Having problems with your 2002 Jeep Grand Cherokee ?

2002 Jeep cherokee check engine light on. code p0122 sensor reading 12.5% at idle. does anyone know what it should read at idle?

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Throttle/Pedal Position Sensor A Circuit Low Input
\015\012
\015\012This usually means the sensor is unplugged or you have an open circuit. Check the wires to make sure there are no breaks in them.
Repair Help & Product Troubleshooting for 2002 Jeep Grand Cherokee

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2002 Jeep cherokee check engine light on. code p0122 sensor reading 12.5% at idle. does anyone know what it should read at idle?


Throttle/Pedal Position Sensor A Circuit Low Input\015\012\015\012This usually means the sensor is unplugged or you have an open circuit. Check the wires to make sure there are no breaks in them. ... 2002 Jeep Grand Cherokee

My son has a 2001 elantra, we had it read on a code machine so many codes came up, they didn't know what to check. The car will start and idle for 2- 3 minutes that it just stops. We changes the oxygen sensor,idle air control valve, the maf sensor and the throttle pos. sensor. We checked the pressure on the fuel pump and that is good to. my question is where do I go from here.


Check your egr valve it may be sticking or clogged by carbon can remove and clean with a carb cleaner aslo check operation of valve that it moves and not stuck with the cat converter start vehicle and put hand by exhaust give a little gas if it feel ... 2001 Hyundai Elantra

1998 Jeep Grand Cherokee Laredo 4.0 6cyl, when i crank my jeep after about 1 or 2 min it will start idling very rough and the exhaust smells very rich. Seems like the motor is starving for air but there's no vacuum leaks. I have already replaced the idle air control sensor, fuel pump, fuel regulator, plugs, plug wires and air filter. Its not throwing any codes and even though the check engine light doesn't come on Ive still check it numerous times. Has anyone else experienced this or know wh


Have you checked the coolant temp sensor. They also have something called a MAP(manifold absolute pressure) sensor that could be causing this issue. This sensor will have a 4 pin connector and 1 vacuum line going to it. Should be on the firewall, jus ... 1998 Jeep Grand Cherokee

My 2002 ranger xlt starts to rock when at idle. Just replaced maf sensor and idle sensor motor, don't know what else to do. Check engine light is on and test reads bank system 1 and2 too lean..... Parts store said exhaust leak, I'm not so sure


Check for vacum leaks on the intake manafold some of the plasitic manafolds warp n dont seal on the gaskets ... 2002 Ford Ranger Regular Cab

New engine I have just put a a 350 in my 1991 chevy caprice, replacing my old 305 but I am have a problem. With the temp sensor connected the car idles down and then it catches it self and when I put in gear it stalls out put cranks right back up. It will run like a dream on the highway when a have the temp sensor disconnect but the check engine light will say on. I know that with the temp sensor pluged it is retarding the PCM. I guess my question is how can I reset the PCM to read this new engi


The problem is the temp sensor itself. <try using the old unit that must be fix to the old motor. Or buy a new one BUT solicityng it to your old motor model. There are several sensors with identical fisic aspect and different electrical tolerance. ... 1991 Chevrolet Caprice

Crankshaft Sensor Hi Everyone, My car has never given me problems, but now the check engine light is on. My fiance hooked up his scanner (he is an a.tech at a subaru dlrship) to my car, and it read 'crankshaft sensor'. He erased the code, but it came right back after one day of driving around. Obviously, the crankshaft sensor is bad. Heres the question, does anyone know how easily it can be replaced? He is a mechanic, so i would much rather have him do it for me to save on costs. However, he is


Simplely locate the the bottom belt pully (hormonic balancer) and will be right behind it at a 5 o-clock position one screw and clamp changes it ... 2004 Nissan Sentra

CTS Check Does anyone know how to check the coolant temperature sensor in a 1999 Ford Taurus? I want to check mine to make sure it's working because I don't trust it much right now. I have a multimeter to be able to take the readings.


