Having problems with your 2002 Toyota Camry ?

I just replaced me battery and ports, then I replaced the alternator. My car still won't stay running even in gear unless I have my foot on the throttle. What else could it be? Fuel dilivery problem??

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Throtlle position senser faulty.Only solution is to change it.
Repair Help & Product Troubleshooting for 2002 Toyota Camry

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just replaced me battery and ports, then I replaced the alternator. My car still won't stay running even in gear unless I have my foot on the throttle. What else could it be? Fuel dilivery problem??


Throtlle position senser faulty.Only solution is to change it. ... 2002 Toyota Camry

Idle Hi, I own a non Turbo 87 rx7. The other day it was running fine, than after i got gas and start it back up, it won't idle unless i keep my foot on the gas pedal, and accelerator is extremely slow, I just replaced the fuel filter, fuel pump. fuel pressure regulator. What else could this problem be? Thanks


May have pic,up water at the gas station ,put a bottleof water absorber like (heat) that will absorb the water ... 1987 Mazda RX-7

'90 F-150 with 5.8 engine acting like no fuel to keep engine running. have replaced distributor cap and double checked the fuel shut off valve located underneath the foot petal and still acts like not not wanting to turn over. I have added Lucas fuel injection cleaner two previous fill ups including this time and now the problem exits. what could the problem be and what else needs to be replaced?


Check you fuel pressure at the fuel rail, if you have pressure (witch i doubt) then look at injectors, otherwise start with the cheap stuff and work up to others, start with a fuel filter and if that dont help look at a in tank pump or the high press ... 1990 Ford F150

Hello there, i have a 2000 impala 3.8 v6 series2 engine and the code p0300 keeps showing up on the code scanner...i replaced the plugs, wires, intake manifold and gasket for it, tubings/vacuum lines checked all sensorson the throttle body, replaced egr gasket, coil packs,fuel filter,fuel pump is still good,and the hose and pcv valve was also good wat else could be the problem?? i replaced the o-rings on injectors but not the injector wasnt checked.. i haven checked because i spent enough cash on


The error code Stands for: random/multiple cylinder misfire detected. sounds like you just forgot to reset the error code once you repaired the issue.... hmmm, A P0300 OBD code indicates a random or multiple misfire. If the last \015\012 ... Chevrolet Impala

My 93 gmc sierra would start but when i put it in gear and tried to accelerate it would act like it wasn't getting gas. I used a diagnostic tool and it said there was a problem with the map sensor i replaced it and now the truck wont start at all. so we took apart the throttle body and found that the fuel pressure was really low but its not the fuel filter. Is there anything else I could do besides replacing the fuel pump.


It sounds like your fuel pump has failed. Use a fuel pressure gauge to see what your pressure is now. Once you've replaced the fuel pump you will see the difference in the pressure and it will repair your concern. ... GMC Sierra 1500

Won't start unless you push pedal to floor and then it will not stay running unless keep foot on gas. Have replaced plugs, wires, distributor, and pcv valve. Could this be a problem with fuel filter or fuel pump? Desperately need answer, this truck is my only transportation. Thanks


It sounds like fuel pump is going. pressure should be around 40 psi.Or it could be flooding. Holding gas pedal to floor during cranking of the engine, shuts off fuel flow through the injectors to clear a flooded engine. After engine is runnin ... 1989 Ford F 150

I have a 1995 Ford Thunderbird 4.6L V8. The problem I am having is that at times I will be stopped at idle and the engine will suddenly quit on me. The car is on drive and my foot was on the brake pedal. I have already cleaned the MAF with the prescribed electrical spray cleaner. I have also replaced the Air Intake Sensor with a new one. I'm about to replace the air and fuel filters. What else could be the problem?


Check you vacuum ... 1995 Ford Thunderbird

I have a 1989 chevy caprice wit a fuel injected 350. I replaced the fuel pump and the fuel pump relay. I also changed every fuse in the inside of the car. I have gas coming up to my throttle body. But the car won't unless I spray carb cleaner in it. And it doesnt crank everytime.. But it runs a while then kills. But while its run'n I don't see any gas shooting out of the injectors. What could be my problem??


