Having problems with your 2002 Mercury Cougar ?

Hot wire my 91couger to start

\015 How to hot wire to start with out key\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

There is no way to wire around the powertrain control module.
Repair Help & Product Troubleshooting for 2002 Mercury Cougar

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hot wire my 91couger to start


There is no way to wire around the powertrain control module. ... 2002 Mercury Cougar

I just bought a 2000 ford taurus. It would not start or crank over.I noticed the ign.key had a lincoln key logo. I bought a new pats taurus key. It still did'nt turn over. A ngs was hooked up to the dlc connector and data link diagnois results showed 914,915,pcm no response or communication.I started checking out the starting system. Check out the starter relay and wiring. I have power to the relay at the Lg/vt wire all the time,the 15amp fuse is hot and the Tn/rd wire is hot in the start mode.


At the base of your steering column is the ignition/start/run switch. This has failed and needs to be replaced. You'll need to drop the column and remove the kneepad to gain access. Be sure to locate the new switch in the exact spot of the old one. I ... Ford Taurus

I have three wires that run form the battery down to the starter. I need to know where they are attached to the starter.I don't want to burn starter. When I attempted to start vehicle, the starter and hot wire got hot and I only heard the starter spin and not start. 2006 chevy malibu Is there a schematic that can assist I connect the right wired to the right place?


Your positive the red wire goes on the big bolt of your starter - You should have two smaller wires - One is from the distributor and the other is from the igniton. Hook these two wires up the same way you took it off. If you are not sure of how the ... 2006 Chevrolet Malibu

Im working on a 1986 toyota pickup 2.4l efi non turbo 4x4 i replaced the head gasket and i have a black wire coming from the intake wiring harness that has no plug on it .if i touch this wire to a hot wire the fuel pump relay will click and the injectors will make a sound if i put a jumper wire on the fuel pump test plug and then touch this wire to a hot only the injectors will make a noise i understand why this happens but i need to know where this wire goes the truck wont start and run it turn


Sounds like this wire should operate the electric fuel pump through the fuel pump relay.The fuel pump relay should start the fuel pump to maintain fuel supply to the common fuel rail and any surplus fuel will be bleed back to tank by pressure contro ... 1986 Toyota Pickup 4WD

I have a 91 Cadillac Deville that will not start. It does not crank or even try to start. A while ago, I ran the battery down, and then was able to jump it and it ran fine. Then, I left the lights on after a drizzle, and could not get the car to jump. I had a mechanic hot wire my starter from my battery after charging it, which caused the solenoid to engage, but the car would immediately die as soon as he removed the hot wire. Now, after replacing the battery, the car still does not even tr


Try turning the key to the on position and wait for the security light to stop flashing (usually ten or fifteen minutes) then turn the key off and try to start it. On some you need to do that procedure three times without starting but most will re-st ... 1991 Cadillac DeVille

I have a 83 280zx non-turbo which quit running. Heard pulsating noise at fuel pump relay (kicking in and out) under dash passenger side. Replaced relay, still does same thing. Replaced water temperature sensor, pulsating goes away but relay kicks out almost immediately. Can hot wire fuel pump to get it to start but this method is not very safe. Is fuel pump bad or do i need to look someplace else. I have been able to hot wire fuel pump briefly to get started and then car will run on its own


... 1983 Nissan 280ZX

For a couple months now when starting the car i would have to turn the key a couple times before the starter would engage. the first couple turns it would just clack. Then i went to start it tonight and the starter just kept running. even with the key off. i had to pull the negative wire off the battery to get it to stop.i managed to take the hot wire to the starter off, reinstall both battery cables, put the key back then turn the ignician on and touch the starter cable to the hot post of the


It may be the relay. The relay can make a clicking noise. But, if your ignition is sticking, it may do this as well. You really need to check them all. If you turned it off and the car kept running, you have a bad ignition switch. You can try hitting ... 1999 Toyota Camry

92 grand marquis i have 1 wire and fuse that keeps gettin hot and the fuse keeps blowin. the wire has melted down into where it connects to the back of the fuse box. It get very, very hot at the connection spot and then the fuse get hot and start melting also. only abouy 2 inches of the wire has melted. what do i need to do???


