Having problems with your 2002 Ford E250 ?

How do you replace brake pads on a 2002 e250 ford van has shoes and pads

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2002 Ford E250

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you replace brake pads on a 2002 e250 ford van has shoes and pads


... 2002 Ford E250

Replace front brake pad ford econoline e250 van 2003


... 2003 Ford E250

Brake question Does the 2003 Ford Taurus have rear brake pads or shoes?Also, if they have gone to the point that the brake pedal has to be pushed all the way to the floor and the rear brakes are screeching does that mean that the drums will have to be replaced as well as the pads or shoes?


Give these websites a try www.alldatadiy.com and www.autozone.com and ... 2003 Ford Taurus

Brakes brake doesn't stop,when i facing a enmergency stop??? I had drove the Ford Freestar mini van for a years,it's brake never make me feel good.so I had the brake pad replaced month ago (AP..).after that, i feel the brake is more soft,then i found it is hard to stop when i have stop it suddenly ,even doesn't feel it is stopping.I took it back,they said no thing wrong,now i don't feel save to drive it,can't follow the other car as close as it suppose to be! anyone knows Freestar mini van's bra


Sounds like your abs feature is in-operative(that's the one that won't allow the wheels to lock-up when the brake is applied in an emergency)the abs system should pulse your brakes during an emergency application of pressure on the pedal,i'd get to a ... 2006 Ford Freestar

95 ford f-250 73 disel i replaced the front pads and rotors, compressed the pistons on the calipers with out opening the bleeder and i also replaced the rear brake shoes and resurfaced the drums and bled the air out of the system all the way around, but now the the brake pedal feels spongy, the master cylinder is not leaking, what you guys think i should do or replace next, please help.


Inspect first the repairs that had been done first before proceeding to the next step. Check if the bleeding procedure has been done properly. Spongy breaks is normally caused by air in the hydraulic system. Below is a link to describe the correct ... 1996 Chrysler Cirrus

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before installation and bled all wheel cylinders as well; have also replaced rear anti-lock system; the rear anti-lock system light on the dash remains on; the pedal gets hard when bleeding the brakes, however, does not stay hard after bleeding. Does the anti-lock system need to be bled as well? If so, how?


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them. ... 2007 Ford E-350 Super Duty Length XLT

My Ford E-350 Van Shakes when braking. I have replaced the Rotors and Brake pads and it still shakes only when braking. What else could be causing this?


Welcome to the world of Ford Truck!!! The rear rotors come off the same way that the front rotors come off, only they get REALLY stuck to the rear hub assembly. Once you have removed the caliper and caliper mounting frame, take a ... 2002 Ford E350

I have a 1996 Chrysler Town & Country. The front brake pads were replaced about 3 months ago, the rear pads were replaced about three weeks ago. The brake lines or cylinders were not touched. I experienced a total loss of braking about two weeks after the rears were replaced. Took the van to Big O. They replaced the rear cylinders and completely flushed the brake fluid. The van now has a hard pedal the first time you press it, then goes to the floor if you release the brake and press it agai


All this is because the brake lines have not been 'bled' properly. That's why when you pump the brakes, it changes how they feel. Air in the line does that. Have them bled again. ... Chrysler Town & Country

I am trying to replace the rear brake pads on a vauxhall combo van, Y reg, I am having difficulty removing the brake drums, when I have done this before, there has been a adjustment screw which when undone allowed the removal,there is not one and the drum is catching on the brake shoe, is there any way of releasing the drum.


There should be two small threaded holes, insert the proper size bolt inside and screw the bolts in, alternating a few turns at a time. This will force the drum off the brake shoes. ... 2000 GMC Envoy

Need to replace brake line on a E250 ford van from the front to back wheel housing, does anybody have a diagram or what replacement line That i could use? It looks as through there are 3 different sections and the first 2 from the front look bad ,right were they couple together and run in thru the frame. are there more sections or just these 3?


I'm not totally sure but if you looked at it and see 3 sections that's probably how many there are. The brake lines are usually not hidden away and are usually always on the outside of the vehicle ( for obvious reasons). Go for it, you can handle it, ... 2001 Ford Econoline

How do I change the brake pads on my Ford E250 van? I have it apart but can't see how to remove the pads. They seem to be "trapped" in position.


Pry them away from the rotors and be sure to install new rattle clips with the new pads. ... Ford E-250

Front brake pad diy replacement Ford E350 van 2004


There are Clips on the Back of the Pads that sit on the Piston side of the Caliper. Take a ScrewDriver and Pry them off. It will be Fine. Please Rate My Response! Thanks! ... 2004 Ford Econoline

Ford f-250 95 7.3 turbo dsl abs we replaced the rotor,pads,shoes,calipers, drums,master cylinder ,but still has the same problem, what it does is that everytime you start the truck you step on the brake pedal and it goes down slowly it goes down almost to the floor, i'd like to know what it is and how can i check it and fix it,thank you.


Check the fluid in the master cylinder and see if it is low.If it is,pull the rear wheels and and adjust the rear drums so that you can still turn the drums,but the drums are a little bit hard to turn.See if this fixes the problem.If it does not,Then ... 1996 Chrysler Cirrus

HOW DO I REPLACE A BRAKE MASTER CYLINDER ON A 2003 FORD E250 VAN


... 2003 Ford E250

I have a 2007 Ford E250 van and have no running lights in the rear. I have brake lights and reverse lights just no running lights when headlights are on. Replaced headlight switch already and all bulbs in rear.


