Having problems with your 2002 Ford E350 ?

Location of the crank positioning sensor on a Ford 1999 e350 v10 std emissions?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

The CPS is located in the engine block right next to the A/C compressor. You'll have to unbolt the compressor to have room to remove the CPS. Don't remove the A/C lines, just unbolt the compressor so that you can move it out of the way. There is one bolt holding the sensor in place and you can just pull it out after you remove that bolt.
Repair Help & Product Troubleshooting for 2002 Ford E350

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Location of the crank positioning sensor on a Ford 1999 e350 v10 std emissions?


The CPS is located in the engine block right next to the A/C compressor. You'll have to unbolt the compressor to have room to remove the CPS. Don't remove the A/C lines, just unbolt the compressor so that you can move it out of the way. There is o ... 2002 Ford E350

Locating crank position sensor on ford expidition 5.4 motor


... 1997 Ford Expedition

Location of crank shaft position sensor on ford f250


... Cars & Trucks

Wont start i have a 96 ford explorer v6 engine. It wont start in various locations after running fine to the location. I have replaced the fuel filter, fuel pump, fuel pump relay, coil pack, control module, ignition switch, and crank position sensor. I have run out of parts to replace. It seems like every time i fill up the gas tank it gives me trouble. If it sits for a long time it seems to help. Sometimes it dosent matter how long it sits. I tested the spark plugs and it dosent seem to spark w


I would check the cam position sensor ( at the right rear of the engine) and the plug connector at the PCM. I believe when you say "control module" you mean the PCM because these engines did not use a separate ignition module in '96- it is all done b ... 1996 Ford Explorer

Location of crank position sensor - 1990 Ford Festiva


... 1990 Ford Festiva

Im trying to find the location of the crank shaft position sensor for a 2002 ford taurus. Im wanting to replace it myslef.


Hi you will find the crank shaft sensor on the passenger side of the engine on the back side right behind the harmonic balancer. \015\012If you remove the front tire and the plastic splash shield you will be able to locate ... 2002 Ford Taurus

Where is the crank position sensor located in an 85 ford f250 5.8L?


... 1985 Ford F 250

Where is the crank position sensor located on the 2002 Ford Escape? Will I need a rubber O ring or paper spacer?


The Crankshaft Position Sensor (CKP):\012\0124 CYL - located on the front of the engine, near the flywheel end of the block. remove exhaust manifold, disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket r ... 2002 Ford Escape

2008 ford fiesta crank shaft position sensor location


... Cars & Trucks

Location of crank position sensor on 1990 ford festiva


... 1993 Ford Festiva

Location of crank position sensor 2002 ford taurus 24v engine


... 2002 Ford Taurus

LOCATION OF CRANK SHAFT POSITION SENSOR FOR A FORD VAN E250 2003


... Ford Econoline

Location of cam and crank position sensors - 2001 Ford Escort ZX2


The cam sensor is located at the front right front side of the cylinter head, while you are facing the engine.---------- \015\012The crank position sensor located below the pcv valve that is located on blo ... 2001 Ford Escort ZX2

Where is the crank shaft position sensor located on the 2006 ford F 350 super duty pickup truck .


Should be on front of block like behind harm balancer has wires going to it and a plug on it ... 2005 Ford F-350 SD

Crank position sensor, where is the crank position sensor located, and how is it reached?


Kia 2002 v6 2.7 no spark on no.1 and no4  have spark on 2&5 -3&6 have changed cam sensor no help  hope u can help tks jt ... 2002 Kia Optima

Where is the crank position sensor located on 93 jeep grand cherokee..all the post ive seen are for the 4.0..what is the way to accesss the crank position sensor. from the top or the engine or the bottom?


Normally , they are close to the harmonic balancer area, you should be able to get to it better from the bottom, put the jeep up on ramps or safely on jack stands. ... Jeep Grand Cherokee

I have a 1998 Ford Explorer V6 4.0L I am trying to find out were my Camshaft Position Sensor is located and can i get to it without having to remove any other parts such as air intake lines or anything like that if you could hook me up with a diagram or picture of were the Camshaft Position Sensor is located it would be much appreciated, even if you cant get a picture or diagram if you could explain were to find it that would be great. Thanks, Billy Blackwelder


It should be on the drivers side valve cover directly to the rear of the the oil fill cap, should have one bolt that holds it in place with two wire connector on it. ... 1998 Ford Explorer

Where is the crank shaft positioning sensor located on a 01' Cherekee Sport with a 4 liter? What are the symptoms of a faulty Crank shaft positioning sensor?


Look at the area around the crankshaft pulley. It's bolted to the block and senses the crank position. If it fails, You won't have an ignition spark. Good Luck, Ned ... Jeep Cherokee

Whare is the Cam position sensor located? 1998 Buick Lesaber with 3.8L Issue is Car will turnover but not crank on hot days only. In the morning the car will start every time but later during the day it wont start. I have replaced the fuel filter, battery, battery bolts, coils, mounting plate coils mount onto, and a MAP sensor on top of the motor. I am running out of ideas. I am going to clean the mass air flow sensor and plan to replace the cam position sensor, but after that I don't know.


Car starts up stays on for 2 min cuts off & doesn't start back up\015\015 ... 1998 Buick LeSabre

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


Cam sensor bottom of engine p.s. before you replace part ford has a recall on the cam sensor and might replace free of charge ... 2005 Ford Excursion

I have a 97 ford taurus and I have replaced every possible sensor that you can think of as well as the alternator and the cam position sensor and the snythanizor,crank sensor, fuel pump and filter, catylist convertor and this car for some odd reason is still hard to crank.


'hard to crank', meaning it is hard to start, or it cranks slowly? If it cranks slowly, your starter is probably going south-if you mean it is still hard to get it started, it sounds like you did all the repairs on the ignition side but have not add ... 1997 Ford Taurus

2003 Ford Van E350 crank sensor problem - 2002 Ford E350


... 2002 Ford E350

Where is the cam shaft position sensor located on a 2001 gmc 5.7 , and also the crank position sensor?


If this is a 5.7L the cam sensor is in the distributer and the crank sensor is in the timing cover ... 1995 GMC Jimmy

2001 Hyundai accent crank position sensor needs replacing. Diagnostics test. The car would stall and then start again about 20 mins later. Can anyone tell me where the sensor is located with some detail??? send picture of location if possible.Thanks


Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about y ... 2000 Hyundai Accent
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.1263 seconds