You have a slow short in system this can cause a fire you need to determine what circuit it is and check for either a defective part also bad electrical connection you will need to possibly replace the wire or insulate it after cause is found ... 1992 Mercury Grand Marquis

I have a 95 Camry 4 cyl. I had the Distributor changed last year along with the timing belt, plugs, wires, and fuel filter. Now when I drive it goes about 7 miles and shuts down, after about an hour it will start and run for about another 5 mins then die again, I tested the wires going into the fuel pump and one of the main wires loses it's fire when the car stops, I ran a hot wire from the battery to that wire and can hear the fuel pump running, got it started again, put a finger on the fuel pu


Lets start at the beginning. The engine computer grounds the pump relay. The relay gets power from the EFI relay when the key switch is on and from the starter fuse when the key switch is in the start position. Do you know if the pump relay is get ... 2000 Toyota Camry

I had the same problem, all u do is take apart the box behind the steering wheel, unplug the cluster of wires look to see if the plastic has melted, find out which wire runs the tails and dash, take that wire and hard wire it into the ignition. now the lights come on as soon as u start the car. this is a comun neon problem i now leave the box appart becase if u drive around with it off and feel the wires they get REALLY hot, so imagine how hot they become inclosed in the box, anyways hope this h


... Chrysler Neon

Stalls when hot,turn but won't start until it's cold. it started that the engine would miss once in a while around 50mph. then it would not start at some occasion would shake the wires and it would start soemetimes. Timing belt,plugs.wiring ,all ignition components(cap.dist even the stutor)change. last thing i tried was to unplug the o2 censor no different when it got hot engine died,black smoke in the back and smells gas (too rich) no check engine light on,


Change air temp switch. ... 1990 Dodge Shadow

I have a 1987 chevrolet celebrity. A rabbit got into the engine compartment and chewed all of my spark plug wires, the wires on the distrubitor's wiring harness, and a couple others. I've reconnected all the wires properly and am getting spark from the spark plugs but it's not getting gas and won't start without starting fluid sprayed. No power to fuel injector intake, and the computer is not running hot. If someone could help me out, I'd appreciate it. I've checked the 4 fusible links in th


Hi, are you sure your fuel pump is running? I'm assuming you have the 4-cylinder 2.5 liter engine. The ECU and the injector are powered by the same wire as the ignition system. See diagram below. ... 1987 Chevrolet Celebrity

I need a diagram of a 2002 2.2 chevy cavalier starter my starter wont start i have the ground wire in place and the large red hot wire i also have a smaller red hot wire that is not hooked up to a stud of any kind and i can not for the life of me see another stud or what ever it is that i need to hook this third wire to. please help if you can thanks


That sounds like the wire that should go to the solenoid to activate it and also engage the starter.\012\012It should be the "S" M8 terminal.\012\012 ... Chevrolet Cavalier

My 2002 elantra has no fuel,changed fuel pump still no start,theres 5 wires on the pump,two grounds are good,a wire get hot with the key,theres a red wire that does nothing,should it get hot when cranking


Remove the pump and check out the sender /pump unit ,could be the insulationon the wires has burnt off and the wires are shorting ,THIS IS DANGEROUS AND THE VEHICLE COULD CATCH FIRE , ... Hyundai Motor 2002 Elantra

99 Silverado 4.8 Starts good cold (open loop) Starts very hard when hot, during hot soak. Turns over excessively long before startup. Also at times sets a PO300 multible skip, and starts dropping cylinders. Oddly, mostly on even cyls. Have replaced camshaft, & crankshaft sensors, plugs, plug wires, and checked all coils, all read same resistance. I have Snap-On scanner, and all sensors read ok.


I'd change the coolant temperature sensor. At different engine temperatures, the parameters for starting the engine are different (fuel mixture, ignition timing, etc), and if the coolant temp sensor is out of whack, the ECU won't set up properly to ... 1999 Chevrolet Silverado 1500

1976 mgb w/cat converter please help- day 2 after changing to a new coil adn starter and i cannot get it to start -the last time ti tried- the starter got hot but still no start when i turned the key. i need to verify the coil and starter wiring i assume these are right- coil- green white to positive and blue resistor to positive and ground coil- white/ black to negative and brown wire to I think a ballast for the distributor wiring system starter -big battery positive to lower not and rest


I have the same model year as yours, but that does not really matter. If you go to the back of your Haynes manual, the wiring color codes are spelled out for you specific to your car, It is possible that a new or rebuilt starter can be stuck (clearan ... Morgan Aero 8

Hello, I replaced the starter selenoid on my 1990 F150, 6 cyl. truck because it would just buzz and not start. It ran for awhile. I went to start it and the rpm was very high. I kept tapping the accelorator and it calmed down a little, it ran about 100 yds. and just quit. Tried to start it again, but no power anywhere. I also noticed that there was a hot wire smell and the battery cable was very hot.


