Having problems with your 2002 Suzuki Grand Vitara ?

Where is the thermostat housed in a gran vitara 2002 petrol

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Inside the housing that the BOTTOM hose goes onto. I assume you have a 2L 4 cyl or 2.5L V6 petrol version. I don't know about the TDi (if available).
Repair Help & Product Troubleshooting for 2002 Suzuki Grand Vitara

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where is the thermostat housed in a gran vitara 2002 petrol

Inside the housing that the BOTTOM hose goes onto. I assume you have a 2L 4 cyl or 2.5L V6 petrol version. I don't know about the TDi (if available). ... 2002 Suzuki Grand Vitara

Torque wrench settings for ford focus thermostat housing on 2001 1.8l petrol engine ( 3 x bolts)

There is a set spec, but for the DIY mechanic,,\015\012Using a !/4 " drive, with the correct long socket, apply a FIRM effort on the wrench, but obviously not too much, as to sheer the studs. Always use a NEW gasket on all mating surfaces. ... 2001 Ford Focus

Thermostat housing gasket leaking coolant 2004 mercury gran marquis

... 2000 Mercury Grand Marquis

Heating problem I recently purchased a 6 cylinder toyota petrol motor after running for about 15-20 minutes the machine starts to run very hot ! I left the radiator cap of and dirty rusty looking water came out of the top (obviously very dirt water and need good flush out I took the themostat housing apart (no thermostat inside ?) do you think I should put one back in? also do you think that once I clean system ( flush radiator and engine block out ) my heating problem should be sloved ? No ob

Milky oil means water is mixing with it might be a gasket ... Cars & Trucks

Can't get to thermostat because the crossover exhaust pipe is blocking it.Can't figure out how to take it off.Can't get to bottom screw of the thermostat housing because of this pipe. This is a 2001 aztek the crossover exhaust pipe is so close to the thermostat housing that you can't t get to the second bolt to take the housing for the thermostat off to get to the thermostat.Need help to take off crossover exhaust pipe.

Had this problem once mine was 13mm bolt. I took an old wrench heated it with a torch and bent it just the right angle. worked perfect. ... 2001 Pontiac Aztek

I have removed the thermostat housing and can see the thermostat. it is inside the housing. does the plastic housing come apart. I'm afraid to put too much force without knowing for sure. I was sold a replacment thermostat so i am thinking the housing should come apart. thanks for your help Dave


6.5 Diesel Thermostat Housing Bolt Access: Gentlemen, I have marveled at the idiocy of the alternator bracket housing, cursed long and loud over the near psychosis of the water pump mounting, and have detoured into the perplexing case of the gigantic Torx bolt on the belt tensioner. I am now faced with the lower bolts on the dual thermostat housing. How, pray tell, does one remove these hidden treasures. I am but a simple shade tree novice, raised on the silly old 2 bolt thermostat housing.

GM Full-Size Trucks 1988-1998 Repair Information\015\012Thermostat - REMOVAL & INSTALLATIONDiesel Engines1988-95 models\015\012\015\012\015\012\015\012 ... GMC K1500

I have a thermostat housing leak in my 2000 MY01 Subaru forester, 2.0lt model, just wondering if anyone knows how much it is to replace the whole thermostat housing or just to re-seal the housing...? I seem to be going through half a bottle of coolant in a week. Pretty sure it's just the seal/gasket on the housing that's buggered, not the actual thermostat, any help would be appreciated. Cheers :)

... 2000 Subaru Forester

I am replaceing the thermostat and the thermostat housing on my 1993 jeep cherokee sport. when i get the thermostat housing tight and everything hooked up in pours coolant out the botton of the seal on the housing. what is the problem?

You did not seat the thermostat correctly. it is off center on the gasket. ... 1993 Jeep Grand Cherokee

I plan to replace the Thermostat housing when replacing the thermostat and upper radiator hose. Questions: - Should sealant be used between the thermostat housing o-ring and the engine sealing surface? If so please advise type and brand name. - Initially I planned to flust the cooling system but reading about air-lock problems decided not to do this myself. Knowing there will be some collant loss when replacing the upper radiator hose and thermostat, I plan to attach the new hose to the replaced

No sealant should be needed.clean both surfaces well.be sure 'o' ring stays in place & thermostat is installed correctly.you'll probably only fill the hose as the thermostat will be closed,but that won't hurt.keep proper level in over flow tank,i ... 2001 Ford Focus

I have a 1994 ford e350 cargo van 5.8. my radiator is leaking around the top not the cap i've changed my thermostat and thermostat housing water pump hose upper radiator hose and radiator cap and now it seems like coolant is leaking around the end of the radiator hose thats on the thermostat housing .any idea of what it may be ?

... Cars & Trucks

I can't get the thermostat housing off the engine to replace the thermostat. i've removed the bolts, upper radiator clamp and hose from the elbow going to the housing and it is loose, but it wo'n tcome off because ther is another tube going back towards the engine on the bottom of the housing. what do i do?

