Having problems with your 2001 Jeep Grand Cherokee ?

Ignition switch installation where is it - 2001 Jeep Grand Cherokee

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

You need a torex screw driver take the cowling off around the steering wheel thare are 3 screws also un screw the tilt lever grab it with your hand and unscrew it you will see the ignition it has two plugs that come off very easy the rest comes out with the torex hope this helps good luck
Repair Help & Product Troubleshooting for 2001 Jeep Grand Cherokee

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to install ignition switch 1996 grand jeep cherokee 4.0


... Cars & Trucks

Ignition switch installation where is it - 2001 Jeep Grand Cherokee


You need a torex screw driver take the cowling off around the steering wheel thare are 3 screws also un screw the tilt lever grab it with your hand and unscrew it you will see the ignition it has two plugs that ... 2001 Jeep Grand Cherokee

Install Ignition switch in a 1999 jeep grand cherokee, now it would not start and the key light is flashing


Probably because the new key has a different code chip than the one that came with the Jeep when it was new.You would need to have a new key to fit the new lock cylinder that matches the old chip. ... Cars & Trucks

When key is in the Problem with the Jeep Grand Cherokee 1996 Grand Cherokee when key is in the "on" position my dash lights (check engine, brake, etc) will run their post and then the normal lights will remain on, however my instrument panel doesn't operate at all. The fuel light will come on to indicate that the tank is empty...even though there is a half tank. I've checked the ignition switch, and ignition cylinder. I have replaced the relay for the fuel and starter. I have replace the fuel fi


Well I have never had this problem with a jeep but I have had this problem with some Chrysler mini vans the same year. The problem always ended up being a cold solder on the instrument panel itself. If I resoled the pins on the back of the circuit bo ... 1996 Jeep Grand Cherokee

1993 Jeep Grand Cherokee will start then immediately die. I've replaced the Crankshaft sensor, ignition coil, fuel filter, battery, new plugs and wires, new cap and rotor, tried swapping the fuel pump relay with the auto shutdown relay and installed a new ECU computer. Before installing a new computer the jeep would crank but not start. After installing the new computer the car started right up. I then attached the vacuum hoses to the air cleaner assembly and now it won't keep running. Any ideas


This sounds like a imobiliser problem,sit in the car,lock the doors on the key fob then open them on the key fob,you have about 2 minutes to start the car or it will activate the imobiliser.had the same trouble. ... 1993 Jeep Grand Cherokee

I need to run the fan wire to the ignition switch where is the ignition switch located on a 2003 jeep grand cherokee laredo


Sounds like you need tests run at the fanswitch which is screwed into the head. sounds like you need the updates for your vehicles wiring and the tsb's that pertain to the correct identification of parts, wires and switches. you may need a thermosta ... 2003 Jeep Grand Cherokee

How to install a brake light switch on a Grand Jeep Cherokee


Dont do it... It will take you bout 30 minutes to remove and replace it on the steering column ... 2001 Jeep Grand Cherokee

My 98 jeep grand cherokee wont start. It doesnt even click or turn over. battery is fine, headlights, dome lights, all go on. Radio doesnt work with ignition on. I checked ALL the fuses, I replaced the starter, ignition relay box, ignition switch and STILL nothing???? I dont believe im getting any power from the ignition to the starter. Any suggestions?


Fuse 8 40a supplies power to starter relay and ignition switch, to close the starter solenoid and engage the starter which draws directly from the battery. check to see that the starter relay is closing, if not ensure that the park neutral switch is ... 1998 Jeep Cherokee

I have a 2003 Jeep Grand Cherokee 6 cyl. I am getting fault codes P0351,P0352 and P0353 which is defined as #1,#2 and#3 ignition coil circuit and code P0505 JEEP Idle Control System Malfunction and code P1495 JEEP EVAP Leak Detection Pump Solenoid Circuit Condition. The problem I'm having is at times the engine will bog down and lose all power and sometimes just completly quits. I can stop the vechicle and turn the key switch off and start the engine and it will run just fine. I have replac


I would check Cam Position Sensor as is directly related with ignition. Power loss is due to the ECU going on "limp mode" to prevent further damage.I hope this helps! ... 2003 Jeep Grand Cherokee

I have a 1995 Jeep Grand Cherokee Laredo 5.2 L V8, I got in my Jeep today, started it up and it was fine, later went to do the same thing later and the was a clicking sound behind the glove box, the Vic computer screen doesn't turn on, and I can't turn any lights on in cab. The light in the very back of the cab is lit, and uncontrollable, and the only position on the ignition switch it doesn't click on is the 'ON' position.