Yes it is an easy check first test the switch cold the resistance should be high and then put the switch in hot water close to boiling point and take another reading the Resistance should be low if not then the gage ... 1999 Ford Taurus

I have a 1999 ford escort 2.0 DOHC and it will crank but wont start...it had a new fuel pump put in it and ive put a cam position sensor on it and a battery..its gettin fire and its blue spark but still no start..checked compression and all cylinders read 80 to 90 psi..idk what the compression is supposed to be but it seemed low... If anyone knows somthing that i dont please let me know..email me at [email protected]


... Cars & Trucks

My 2003 chevy trailblazer ls rpm gage has completly stopped working. when it first started going bad it would work on occasion and now the needle doesnt even move from 0. my car feels and sounds like it is shifting when it should its just the gage that doesnt work. what could cause this? is it a bad sensor, wires or something all my other gages work fine its just the rpm gage. if anyone knows how i can fix this problem please let me know what i need to check i want to be able to fix it myself if


... 1996 Audi A4

1996 isuzu rodeo keeps reading #2 misfire runs good xcept when cold it hesitates most times or jus occasionally hesitates then the check engine light flashes and its guzzling gas i only got 50 miles on a half tank of gs( i know WOW) ive replaced mass airflow throttle position sensor egr valve new plugs and coil packs filter o2 senors idle position sensor fuel injectors cleaned alot of carbin out of throttle body HELP


A misfire alarm typically means the coil pack mounted above the sparkplug indicated in the misfire had gone defective. \012\012To test it, swap the coil pack with another cylinder, and see if the misfire goes from #2 to the cylinder you p ... 1996 Isuzu Rodeo

Cooling Fans I changed the sensor thinking that it would make my cooling fans work I also checked the relay and my cooling fans still does not work when my Aztek idles for just a few minutes the temp will start rising. I went to AutoZone to get a repair manual, but they do not carry them and can not get one does anyone know where I can find an online repair manual so I can see the wiring diagram or does anyone else have this problem?


Hello dc8jimmy...did you check the voltage to the fans? The Aztek is a known overheater...Run a diagnostic scan to see if you have a cooling fan relay circuit open short. Will be easier to correct the problem when you know where to look. I think Hay ... 2001 Pontiac Aztek

Hi, I have a 2002 dodge grand caravan sport and my check engine came. I hook it up to the scanner and it gave me an o2 sensor read out. Now my question is those anyone knows or know if there's 2 becau


Do you have the actual code ? ... Cars & Trucks

97 Grand Prix 3.8 SC I replaced left rear abs sensor. the Ohm reading was 2M ohms. The good one read 1100 ohms. Still not good. I know how to check the wire harness that go from the sensor to the frame. How can I check the wires from there to the BCM. I do not know where it is, other than near the steering wheel. Also not sure of the wire colors.


Double check that harness on trail arm wiggle harness when checking also pull on wires from back side of connectors they brake a lot also check for loose terminal tension in connector also big problem on this car ... 1997 Pontiac Grand Prix

Poor acceleration, check engine light on fo rmonths, low idling I have I am not sure what to do. Keeps reading code for plugs and wires, but they have been changed many times. Along with the cap and rotor, and ignition coil. I don't want to junk it, but it wont pass inspection. Even the dealerships having problems finding the problems. Anyone know?


Have your catalytic convertor checked ... 2000 Dodge Caravan

My Honda Civic 1.4i S 1999, failed its MOT. Due to lambda reading on 2nd fast idle. Does anyone know what this problem could be? and where in the car the lambda sensor is?


It's also called your O2 Sensor and will be located in your exhaust manifold ... 1999 Honda Civic

Car overheats I have a 1995 Grand Am SE that whenever I idle in traffic it tends to overheat. I've replaced the thermostat. My friend and I noticed that the rad fan would not turn on, ever? I took the rad fan out and tested the power source to the rad fan motor (now I have never used a voltmeter before, have a decent idea of how it works, but got zero readings no matter what I did) I don't know exactly where the sensor is or how to get at it and change it? How to I check a fuseible link? I'm so


Hey Alex ! Try this. Make sure the fan does not turn on for any reason.\015\012-Lift hood\015\012-Start car\015\012-let engine get hot\015\012-observe as engine gets hot just sitting there idleing if at any time the fan swit ... 1995 Pontiac Grand Am

I have an OBDCOM diagnostic code reader. I am using it on a 1999 Chevrolet Tahoe. It tells me what the O2 sensors and everything are reading, but I need to know what the fuel trim, the O2 sensors, and everything else is supposed to read. it is no good to look at these readings if you don't know what to look for. can anyone help?


Hello! With your purchase of OBDCOM you have free technical support 24/7...Any questions that you have are answered...It is a complex system; Give them the readings and they will interpret the data for you...Guru.......Saailer ... Chevrolet Tahoe

I have an OBDCOM diagnostic code reader. I am using it on a 1999 Chevrolet Tahoe. It tells me what the O2 sensors and everything are reading, but I need to know what the fuel trim, the O2 sensors, and everything else is supposed to read. it is no good to look at these readings if you don't know what to look for. can anyone help?