Locate the ground wires for each side of the lights in particular the running lights. it's usually just attached to the frame by a screw. undo the screw and clean the area and put the ground wire back on. also do you have a multimeter or test ligh ... 2007 Ford Econoline

Hi guys, I have a 92 Ford e-350 super wagon with the 7.3 diesel. Sometimes my brakes are hard as a rock and I cant stop the van! I already have new pads, calipers, drums and shoes, but something is making the pedal very hard and not work. Any ideas? Thanks!!


It is your brakes lines. most likely you have some blockage in the lines something isn;t allowing you to activate stopping power of calipers around the rotors. check for air in your brake lines and then check your master cylinder. ... Ford E-350

I have a 2000 ford taurus DOHC engine, auto trans. Have a sound from the left rear that is just like metal to metal brake - however it has made this sound before and after shoe and pad replacement. Could it be that there is a bad wheel bearing back there or should I be looking at something else?


It could b a wheel bearing or the drums or rotors may be bad and damaged your brakes hope this helps ... 2000 Ford Focus

1982 ford club wagon 1 ton van replacing brake pads .how do I remove the calipers?


The calipers are held on with wedges , tap them out with a hammer, use new wedges and silicon lube for reassembly, ... 1983 Ford Club

Brakes 1997 Ford Explorer. Just had new rotors and pads. When braking, especially at low speeds, there is a grinding noise, and it then appears that the brakes stick. Returned it to mechanic who checked out everything without detecting a problem. Was told that the ABS system would have to "re-learn" the braking pattern, and the problem would go away. It hasn't, and brakes seem to be dragging. I just replaced the rotors, pads, and bearings on my 1999 ford explorer Sport.  It was a relatively eas


This seems like two different vehicles with two different problems. first the 1997 Ford Explorer- with new rotors and pad. I can almost guaranty that the rotor and pads that were replace are "after market" parts. If it is tr ... 1999 Ford Explorer

Brakes 1997 Ford Explorer. Just had new rotors and pads. When braking, especially at low speeds, there is a grinding noise, and it then appears that the brakes stick. Returned it to mechanic who checked out everything without detecting a problem. Was told that the ABS system would have to "re-learn" the braking pattern, and the problem would go away. It hasn't, and brakes seem to be dragging. I just replaced the rotors, pads, and bearings on my 1999 ford explorer Sport.  It was a relatively eas


You may have to take the rotors back off completely and look for the baby brake shoes behind the rotors because sometimes they will hang up and give you some of the problems you are having ... 2001 Ford Explorer Sport

I have a 1998 dodge van b1500 van 5.2l. I recently replaced the front brakes. I have heard a small knocking noise since the replacement. It is most noticeable at 30mph. When i step on brake it fads out only to return. I took the wheel off and inspected the brake slide and gave them a little ubing thinking that the pads were sticking. It seems this wasn,t the solution. Any thoughts on this? many thanks in advance


Hi\015\012\015\012Guess it’s the pad moving in the caliper.A set of anti-squeal shims should sort it....pugs also use a strange wire setup to hold the pads...have a look if you have alloys on, this might have been put on incorrectly ... Dodge Ram 1500

I am replaceing rear disc brake pads on a 2007 ford exp do i have to or sould replace the brakes in side the rotor? they look like only enmer, brake pads?


If there not worn just adjust them, if worn replace them you will the parking brake for inspection. ... 2007 Ford Expedition EL XLT

Brake pedal needs to be depressed very hard to stop,pedal is mushy,pads and shoes have been replaced, rear wheel cylinders have been replaced.calipers have been replaced, front brake lines have been replaced,master cylinder has been replaced,brakes have been bled till they run totally clear. seems like front brakes will lock up on snow and ice and skid this is a 1996 suburban k1500 with 112,000 miles,I'm completely stumped what am i missing?


The pedal goes down a long way(Rear brake shoes out of adjustment) or the pedal is hard to push and you have to about use two feet to stop the truck? (booster problem) ... 1996 Chevrolet Suburban

Hi i have a 1995 cheverolet silverado 1500. For years i've had the problem of a really soft brake pedal that goes all the way to the floor before it brakes. It has abs, front disc brake and rear drum brakes. I have recently replaced the front brake discs and pads and rear brake shoes and drums. We then went on to replace the brake master cylinder and the brake booster but it still has the same problem even with numerous number of attempts to bleed the brake lines. There is no air in the system t


If you haven't already, check your rubber lines for weakness; they could be ballooning under pressure. ... 1995 Chevrolet K1500

Brake problem Took 1996 Ford Winstar to get brakes checked at Ford. They relined all brakes, turned rotors, and replaced pads. When I drove it I could hear a chirping sound when tire rotates, when brake is applied the sound goes away. Took it back to Ford 3 times, they said they couldn't find the problem, (even though they did it). Any suggestions?


It sounds like your disk brakes are the problem. two ways to fix the problem. champfer your brake pads or basically glue your pad to the caliper piston with some stuff called disk brake quiet. the shop probably does not want to take your whole front ... 1996 Ford Windstar
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.7728 seconds