Having problems with your 2001 Hyundai Sonata ?

Hi my car has an issue with the clutch, the car does take load or initial pickup

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Sounds like the clutch disk is worn out.
Repair Help & Product Troubleshooting for 2001 Hyundai Sonata

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi my car has an issue with the clutch, the car does take load or initial pickup


Sounds like the clutch disk is worn out. ... 2001 Hyundai Sonata

1997 saab convetible manual transmission stuck in reverse key wont turn, initially parked the car do to clutch problems. When parked the key would still turn and could move gear shift, battery died and after I charged it and put it back in the key and clutch issue happened. I need to kove the car for repair is there a way to get it out of reverse


... Cars & Trucks

How do I know if I have a bad clutch or if it is a transmission issue? The clutch didn't "Snap" or anything, but when I shift... the car takes a few seconds (RPM's do ramp up) to get going each time I shift. You can feel it kick in after about 3-5 seconds! 1997 Jetts GLX


Put car in 3rd gear and release clutch pedal slowly,if car stalls then its not the clutch... ... 1997 Volkswagen Jetta

Starting Problems Stated before, my car will sometimes not start immediately after turning the key, I take out the key and try again and usually it will start. I already replaced the Clutch pedal ignition lock switch and the starter relay. I don't think it is the starter cause I have experienced starter issues with other cars. What else can be the problem? Thanks, David


Try checking all the battery cables and cables to yoiur starter making sure they are clean & tight. ... 2003 Mitsubishi Lancer

I cannot take a phone call now but did pay for that,, I want to find out what the problem is with my pickup truck. I have a 1995 Chevy with the 6.2 turbo in it.. NOW when pulling a load up a hill it blows very black smoke SO BLACK taht cars cannot even see.. When i take trailer off i see black all over the trailer and appers to be fuel as well. ITS a mess of course.. This never started until a couple months ago.. I checked everything under the hood and it appears no leaks.. CAN you suggest if yo


You are going to find the pump needs rebuilt ... GMC Sierra 3500

My car is very new about 8 weeks old but the last couple of weeks it intermitently keeps losing power just like fuel starvation if u put ur foot down it goes again sometimes also if u take load of engine like press clutch down rev engine and try again it sometimes cures it please help


If this is a new car you should take it in for warranty, but the year u selected is 2001, the most common cause of this type of problem is a MAF (Mass Airflow) sensor, this sensor is located in the large flexible ... 2001 Hyundai Accent

I just got a 93 manual 5 speed v6 4cam camry...barely made it home as it was in every gear hardly moving with really high rpm. I am going to add some dot 3 break fluid as it is low. I hope this works, it was fine yesterday. I do not really understand how it can be in gear and not move? Is this a clutch disk issue, can I make an adjustment?? PLEASE HELP! I have put everything into this car that I have because I need to get to and fro work, laundry, take my children everywhere ...ect. thank you!!


I am sorry to say that this is a classic sign of a worn clutch. You most likely need a new clutch, consisting of a driven plate and pressure plate. It is possible also that your clutch pedal travel is out of adjustment, and it is not moving far enoug ... 1993 Toyota Camry V6

When starting up my 2000 Corolla cold, it will stall out if I hit the gas pedal too soon. It can take up to 1-2 minutes before the car has enough "power" when I put on my gas pedel to move and not stall out. This is not an issue after the initial warm up. Any suggestions?


This sounds like a computer fault The electronic version of the choke not working There's a sensor on the thermostat housing with 2 wires going to it That's the sensor that tells the computer the engine temp May be faulty ... 2000 Toyota Corolla

AC Repair How do you find the clutch in the compresser. I want to try to do it on my own but need information. Also I am having issues with misfires. When I drive on the interstate it is fine but when I drive on the regular road my car takes a while to get to speed to the point were it feels like it will stop. Does anyone have any idea what this is?


A/c clutch located in front of the a/c compressor ... Volvo S90

Ok so i have a 2000 elantra and the clutch keeps slipping. the issue started after i got the car figured it needed a clutch so i had one put in. to my surprise i get a call saying that the clutch was brand new. told them to put it in anyway. about a month after the clutch was installed the issue returtned. tried another clutch thinking it was something with the kit .. so here i sit 2 clutches, and a slave cylinder later and i still have this slipping issue .. it seems to go away for a short


It might be the flywheel make sure there are no oil leaks and clutch isn't contaminated does the gearbox select gears ok when it starts to slip before you re-bleed it? ... 2000 Hyundai Elantra

Clutch shudder I have a '97 Subaru Outback Legacy. 2 weeks after I bought it the head gasket blew. During that repair I had the mechanic replace the worn clutch as well. Ever since the car develops, no it is not there after every fix, a shudder in first AFTER the car warms up. About the third time I was going to take the car back again for the same problem, the clutch threw a spring and froze my clutch. I destroyed my 2nd gear getting of the highway. I then took the car back to the same me


Ask the mechanic if the clutches both came from the same source and if they were rebuilt units from the same re-manufacturer. The material used to resurface a clutch can cause this results. ... 1997 Subaru Legacy

I have got the flywheel resurfaced put it on bought a new clutch pressure plate,clutch,and throw out bearring..put rebuilt transmission,put transmission in bolted everything back the gears change in the tranny when the car is off..but when you put it in first push the clutch to the floor go to start the car the car tries to take off,..I kno the clutch isnt disengaging I jus cant figure out why its not and I have blead the slave cylender.. please help ???


