Having problems with your 2002 Chevrolet Tracker ?

Just pd 404.00to have front brakes roters Is that too much?Thank you.

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Yes, You should have paid about $50 each for new rotors , max, and about $100 for a complete brake job. Unless you have 4 wheel drive or something exotic, and your truck is fairly new, you could of had the rotors turned, for about $10 each if they needed it. ,,,,My wife went to a shop once for something and they told her that her brake pads were worn down to 3mm, and of course, most people will think, 3mm!!! Oh my, get them fixed, but she came home and told me what happened, and I said, 3mm, let's see, .120" , that is about half worn of a .250" brake pad, plenty of miles left there, they just wanted money, they make a lot of money on brake jobs.
Repair Help & Product Troubleshooting for 2002 Chevrolet Tracker

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1999 durango the abs light and brake light comes on about 3 or 4 times in the past week as im driveing and then goes off in a few minutes i have new brakes and roters on the front and only rear wheel abs, my brakes feel just fine , i have checked the wires at the cab and speed sensors and brake lights

Did you check the speed sensor on the rear end on top of the rear end. this sensor works the speedometer the abs and break lights and power door locks ... 1999 Dodge Durango

We recently replaced the front brake pads and turned the roters on our 2004 PT Cruiser. However, when applying the brakes on a hard quick stop, it makes a god-awful griding noise. Doesn't do it with a "soft" stop or soft braking, only on hard brakes. Was really bad after a hard rain and we had to make a quick stop. Also, we're hearing a slight high-pitched scraping noise when you start out from a dead stop. It goes away after you reach a higher speed.

Brake repair is pretty simple as long as you know what you are doing. That's the reason why mechanics who do know have a brake adjusters license as extra security for the consumer. If someone repaired your brake system and unlicensed would be unhelpf ... 2004 Chrysler PT Cruiser

I installed new roters and calipers on the front of my 1998 explorer and new brakes on the rear.now the brake pedal goes all the way to the floor even after we bled the brakes

Dealership has to use scanner and pressure bleeder to bleed brake system. ... 1998 Ford Explorer

2004 nissan maxima makes cracking and pulsating sounds when driving over 45mph. I have changed both front roters, front right axel, replaced wheel barrins, both front calipers, new rear brake pads, replaced all four tires and it stills makes cracking and pulsation noice and affects.

... Nissan Cars & Trucks

I just replaced the front brake pads on our 2006 Scion. I did NOT remove the whole assembly as the roters did not need replacing or turning. I removed the center roter assembly, but not the frame around it. I did NOT take off the hydrolic lines or open the bleed nut. It is the easiest and most straight-forward pad replacement I've ever done. Unfortunately, when I finished and went to test drive it, the Scion wouldn't move. It acts like the wheels are locked from turning. I can start it, t

You probably pushed in the piston with the cap on the reservior. That or there is too much pressure between the abs motor and the caliper. Loosen the bleeder at the caliper and see if it pushes out fluid. If it starts to squirt out, close it as soon ... 2006 Scion xB

1999 cadilac deville. when you driver over speed bumps,you hear a sqeeking noice as the car bounces. noice comes front front end. #2. air blower works but does not turn off. Madr a switch to turn off and on. Last when pressin the brake peddle, the entire steering wheel and car vibrates bad. roters are 2 months old

#1 The squeeking is likely due to worn struts. Replace the struts. You will also get a better response over bumps. #3 Rotors are warped. If inferior quality parts were used, it will occur again. Turn all the rotors again. On the car will work better. ... 1999 Cadillac DeVille

My clean 1994 le baron 3.0 gets a strong vibration when i am excelerating, it is most noticeable around 28 - 30 mph, i dont really feel it in the wheel but it is a strong shake. any ideas ? the front hubs feek tight with no play, the rear inner and outer bearings were just replaced the car is in excellent shape, however could use the roters turned next brake change(starting to feel a pulse when on the brakes)

... 1994 Chrysler LeBaron

1994 F-250 7.3 Diesel, and the ABS light is on the dash. If I have the codes clear the light goes out intil i move just a few feet and comes back on. It has a rear end housing sensor and i change that and had the codes cleared, and still the same. Front wheels are roters and rear wheels drums brakes. At this time i do not think there is any front wheel sensors. Do i check the module for a open circet with a meter? Do i change the module at this time? Can this cause my cruse control from working

You need to find out what the codes are before you replace anything more. If you have the RABS system, you only have the one sensor that you replaced. I've replaced more actuators than modules. Your workshop manual should tell you how to obtain the c ... Ford F-250

Are my front brakes pads(disc) supposed to be flush and touching with the roters when the emergency brake is Not on?

Yes. The emergency break only works the rear brakes. The front pads should touch but not bind. Can you turn the rotor with the brakes not applyed? If so, you should be just fine. ... 1994 Plymouth Voyager

1995 saturn sl2 changed out and bench bled master cylinder, bled all lines and checked front roters and rear drums, This car does not have ABS brakes,car will not lock up when brake pedal is aplied all the way?

