Having problems with your 2001 Lincoln LS ?

After i took the bolt off the harmonic balancer and the washer came off the harmonic balancer still will not budge on my 2001 lincoln ls V-6 model what am i missing?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

You'll probably need to use a large gear puller - the balancer may be forced onto the crankshaft by the center bolt.
Repair Help & Product Troubleshooting for 2001 Lincoln LS

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After i took the bolt off the harmonic balancer and the washer came off the harmonic balancer still will not budge on my 2001 lincoln ls V-6 model what am i missing?


You'll probably need to use a large gear puller - the balancer may be forced onto the crankshaft by the center bolt. ... 2001 Lincoln LS

No treads on harmonic balancer. Should there be treads on the harmonic balancer because my serpentine belt came off and upon reinstalation properly I found that the belt had treads on the serpentine belt, but nothing on the harmonic balancer. Is the harmonic balancer missing treads or is this a recall, defect, or a broken harmonic balancer, missing treads. v6 3.5 twin cam engine, 2001 Oldsmobile Aurora


The pulley on the crankshaft should have grooves in it for the belt, otherwise the belt will not turn. is the pulley broken off, get back to me. there are NO technical servise bulletins on this item,if you need more help get back to me, Thanks Ray ... 2001 Oldsmobile Aurora

My 2001 Montero sport 3.0 is missing. I have replaced all plugs and plug wires and two ignition coils. The computer says multiple miss fires. I recently had to replace the timing belt and re enstall the harmonic balance. the cam sensor came off and I reenstalled it. Any Ideas.By now i'm thinking the sensor may have slipped. It cranks easy but sometimes, usually when its warm it acts as if it doesn't want too.


Please follow this LINK and read about the causes and repairs of engine misfires. ... Mitsubishi Cars & Trucks

1990 Jeep Cherokee with L6 4.0 engine. The sleeve that is on the harmonic balance came off. Does harmonic balancer have to be replaced or is there a sleeve kit available that can be put on the existing harmonic balancer?


I dont think its repairable. Once they come apart, u have to toss it. Anything is "fixable" but its not worth your time or energy. It will definitely fall apart again. Now's your chanch to put in a performance one. If $$ is an issue, get one from th ... Jeep Cherokee

Hi, I have a question is the harmonic balancer suppose to jiggle? When I am driving my Holden Commodore VS 96 model it sounds good until I put my foot down on the pedal and 1/4 way down it starts to make a whistle sound.. Is this in relation to the harmonic balancer or is it another problem? Also could you get back to me if the harmonic balancer is suppose to jiggle!! Thank you Regards Kelly


I put on a new harmonic balancer and a crank sensor an my car still vibrates what could the problem be. ... 1988 Oldsmobile Toronado

Lincoln ls harmonic balancer part #


Although i would love to do so i cannot confirm that at this time. the part does not fit the 2006 lincoln ls but can be used on the ford crown victoria. the part ran at about a hundred and thirty dollars but there is also equipment required for ... Cars & Trucks

Harmonic balncer my harmonic balncer came undone one day it unbolted itself the main bolt came undone and there seems to be a hole were a pin was going through the harmonic balancer into the crankshaft i believe the pin im assuming broke somone told me i had to replace the cam shaft key and another told me that i didnt have to i need your help in determining the problem


Hi there,\015\012it seems that your explanation is a little bit confusing. Could you tell me what engine( 4D56??) and describe a little bit more in details about the pin you are worried about?\015\012Cheers ... 2002 Mitsubishi Montero Sport

Harmonic balance I am trying to replace head gasket, cannot get harmonic balance off the motor. Tried two different pullers, the thing will not budge. We even tried heating it with a torch for over 20 minutes, it still would not come off. Any suggestions.


You'll have to get the Chrysler balancer puller. Yes, they have a special one for that brand of car. This will make life easier for you. ... 1996 Dodge Avenger

Harmonic balancer when the vehicle is running it makes a horrible screeching sound from the belt/pulley area combined with a bad clicking as if the bearings were messed up. i was told it was the harmonic balancer but i cant find any information about it and in some place it says there is not one on the model but my mechanic says there is one one every car. PLEASE HELP!!!


Not too familiar with the hyundai brand vehicle but i can tell you what a harmonic balancer is and where it should be located. it is the large pulley located on the bottom of the engine it should have marks on it to indicate top dead center. it will ... 2002 Hyundai Santa Fe

I cannot remove the harmonic balancer. What am I doing wrong? We have tried the harmonic balancer puller and it simply isn't budging. Please help?


