUDGE AND AM AFRAID IF I TIGHTEN ANY HARDER I'LL DO DAMAGE TO CRANKSHAFT . ANY TIPS


There on very tight, did you insert a bolt in the hole, where the bolt for the crank bolt goes on, insert a long where it sticks out pass the pulley about 3 to 4 inches, but thinner bolt in there, and the tip of the puller on it, tighten the puller, ... 2002 Chrysler Sebring

Need exact procedure for removing the fan and clutch fan pieces so that I can remove the water pump. There must be one more thing to loosen besides the four bolts (13mm) on the fan blades and the four bolts (10mm) on the smooth belt pulley that attachs to the front of the pump. What am I missing? 5.7 Vortec with AC.


Leave the fan belt in place and it will hold the pulley and fan in so you are able to remove the large nut that is behind the fan ... 1998 Chevrolet Tahoe

The ac pulley on my 98 plymouth voyager 3.3 v6 started grinding and smoking bad i would like to remove the ac and use a replacement puley, and have know idea how till i can aford to replace ac or fix.


... 1998 Plymouth Voyager
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.8174 seconds