The injectors on a TBI are going to spray gas only when the engine cranks over not when the key is turned on. With that said you may have a bad pressure regulator in the TBI. The rubber in it may have a hole in it not allowing it to build pressure f ... 1989 Chevrolet Caprice

I bought this car with a bad motor. replaced the motor with a good one,it runs good when its cold but once drive it 40,50 miles sometimes less, it will stall an will not start back up, until it has set for 1 to 2 hours. i thought it might be a fuel problem, because when it wasnt starting i poured some fuel into throttle body an it started until fuel was gone from throttle body i replaced fuel pump an fuel filter an it still has same problem. do you think it could be the fuel injector. thank


It may be but try replacing the relay for the fuel pump. it is located in the engine compartment near the battery. you should find a fuse box there. also when the engine quits... listen to see if the fuel pump is working. if so that will rule out ... Geo Metro

1999 Pontiac Montana ran out of gas. Now it will not start. It was suggested I try replacing the fuel filter, which was due to be done anyway. Although this did not fix my problem, I noticed that the fuel line between the tank and the filter was dry, even though the tank was now filled with gasoline. Does this mean that my problem is the fuel Pump? If not, what else could it be? What's the easiest way to replace the fuel pump... Could I do this repair easily myself, or should I have it tow


2 major problems can occur when you run out of gas. The first is that alls those horrible bits of gunk that have been floating around in the fuel tank since it was new, get dragged into the tank outlet! The second is that the pump runs "dry", which i ... 1999 Pontiac Montana

Have a problem with not being able to accelerate. Had to recently replace starter and alternator and thermostat. After thermostat car started bogging down when we tried to accelerate. Replaced fuel filter and checked fuel pressure. Fuel pressure reads 50 lbs at idle and 60 lbs with car in gear, foot on brake and giving it gas. Could get car to about 40 mph but took about 1/8 mile to do it. Was going to replace fuel pump, but was told that is not the problem. Car doesn't shift hard so I don't thi


I don't know who is doing your auto diagnostics,but I can't quess at what is left to check, without the vehicle. Any repair shop should be able to solve your issues, fairly easy.\015\012Was the converter checked for deteriation or blockage. If ... 2002 Chevrolet Malibu

Problems with my 97 Honda CRV. Erratic idle, stalls when coming to a stop. Replaced fuel filter, ignition coil, I don't know what else it could be. Possibly carbon deposits in throttle body iac maybe. Any ideas?


It could be the main relay and/or the ecm. Or it could be the distributor timing off.Could be the ignition switch. Honda issued a recall on 1997 CRV ignitions in 2002. \015\012Go to www.ahm-ownerlink.com and under quick tasks, cli ... 1997 Honda CR-V

I have a 560sel that is very hard to start when warm after sitting for a few minutes, the primary fuel pressure holds overnight, but I noticed that the fuel distributor was leaking fuel into the throttle body at rest so I replaced the fuel dist. with a rebuilt unit and it does the same thing, almost all the components have been replaced. Did I get a bad dist or could it be something else. The only way that the car will start warm is by holding the throttle to the floor while cranking for a long


The black smoke is a sign of running rich, so chances are your car is still leaking fuel into the throttle body and the startup is especially rich. The injector itself (at the throttle body) is a likely culprit - if the pintle is leaking, or the O-r ... Mercedes-Benz 560-Series

I have a 93 dakota and when i am driving it will shut down all of a sudden and the fuel pump will not kick back on i have replaced the fuel pump relay and the auto shut off relay and truck still will mot start i have also replaced the fuel pump and i have electricity going to the pump. Is there any thing else i am missing? Could this problem be a ecm problem as well?


Perform a fuel pressure test. Take the cap off and install a fuel-pressure tester. Turn the key on and check the pressure. It should be 49 psi. If there is pressure, the problem is elsewhere. Disconnect the fuel-pump harness, which is located on the ... Cars & Trucks

1985 BMW I535 starts but will not pick up power..like gas is not getting to anything.changed out fuel pump#2, changed filters, flushed fuel ejectors with cleaning additive, replace battery and starter. replaced fuel filter..I do not know what to do next. Will replace the pump inside of the tank..but wondering if this do not fix problem what else could it be. I cannot not go up past 30mph...and the engine is running strong. Any help will be appreciated.


... BMW 535

I have a 1999 F-150 5.4 Lariat 4X4. When declerating, when I get between 45-55 mph it loses power or fuel then picks back up when applying the pedal. Could this be a throttle sensor problem or fuel pump problem? I replaced the fuel pump about 8 months ago (20,000 miles). Note: This problem only seems to occur when it has been driven a while at 55+ mph.


... Ford F-150

I have a 96 chev blazer it had a leaky fuel line i replaced it it fixed the problem , after a few months it wouldnt start so i sprayed starting fluid and it got me 60 miles now wont start i replaced fuel pump, fuel pressure regulator checked relays still has spark n suffecient fuel pressure up to the injectors but injectors are not spraying fuel what else could i do?