... Cars & Trucks

I have a 94 Jeep Grand Cherokee with a 2 button viper remote start on it. The remote system includes a kill switch on my ignition. It worked fine but now the kill switch turns on randomly and won't disengage. How do I reprogram my remote start? It's a very old system with a square black remote with two gray buttons on it. The only info on the con says dci.


... Cars & Trucks

93 jeep ignition switch - 2006 Jeep Grand Cherokee


... 2006 Jeep Grand Cherokee

I have a 2003 Jeep Grand Cherokee and the ignition switch seems to be getting bad. I can usually get it to start by jiggling the key around and sliding it in and out while turning it. It will start right away if I get the key just right otherwise, I get nothing, no dash or accessory lights or indicators. Does this sound like a switch going bad or an electrical problem? Mechanic not listening to me.


It sounds like the ignition cylinder itself is worn and needs replacement. the fact that you cant turn the key. thing that can cause this is if you have to many keys on your key chain . ... 2003 Jeep Grand Cherokee

My vehicle is a 1996 jeep grand cherokee when I turned on the ignition to start it, it feels like it does not go all the way over in start position. But can turn the key on and jump start the starter with the screw driver and it will start..... does this mean my IGNITION SWITCH CAN BE BAD? Thank you Robert


It could be or solonoid you jump is bad try banging solonoid might unstick when turn to start if lights dim switch is fine ... 1996 Jeep Cherokee

I have a 1996 jeep grand cherokee,turn signals dont work. I bought the car this way. ive replaced the flasher, the ignition switch and the multi function switch. ive check all the fuses and they are good, ive also checked continuity from positve cable to the fuses and got continuity to all evcept 1, but the diagram in the owners manual and the haynes manual are incorrect. any ideas?


Since the lights are also tied to the hazard system, If the hazards do not work either then you will need to check for ground at each light ... Jeep Grand Cherokee

I have a 1998 Jeep Grand Cherokee Laredo. It will not start. After checking fuses then changing the ignition switch on console I still can not get anything to light up on the dash when I turn the key, Someone told me that it is probably the on board computer. Is there anyway to check that system or do I need to buy one to find out. Thank you for your help. 160.000 mile Cherokee owner


Hello jam... you need to have your jeep's computer scanned for error codes. many auto parts stores, even AAMCO shops now scan for free. Start there. Joe ... 1998 Jeep Grand Cherokee

Our 1995 jeep grand cherokee kept stalling. Trying to fix it we have replaced the computer, and now the ignition switch. Now the jeep will start, but as soon as you let go of the key, it stalls. Any suggestions?


Check the relays under the engine. Swich them around and see if it will actually run when you switch them/ Try ALL relays. I just had to do this on my 90 cherokee. The relays are only a couple bucks at any autoparts store. They are usually square sha ... 1995 Jeep Grand Cherokee

How to remove broken ignition lock from ignition switch on 1997 jeep grand cherokee


... Jeep Grand Cherokee

1995 Jeep Grand Cherokee Ignition Switch Repai


If you can find a match in a local scrapyard it should be a bolt it-plug in item...get a manual so you can deal safely with the airbag. if you have one. ... 1995 Jeep Grand Cherokee

Ignition switch for 2000 jeep grand cherokee is stuck


I'm going to answer this question since I don't know how the security system would affect the lock.If you can get the key out of the lock, you may want to spray some WD40 or other lube in the slot where the key goes.If that does not help, yo ... 1999 Jeep Grand Cherokee

The ignition switch for 2000 jeep grand cherokee is stuck will not turn


... 2000 Jeep Grand Cherokee

2005 jeep grand cherokee 3.7 liter will not start. Did start without touching the key. Had a new starter and battery 1 year ago. seems like ignition switch but relay clicks on relay panel when trying


... Cars & Trucks

How do i change ignition switch the key cylinder on 95 jeep grand cherokee limited


Disconnect the battery (or while the cylinder is out your radio and stuff will be on).\015\012If you can manage to get the key to turn to the starting position\015\012(you do not need to start the car)... I had a problem where my key\015\012wou ... 1995 Jeep Grand Cherokee

2002 Jeep Grand Cherokee. The overhead console display works intermitently? It does seem to come on (after switching the ignition off and on again) after the vehicle warms up a few minutes? Any ideas?


This is a very common problem with many of the mid 2000 truck and SUV overhead consoles. The console is very prone to internal failure. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com There ... 1999 Jeep Cherokee

Ignition switch turns freely - 1996 Jeep Grand Cherokee


Broken ignition tumbler -- replace tumbler assy ... 1996 Jeep Grand Cherokee
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.6327 seconds