Fuel trim means the amount in % that the fuel control system is compensating for a rich or lean condtion engine condition, so what this means is that any fuel trim negative or positive in excess of about 10% is a sign the system is biased lean or ric ... Chevrolet Tahoe

My 1992 ford f-250 used to get 17 miles to the gallon, now it idles high and I get horrible gas mileage. I ran the codes but it tells me the system is fine. I have metered TPI sensor and it reads good. I also put a brand new O2 sensor in it, that did not help. I dont know where to look now since the trucks diagnostic reading came back good 111 on both KOEO and KOER. Every once in a while the truck drops to correct idle but raises back up within seconds. Can anybody point me in the right directio


Check the Engine Coolant Temp sensor. if there is excessive resistance the the ECM thinks the engine is cold ... Ford F-250

Need help AGAIN! with the sonata ok so we changed the map sensor now it stays at a good idle but when i give it gas the intake sounds loud and the car turns of so this is what i checked so far 1- Fuel pump 2- Injectors 3- Fuel Rail 4- Comppresion 5- Head Gasket 6- Crankshaft posion sensor 7- Intake Manifold 8- ALL Vac lines 9- Checked for bent valves 10- Maf sensor 11- Camshafts They All Checked Out Ok Anyone Else Wanna Give Me Some Advise?


Does it shake then turns off? check your sparkplug wires, they may be arcing. Is the timing correct? check that as well. ... Hyundai Motor 2004 Sonata

2004 Volvo S40 2.4I engine check light is on, light is cleared and returns a week later, engine drives normal with light on. codes read P0172 system too rich bank one, P0191 fuel rail pressure sensor circuit range/performance, P1090 fuel rail pressure sensor circuit. now i need to know how to test to see if its the sensor that is faulty or the wiring circuit, replacement of the sensor is over $1000 and cant be returned so need to know im making the right choice by changing the sensor. thanks


... 2005 Volvo S40

I have a 2003 GMC Envoy and the check engine light comes on peridically. Auto Zone checked it and Code 0128 was the alleged issue. However, where is the sensor? No one seems to know the location of the oxyven sensor even Auto Zone sold me a part that does not exist in the location they provided from their printout. Can anyone help with location of the sensor?


This code relates to low coolant temperature not the 02 sensors. You should change your thermostat, it's stuck open and is not allowing the engine to properly heat up.\015\012\015\012By the way, there are 2 92 sensors on Envoys and Trail ... 2002 GMC Envoy XL

I HAVE A 2003 SATURN ION. THE CHECK ENGINE LIGHT KEEPS COMING ON. I HAD THE CAR HOOKED UP TO AN ANALYZER AND IT COMES UP WITH A MAP SENSOR CODE. I REPLACED THE MAP SENSOR AND THE PROBLEM DID NOT GO AWAY. THE CAR, AFTER DRIVEN FOR ABOUT 15 MILES ON THE X-WAY, IDLES AT 1800 RPMS UNTIL I TURN THE CAR OFF. WHEN I START THE CAR, WITHIN A FEW SECONDS, IT IDLES FINE. I TOOK IT TO A GARAGE AND WITH THEIR ANALYZER THEY COULD FIND NOTHING WRONG OTHER THAN IT LOOKED LIKE THE COOLANT TEMP SENSOR WAS READING


On your vehicle when the Check engine light comes on and a code is store, the driver can retrieve the codes themselves with the onboard diagnostics. Put the key in the on position and watch for the light.The light will blink in a code .FOR EXAMPLE: ... 2003 Saturn ION

I dont suppose anyone on here knows what voltage the throttle position sensor should test out at do ya? I know that I need to unplug the plug from the TPS, and use a voltmeter with the key turned forward. I just am not sure what the voltage should be at idle, and at load acceleration. PLEASE HELP!! If anyone knows!!


1.5 volts to .8 for yours\015\012\015\012please check out this website for a vidio with a example of testing different tps sensors\015\012\015\012\015\012 ... 1986 Ford Ranger 2WD

MAP sensor reading at idle 1994 Pontiac Firebird with a 3.4 V6, 5 speed manual and air conditioning A/C (just passed 150K miles). I'm not getting a check engine light but it will suddenly runs rou


... 1994 Pontiac Firebird
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3365 seconds