SCAN IT FOR CRANKSHAFT SENSOR PROBLEMS AND PCM PROBLEMS.CHECK THE ECM FUSES THEY ARE 20 AMPS.CHECK ALL IGNITION AND ECM FUSES THEY ARE 20 AMP FUSES.LOOK FOR BLOWN 20 AMP FUSES. ... 1996 Chevrolet Blazer

I have a Mercedes C180 that was constantly going into limp mode. I'd turn the engine off and restart the engine and everything would be fine for a while and then it would go back into limp mode. So I decided that I would replace the fuel filter to see if this was the problem. Unsure as to whether or not it has fixed the limp mode problem as I have an acceleration problem. The car seems to idle okay but when I put my foot on the accelerator the engine surges. Could this be a fuel pressure problem


You need obligatory to access the Engine Control Module (ECM) using suitable diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored. Then you will be full informed abou ... Mercedes-Benz C-Class

I have a 1997 chevrolet lumina sedan with a 3.1 engine. had a problem with a loose spark plug wire and replaced a bad throttle position sensor. a few days later the car would run well then not start. replaced fuel pump with used pump. now the pump runs and the engine gets spark and vaccum but will not start unless you spray fuel directly into the intake. the fuel pump will only run when you bypass the fuel pump relay hot to hot. ive been told it maybe a bad cam shaft or crank shaft sensor. does


Then u have no injector operation, check for blown fuses under the hood, look at ECM fuses, there are 2 i believe.. ... 1997 Chevrolet Lumina

I have a 90 GMC Sierra, 5.7 ltr, 2 wheel drive, 1/2 ton. I recently replaced the ESC module ,MAP sensor, and TPS, because they coded out... I also replaced the distibutor as well. I was running well this morning and sat at idle for a couple of minutes in park. As soon as I placed the truck in drive my motor died never to return again. I have spark, I have fuel pump - on, I replaced fuel filter now. It cranks and sputters but won't run? What else could it be? Would throttle postion sensor do


Try spraying a couple shots of carb spray down the throttle body while a helper cranks it over. If it starts and runs for a couple of seconds check fuel pressure and the resistance of the injectors. ... 1990 GMC Sierra

Fuel supply the problem I'm having is, the truck will not start unless I pour gas into the throttle body. then it runs fine.what could cause this problem/ I'm getting good fuel pressure to the intake. relaced the fuel pump and filter.


Sounds like there is no power to the fuel pump while cranking. check the oil pressure sender this helps the fuel pump run under cranking ... 1998 Chevrolet Tahoe

1993 jeep wrangler 4.0. Jeep stalls when accelerator is slightly engaged. sometimes hard to start after this. sometimes starts right up. already replaced crank position sensor. What else could be wrong? Auto shop at school cleaned plugs and dumped fuel injector cleaner in tank. Fuel pressure on gage reads 30 psi then increases to about 40 psi when vacuum line is removed from fuel pressure regulator. Could the problem be the TPS? or cam sensor?


The fuel pressure you listed is to low,The regulator should keep the pressure down to at least 45psi,removing the vacuum from the regulator it should spike to at least 55-60.Did it start and run better with the hose off?replace the ... 1993 Jeep Grand Cherokee

1985 Volvo 740 GLE non turbo.. Will run for a while then stall. Have replaced the plugs, wires, distributor and rotor and timing belt. What else could be the problem.. Can it be the fuel pump relay or fuel pump? It ran fine until plugs were replaced.


... 1985 Volvo 740

I have a 1990 corvette coupe with the l98 , I have replaced the fuel injectors , cap and rotor, plugs and wires, temp controll sencor , idle control sencer, o2 sencor , ecm computer, fuel regulator and my car still runs like ****. It does ok untill I give it a lot of throttle then it bogs down. Could this be a vacuum leake? If so how can I find that leake? Is there a diagram telling you where each line should go? Or what else could it be?


Check timing chain. Shoot a timing light at the crank, and see if the mark is jumping around, or staying in one spot. If it's jumping, time to change it. It probably jumped a cog. If it's a vacuum leak, wiggle the hoses around with it running, and li ... Chevrolet Corvette

My 2006 Ford Expedition runs perfectly however; when I step on the accelerator and push it to the floor regardless of the current speed or from a complete stop, it appears to be slugish and begins to ****. What could the problem? Note: Fuel filter was replaced less than a year ago by Ford as part of preventive maintenance. Subsequent to vehicle going into failsafe mode, Ford also replaced throttle body and motor assembly as well as sensor relay and reprogrammed PCM for $850.00. Could t


Sounds like one of the ignition coils are bad. ... 2006 Ford Expedition
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.4466 seconds