Having problems with your 2002 Mazda Tribute ?

2002 mazda tribute blowing holes in egr valve

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2002 Mazda Tribute

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2002 mazda tribute blowing holes in egr valve


... 2002 Mazda Tribute

My 2002 3.0L V6 Mazda Tribute is blowing out the EGR Valve. I took it to dealer and said the pre-catalytic converter clogged up the main converter. They want 1900.00 to fix. Is there any cheaper solutions?


I have the exact same problem right now. It is possible that a misfire due to a faulty coil damaged the pre-cat and I found pieces of it clogged in the main converter. Unfortunately, to repair it right, I would suggest replacing all three converter ... 2002 Mazda Tribute

Could the catalytic converter cause the egr valve to blow in a 2002 mazda tribute


... 2002 Mazda Tribute

My mazda blew hole in egr valve and replaced egr valve and wont go over 35mph


... 2002 Mazda Tribute

Egr valve repair mazda tribute - 2004 Mazda Tribute


... 2004 Mazda Tribute

Engine malfunction Have a 2001 Mazda Tribute,3.0 engine.The check eng. lgt. came on and i took it to Auto Zone for diagnostic , it said EGR insufficient flow probable cause blocked egr passage,faulty egr valve,egr boost sensor malfunction.Any ideas wich one could be


Check for vacuum leaks on intake manifold,the air tube between the air filter.intake manifold vacuum hose.===clean throttle plate with Berryman carburator cleanerSEE sample picture ... 2002 Mazda Tribute

My egr valve burnt and has been replaced but my mazda tribute still wont start


... 2001 Mazda Tribute

2002 mazda tribuite misfire cylinder 5 & EGR valve issues


... 2002 Mazda Tribute

My mazda would not drive faster then 25miles ahour i opened the hood and found the egr had blowen a hole though the side of it and that dpe sensor had melted would replaceing fix this problem 2002 mazda tribute v6 3.0


... Mazda Tribute

I have a 2003 Mazda tribute lx 3.0 liter. Idle problem along with no power. Just doesn't have power to go like it use to. I changed EGR valve and idle control valve and still have problem. Anyon


... 2002 Mazda Tribute

2003 mazda tribute EGR valve


... Cars & Trucks

2001 mazda tribute replaced egr valve 3 times in 2 months


... Mazda Tribute

My 2002 mazda tribute has blown out two EGR valves and I don't know why. Please advise.


Catalytic converter may be restricted/collapsed. check for other exhaust restrictions. ... Mazda Tribute

Where can I find a diagram for 2001 Mazda Tribute Transmission Pan (Valve Body Cover)? It has 17 holes, and 4 different lengths of screws. They got mixed up & I need to know which goes where!


We need to know engine sizes there; try look in the follow link HERE.Hope this help ... 2001 Mazda Tribute

Replaced 2 egr valves in 2 days and both have had a hole blow through them!!!What could be the cause?


I had same problem. Catalytic Converters were clogged and pushing exhaust back through system. Blew hole in EGR Valve ... Mazda Tribute

Egr valve location - 2005 Mazda Tribute


... 2005 Mazda Tribute

I have a 2001 Mazda Tribute V-6 and I cannot keep it running at idle. I have replaced the EGR Valve and a fuel filter. It seems to be idling too slow. Any suggestions?


Go to my profile and see my tips for help with this. All you need to do is pull the idle control valve, clean it and lube it. It takes about 5-10 minutes, and your car will start and run great! ... 2001 Mazda Tribute

2004 Ford Escape XLT. Engine light on for two days - didn't drive. When leaving to take car to O'Reilly Auto to get a code read engine light no longer on. EGR valve blew a hole in the side if it en route. Purchased a new EGR valve and replaced. Car still not accelerating properly and blew a hole in new EGR valve within 20 minutes.


... 2004 Ford Escape

2002 egr valve problems


That would be exactly what I would look for... When the catalytic honeycombs become blocked, it causes a build-up of exhaust pressure... and this restriction in the exhaust will also have a very definite effect on engine performance: The typical ... 2002 Mazda Tribute

I am putting a Japenese pullout engine into a 1997 Celica, The *** engine is not drilled for an EGR valve. This is a 7AFE engine 1.8L. The company we bought it from says we need to drill a hole in the head for the EGR valve. I would like to know the best way to do this. For example is there a drill guide for this application. The hole on the old engine looks about four inches deep. We didn't want to start drilling without some advice.


I honestly have not read or seen an aftermarket drill guide for such a process. I would recommend taking the old cylinder head and the new cylinder head to an automotive machine shop that specializes in cylinder head refurbi ... 1997 Toyota Celica

Have 2005 ford freestyle. i towed to my shop, scanner showed 2 codes,bank1 lean, bank2 lean. told me to look for vaccuum leak. found dime size hole in upper intake plennum near intake opening. also egr valve over heated and housing seperated. suspect egr valve caused intake meltdown. installed new intake and egr valve,runs but no power,very quiet out exhaust,suspect restricted exhaust. tach does not go over 3000 rpm. exhaust temp very hot at tailpipe exit. have removed exhaust system all but 2 c


Measure the exhaust back pressure. Do you have an old O2 sensor? If so just break the ends off of it so that just the tube is left sticking thru the center. Install it in one of the O2 ports and hook a vacuum/pressure guage to it. Should read les tha ... 2005 Ford Freestyle

Po470 I been trying for at least 3 months to get rid of the PO470 code. I replace the egr boost sensor. But still no dice, the code still there. I think I may have a bad solenoid on top of the egr valve. I tested the egr valve by pushing the spring up, then putting my finger over the exhast hole on the valve. It held open. So I asume the solenioid is bad. So I tested it by using a 9volt battery to triger the plunger to react. Nothing . Help! on


... Ford F-150

Im getting water in the egr valve and egr soleniod. the egr has two vac ports one at the base of the egr blows air out but it is also blowing water.


... 1999 Dodge Grand Caravan

Failed EGR position sensor... Negative Back-pressure EGR valve: An exhaust-gas-recirculation valve having a normally closed bleed hole which opens when back pressure drops, reducing vacuum above the Diaphragm and cutting the recirculation flow. Where is this valve and how do I fix it?


... 2006 Chrysler Town & Country

I have a mazda Miata 1999. Check engine light came on and i got it checked and it has EGR Excessive Flow. The guy cleaned the EGR Valve today and told me to drive about 50 miles and see if it worked. Well, at 42 miles it came back on. I have always used 91 octane from Shell. Any suggestions? Other than replacing the EGR Valve?


I did a thorough cleaning of the IAC, EGR, intake etc, spend $ 100 in parts and the Check engine light still comes on - P402! I now take off the + terminal of the battery, let it sit for 3 min and reconnect. Voila the light is out! However it comes ... Mazda MX-5 Miata
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6601 seconds