Here is a general instruction for changing the starter, you can modify it by just removing the selenoid after starter removal if you like.\015\012Disconnect the positive post of the battery cable. Underneath the passenger side of the truck you wil ... Ford F-150

1994 e-150 conversion with a battery guard system. not starting, no click at solenoid, just relay click. I replaced the starter relay due to the relay clicking but no starter rotation after. The ignition wire to the starter stays hot all the time (12 volts), but goes to 0 volts when the ignition turned to the start position. Any ideas???? I might have wired the relay incorrectly. I'd like to find a picture or description of the exact relay wire placement.


Bad ignition switch it sounds like. A contact may be bad inside your switch upon turning it to the start position ... Ford E-150

I have 93 Gmc Safari van I had the main Fuse link bypassed cause the wire was getting Hot and would have let van set for an hour then would start up again, so auto shop rewired it with - couple of enclosed fusible links well battery acid ate through them so I replaced 1 of them with a 30amp fuselink wire, BUT everyonce in awhile the 30amp blows after I turn my ignition off,. So when I have to start again I have to replace. That 1 fuse and then starts right up, Now what is causing it to blow fu


... Cars & Trucks

We purchased a 2006 equinox that was in a rollover accident to rebuild it. Someone I think removed a remote starter/car alarm. Can't seem to get the key to start the engine. We have taken a hot wire and started it by applying it to the starting wire to the selenoid switch, but the vehicle only runs for a couple seconds. I also think there was no power to the coil pack.(Had to supply power to that also.) Is there some kind of reset switch to push to restore the power from the ignition or fuel pum


Their is a safety cut out switch which looks like a inch square with a red or black rubber cover ,it should be under the bonnet but some older cars had one in the door pillar ,behind the footwell covers,in the boot ,when you find it just push in down ... 2006 Chevrolet Equinox

The ignition is broken and i need to hot wire it to get it to the garage the key was just turning in the barrel. then my girlfriend went out in it came back and coldnt turn the engine off so i took the casing off took the black cap off and turned it off with ascreew driver and started it again to see if it worked and it did but then i pushed the black cap back and i saw spark and then it wouldnt start.now my frriend told me i would need to hot wire it so i can get it to the garage.please help i


I think you better have it towed, it may be cheaper in the long run. I would disconnect the battery, you could end up with a fire on your hands if the wires short out. ... 1996 BMW 318

2004 jetta 1.8T . The wire that comes from the alternator to the fuse box on top of battery is getting so hot that it melted through the fuse box holder, the fuse did not break and the wire starts getting hot as soon as i turn on the engine. What could be the problem?


The could be your alternator, over charching, touching a ground, the wire needs to be replece if is melted. the auto parts can to test the alternator if you remove it from you car ... 2004 Volkswagen Jetta

1997 acura integra overheating when I get on it runs good when driving and shifting at 2Gs but if I shift at 3gs it jumps all the way to hot have changed the thermostat and bottom hose still cold while top is hot??? If I let sit goes back to good fans are running as soon as I start the car but I think po must have wired to come on. And does that ground wire have to be on the valve cover have replaced it but don't know what that does.just seen where other guy was having same proplem and replaced


If the the lower hose is cold and it runs hot then that tells me its not circulating.also there had to be a problem before if the fans are wired to come on when car is first started,may have a bad waterpump or exhaust is getting into cooling system, ... 1997 Acura Integra Type R

Have and saab 93 2000 turbo model sometimes when its hot or at the most unconvient time it wont start the previous onwer has and tap into the starter motor yellow wire that goes to the battey and if i touch the positive terminal once its starts do you have any idea and can i have the wiring diagram thanks robert


... 2000 Saab 9-3 Viggen

98 chevy k1500 my keys touched a hot wire inside the steering colum while starting, sparked and key got hot while pulling it out as fast as i could. Now blower ,radio,and wipers don't work. All fuses are good,not sure about the relays. I dont think one relay would go to those. Cheked wires that go into key cylinder, they appear ok but do you think if burnt on inside it would only effect those 3 items? This is a tough on for me to diagnose please help, thank you. Joel


... 1998 Chevrolet K1500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2422 seconds