You need a dodge puller it is the only type of puller you can use. when you get one you will see it comes with a set of shafts that go in the bolt hole to push ageist, a 1/2 impact also helps they are tight....GOOD LUCK ... 2000 Dodge Stratus

Harmonic balancer bolt came off while driving


Not all of them have a woodruff key, but yours may still be on the crankshaft if you had one. At one time, someone had that pulley off and did not tighten the bolt tight enough-they need to be very tight according to specs, over 100 ft. lbs. of torq ... Cars & Trucks

Harmonic balancer came apart while driving how do i fix


By 2nd hand one fit the right socket on the front of the pulley flik your ignition for 1 second to se the rotesion of the engine and go with the socket the opposite site you need force 150-200 punds to unlock it. ... 1998 Honda Civic

Where is the "0" degree mark on the harmonic balancer of a 1991 ford ranger 3.0


... Ford Cars & Trucks

PO336 code My wife drives a 98 malibu LS 3.1 V6. Last week the check engine light came on and showed a PO336 error code. I had the crankshaft position sensor and the harmonic balancer replace. The code was then cleared. The check engine light came back on after just a few minutes. What else could cause this code?


Cam Sensor ... 1998 Chevrolet Malibu

2001 dodge stratus r/t 3.o liter outside pulley on harmonic balancer fell off. do i need whole new balancer or is there something that came off that holds it on?


ON most engines there is only on pulley as part of the harmonic balancer. It is the on that has the rubber between the pulley and the center bit on the crank. Any other pulleys are normally bolted to this pulley on the center hub piece . I'm thinking ... 2001 Dodge Stratus

I have a 2004 Lincoln avaitor and this week i noticed after sunday filling up with gas it started missing on my way to work monday am. when i got to about 40 to 60 mph the truck starts missing. It has 75k miles on it and i thought well maybe it needed a tune up. i got it out of the shop yesterday and it is still doing the same thin only now it has a rough idle and when I stop at a light it acts like it wnats to stale. I noticed too this am the emissions service light came on. Could this be bad g


Once scanned and the codes suggest missfiring, Check your ignition coils. There are one unit atop the each sparkplug, and it is recommended to replace all upon performing a tune-up (costly). Purchase them on ebay and save $$!!Ford/Lincoln/Murcury veh ... 2004 Lincoln Aviator

Miss Firing My jeep start miss fire no power My Jeep Grand Cherokee 1998 ZJ Model start to Misfiring. When diagnose it came up with an error System too lean. Please give me the different cause why jeep mis fire and possible solutions


You might have a small leak in your vacuum system, check all of the hoses and plugged vacuum connections. Check your plugs and wires, distributor cap and rotor. Sometimes a crack in the distributor cap will cause carbon to build up. Since carbon is a ... 1998 Jeep Grand Cherokee

Hello, I have a Peugeot 307 1.6lt 2002 model. The car has been demonstrating lagging during acceleration, rough gear change an sometimes stalls when idleing. Recently the car's diagnostics light came on an sai my catalytic converter was failing. When this light came on the steering wheel shuttered. I suspect the problem is due to my catalytic converter been blocked due to fouled spark plugs, or the association of miss firing which woul be causing the engin to lag an have rough acceleration


... 2002 Peugeot 307

Trying to change crank sensor cant get harmonic balancer off no puller i can find will fit in slots on balancer does it require specialtool for this model


... 1994 Pontiac Bonneville

Long story but detailed to assist proper diagnosis. Noisey harmonic balancer was replaced at local shop with correct new balancer, key was messed up, shop said he had to remove timing cover to replace messed up key. Both sensors replaced, new timing chain, since we were in the same area and car has 102,000, all was replaced, vehicle ran for about 25 miles and quit. Went back to shop, said not his problem. Had other shop look at vechicle, went to start vehicle and gm code 58 came up, tested key k


Dodge neon 2005 as code p0300 engine keeps chuk cunk...like jieking ... 1992 Pontiac Bonneville

Parts missing lincoln town car 1990 needs a grille ordered one however no other parts came just the grille can't figure out what is missing. spent a lot of money for a header panel and grille header panel is on but grille has nothing to attach it with what is wrong please help


The grill is held on in place by the two springs pushing on to it from the grill pannel it sits in. ... 1990 Lincoln Town Car

2005 lincoln harmonic balancer wobbles


... 2005 Lincoln LS

Harmonic balance came off, now car won't start


Did you put the keyway back on the crank before you put the harmonic balancer back on.\015\012the key goes in the groove on the shaft and balancer ... 1996 Mitsubishi 3000GT

I have a 1990 corvette with what seems to be an un fixable problem. I've had 3 shops tell me they don't know what's wrong with it. They tell me , they can't set the timeing corectly due to when you unhook the wire from the computor to the distributor and line the rotor with number 1 top dead center the line on the harmonic balancer is out of site. They all rule out a timeing chain issue and said the distributor was in good condition. The car runs like **** , it misses and spits and sputters.


Replace the harmonic balancer so a mechanic can line it up correctly. If you take it to an expert (I know one here in Southern California) he should be able to set the timing by trial and error\015\012\015\012Here is a replacement:\ ... 1990 Chevrolet Corvette

Harmonic Balancer Pulley came off while driving. How do i put it back on? Is it a press fit, or do i have to replace HB?


\015\012Do you also have and oil leak that has kept this part wet with oil?\015\012\015\012The Harmonic Balancer is a replacement item.\015\012\015\012Hope this tip helps\015\012\015\012r/\015\012David ... 2003 Hyundai Santa Fe
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6935 seconds