The thermostat is not under the upper housing. The thermostat is behind the lower housing that the lower hose is connected to.If you are changing the upper housing known as the water outlet housing because it is leaking you are on the rig ... 2003 Dodge Intrepid

The thermostat housing separated, or blew apart would be a better way of putting it. Im sure it needs a new housing but I cant figure out how to put a new thermostat into the new housing. This is a 2005 chevy aveo ls

This is a notorious Aveo problem, These are poorly made.You need a new thermostat housing it includes the thermost on the 04-05' Aveo. It is all one sealed part from the factory.The original part is made of plastic. Chevy has an aluminum one now that ... 2005 Chevrolet Aveo

What is the proper procedure for replacing the thermostat housing, thermostat and gasket on a 2001 Ford Explorer Sport Trac with a 6 cylinder engine? The Ford dealership said the housing is leaking and that it is a common repair for this motor, to replace the housing and gasket.

Hi, to replace the thermostat housing, thermostat and gasket, follow the detailed instruction below on how to do it.\015\012\015\012\015\012\015\012\015\012Remove the thermostat housing from the engine block of ... Ford Explorer Sport Trac

What is the part under the thermostat housing called? the part that the thermostat housing bolts on to? It is black plastic and seems to raise the thermostat up higher.

The adapter housing ... 1999 Mercury Cougar

Thermostat housing can the housing on the block side of the thermostat housing be fixed

Yes it can however depending on the type of metal your block is made out of depends on weather it can be fixed in sum cases you can just weld the broken block but your engine block may have to be taken off to do the job speak to your local engineers ... 1989 Nissan Maxima

Just changed waterpump in our 1997 Elantra, has 147,400 miles also changed timing belt and thermostat and thermostat housing gasket where heater hoses are. New antifreeze, was running engine and checking the heat to make sure thermostat was working. Then we noticed a water leak, so we changed the thermo gasket and housing gaskets again. Again we were running the engine while we were installing the antifreeze again. While running the engine after a few minutes we noticed again water was leaking,

Check the oil stick if their is a milky like substance on it if so the the block could be cracked. i hope not. The mechanic should've notice this if thats the problem. do check plug also. H.I.W.H ... 1997 Hyundai Elantra

How do u change the thermostat housing on the f150?? its a 93 straight 6..buddy broke the housing changing the thermostat and cant get the housing off to change it

This simply requires removal of hose and both attatching bolts of the housing to the block...restart all bolts by hand until properly started ... 1993 Ford F150 SuperCab

On a 2004 suzuki forenza, my check engine light turned on, and I got an error coded saying it was the thermostat. Would I have to purchase the entire housing that has the thermostat already attached? Or can I remove the housing and replace just the thermostat itself?

Not sure here on model but i think it comes with the housing all in one ... 2004 Suzuki Forenza

Can i use gaskett sealer to re-seal the blown gaskett on my 2005 explorer advanced trac 4.0 sohc lower thermostat housing? my thermostat stuck and wouldnt open so it blew the lower plastic thermostat housing seal can i take that apart and reseal it with gaskett sealer?

No, there is most likely an o ring in there ... 1999 Ford Explorer

I have a 2000 Ford Explorer and it keeps wamting to overheat ive replaced thermostat and the thermostat housing all brand new and the sensors in the housing it all came new and its not leaking out the over flow bottle is boiling when stop to let cool off oh and i replaced the rad cap as well any info would be great thanks

Your fan clutch could be bad. ... 2002 Ford Explorer

2002 Astro van. Will not start. Getting fuel, distributor changed. Had a little accident while removing the thermostat housing. A ground snapped. Two wires. Black/white and Tan/white. I know the tan/white is a ground for the ecu. But I do not know what the black and white ground is from. Also when attempting to crank. Pressure is building and shooting through the thermostat housing. Bubbles form or a spray of fluid. No idea what the black/white ground that was attached to the thermost

Its a temperature sensor thats connected to a pop off valve its usually in the main wiring harness 16 to 14 guage wire should be sufficient for the repair and make sure u have splice connectors black tape corrodes quickly and could lead to other cost ... 2002 Chevrolet Astro

Thermostat Housing Looking for a thermostat housing for a 1984 Mustang, 3.8 litre engine. Cant find one anywhere

Try a salvage yard, or an automobile radiator repair shop. They should definitely be able to point you in the right direction if they don't have one to sell you. ... 1984 Ford Mustang

My 89 Pulsar,Vector (auto) has been off the road for around 6yrs due to an accident & being unable to afford the repairs.This year i was able to get it back on the road but during warm weather my car overheats ALOT. Im assuming it could be the thermostat not opening properly due to how long it sat there & have purchased a new one (also the housing because it is corroded.Im hoping that will fix the problem..I would like to know how to install the thermostat & housing myself.Also I have noticed th

It needs a little TLC after sitting so long , you need a good fuel additive maybe even drain the tank and refill it (fuel) also the cooling system might need a little more then just a T-stat it might be helpfull to have it drained and flushed , but t ... 1989 Nissan Pulsar

Thermostat was stuck closed, and i replaced it, but i can not get the housing seated properly when i tighten the bolts. the engine is a 1999 chrysler concorde 3.2L. how do i get the thermostat to stay seated when o put the housing back against the block

Does the thermostat match up with the old one? Was it installed the correct way facing upward? ... 1999 Chrysler Concorde
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7332 seconds