... Cars & Trucks

I have a 1998 mazda 626. I just had the brakes and roters replaced on the front end and now my cruise control will not even turn on. Is this problems related to the brakes or do you think it is something else?

It sonnds like when thet worked on the brakes egither donn;t reconnect or damaged the vehicle wheel speed sensor there is one on each wheel and would affect the cruise control opperation ... 1998 Mazda 626

I have a 1996 ford escort lx and 2 months ago I replaced the front brake pads I'm now having to replace them again do because the passagener side is alread worn down to the ribits driver side looks new still and I even changed the roters

Hi this sounds like you may have a seized caliper on the drivers side, what is happening is all the pressure is going onto the passenger side and is doing the job of 2 brakes, may be more if it has worn that quick, you will ... Cars & Trucks

How do i no if my front end on my 1996 jeep cherokee is bad? when i put on the brakes it shimmys, i change the roters , & clipers & pads . nothing work

The rotors, caliper, pads are brakes, and won't cause shimmy, even if the rotors are running out, you will only feel it in the brake pedal.Shimmy is usually bad tie rods or wheel bearings, bad hub. If you changed the rotors, then you already ... Cars & Trucks

Okay so i know i posted this problem mulitply times But ive been narrowing things down. I noicted my car only makes a rattleing noise when its cold like the more you drive the louder it will get. And i was laying on the hood while my friend was driving the car and i heard the noise coming from the front passenger side could it be the brakes and roters they are in bad shape?

GM products use little tab that as the brake linings wear down, the tab makes contact with the rotor to warn you of inedible failure. This would present more as a squeek rather than a rattle. Raise the vehicle and remove the wheels so you can inspect ... Buick Rendezvous

Front brake roter how to get it off 3/4 ton - 1999 Chevrolet Suburban

I had to do this on my K2500 4X4 not too long ago. It was a bit of a pain. You will need to rent a special puller. They can be found at most part places. The hub and rotor come off as a single unit. Once you pull the hub, the rotor is bolted to the h ... 1999 Chevrolet Suburban


The calipers could both be frozen up on them ... 1997 Pontiac Grand Am

Car lot service dept. wants $260.00 parts and labor for front brake pads and roters. too much?

Way too much. go to midas or a small shop. rotors for your car should cost 30-35 dollars a peice, you can lifetime pads from advance for about 21.00 dollars.=$91.00 total on parts. 170.00 labor? way too much. ... 2005 Pontiac Grand Am

Front end shakes at hire speeds and when brakes are pressed already had roters turned

I have had this same issue what was your fix? I investigated to find the person who had the van did not use any brake lubricant so the pads were not deploying correctly. Will test drive tomorrow on longer trip. ... 2005 Chrysler Town & Country

What are the bearings that are on the front left cv axle that hooks on to the back of the brake roter

A wheel bearing ? ... 1992 Chevrolet C1500

Loud grinding in front driverside brake when applied, the pads are only half worn and I can't feel any significant grooves in the roter

This happened with our police interceptors on Hope Princeton Highway and the mechanic always found that a small gravel stone had lodged in and around the brake pads causing rough noise to come and go. ... 2003 Pontiac Montana

Just pd 404.00to have front brakes roters Is that too much?Thank you.

Yes, You should have paid about $50 each for new rotors , max, and about $100 for a complete brake job. Unless you have 4 wheel drive or something exotic, and your truck is fairly new, you could of had the rotors turned, for about $10 each if they ne ... 2002 Chevrolet Tracker


... 1990 Ford F350

I am trying to get parts for my brakes. The person at the counter wants to know if I have Drums or roters on the front and wether it's ABS or not. the car is a 1996 Toyota Previa. any help would be appriciated.

The 96 has rotors on the front. Most likely yours has ABS as well. ... 1996 Toyota Previa

How do i take the roters off the front so i can replace the brake pads?

Hi, The truth is you dont have to remove the rotor to replace the brake pads. You will have to remove the caliper, as soon as you remove that. the pads are sometimes attached or just fall off. If the rotor is not damaged then put the new pads on and ... 1998 Oldsmobile Intrigue

I have an automatic 1996 Honda Accord LX (don't know the engine size but it's not a V6) with about 200,000 miles on it. It's been a great car and I commute to and from school 5 days a week with it, about 120 miles a day. At the end of last week, I had extensive work done by a mechanic I've been taking my car to for 7ish years - timing belt & water pump replacement, radiator replacement, fixing some oil leaks, front brakes, roters - $1700 worth of work. On my way home from the mechanic (he's in a

Thanks for choosing FixYa and welcome. First, sorry about your luck. It sounds like you have had some bad luck my friend. Hope it gets better. Here is the thing, If the cap was missing, that is how the oil came out of course. I wasn't su ... 1996 Honda Accord
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.5104 seconds