Does the clutch pedal have pressure as soon as you push it or is it going beyond halfway down before you feel the pressure? ... 1984 Chevrolet Camaro

Hi All! I have a 2000 Mercury Sable, a DOHC 24 valve engine. I have an issue with 1,2,3 cylinders. They misfire especially when the car is cold. When the car starts initially, the RPMs go under a 1000 and the car shakes badly due to engine. There is also a gas odor once the car is initiated. Once I increase speed, for instance on the highway, the car is fine, but if the speed is unsteady and I have to make stops at the lights, the engine goes off and the car dies. On this model, any spark plug h


The air fuel control mod can cause the prob you are having 1990 to 2000 ford rangers are bad about doing what yours is doing and it is always that air fuel mod ... 2000 Mercury Sable

Clutch issues I have a 2006 Saturn vue. I went to get gas today and the clutch was all the way up. When I went to get into the car to leave the gas station I had trouble putting it in first gear. I made it home and parked it. When I went to run another errand the car would start but when I pushed down on the clutch to put into first, the car would make a grinding sound and would not move out of first or let me change into any gears.


This is a hydraulic clutch, meaning you push fluid to make the clutch move just like the brakes.I would check the clutch master cylinder first to see if it is full of fluid.The master or slave cylinder could have failed, among other things. ... 2006 Saturn Vue

Previously had a oil leak which damaged my engine i had a new engine put in my car in March and then 16 weeks later my car was still leaking oil and the car would not go into 1st 2nd or reverse the garage man told me that it was the clutch so 4 weeks ago he put a new clutch in and said he has stop the leak now it is leaking loads and will not go into gear at all he said it is my brake cyclinder and also the cyclinder from the clutch which caused pressure.also i still have a leak in my engine, wh


I would take it back to the garage that put the clutch in. The car not going into 1st, 2nd, or reverse is a transmission problem not an engine problem.\015\012\015\012I would take it back to the garage that put the engine to verify whethe ... 1999 BMW 318 ti

2007 HYUNDAI ELANTRA 5spd. TRANS. ISSUE Hello, my name is Kevin:On my 2007 Elantra I had the through out bearing replaced twice by the dealer for a churpping noise. The noise came back a month later so now the dealer replaced the whole clutch. When I picked it up in the a.m. from the dealer it was a cold day, in the 40's I went to start the car with it in NEUTRAL, I pressed the clutch pedal down, the car started, I then came up on the clutch pedal, the car begain to move forward. I quickly s


HiI think the dealer may be trying to fob you off, have them check the slave cylinder on the clutch / gearbox and ensure the fluid has no air locks in it. this can cause the issue you are having. Also have the pipes checked out any pinhol ... 1993 Toyota Pickup

CLUTCH ISSUES I have a 2004 ford mustang V6...Pony....when I turn the car on, it makes a lous squeeling....and when you press the clutch it starts grinding....I know it has something to do with the clutch, but my question is where do you put the clutch oil? People say it by the brake cylinder....but I don't see it! Or its under the car on the transmission? So my question is where do I put oil for the clutch?...oh.....and it still catches all gears....so I know it's not the tranny? Please help me


You are referring to the clutch master cylinder it takes brake fluid. it is closer to the fender by master cylnder. sounds like you have a release bearing going bad ... 2004 Ford Mustang

Synchronizer I just had the clutch on my 2004, 5 speed Toyota Corolla replaced. My car now makes a grinding g sound only when I shift into 3rd gear. If I shift slowly into 3rd, I seldom grinds. It always grinds when I downshift into 3rd gear. Should I have the repair shop that replaced my clutch fix this issue at no cost( the shop knew it was grinding when I picked it up and it cost me 1K to replace the clutch? I drove the car when the clutch "went out" to get it to the garage (about 10 miles),


... Toyota Corolla

Multiple issues The first issue is that the car wont start cold. It takes multiple cranks before it will start up. But during the summer months it starts fine. Another issue is that the car has started to overheat. It doesn't last long before you can start it again and start driving. The check engine light has turned on and off in the last few months. Are the two issues related? And if not, what could the problem be?


I doubt the issues are related, but you need to get the computer scanned for trouble codes first.The codes may point you in the right direction to diagnose the problems.It's possible the engine temp sensor is faulty which could cause both pro ... 1996 Chrysler Town & Country

I have a Toyota Corolla 2000 model. Initially starting the car it will idle until I put it in gear and release the clutch. When the clutch is released the car dies, then when I start the car up again it will die out 2 seconds later! Any solution?


That sounds like dirt in filters of the fuell.rpm too lowCO too low or too high ... Cars & Trucks

Have a 1992 eagle talon fwd turbo when u start the car and try to put it in gear it grinds really bad and if the car is in gear when u start it the car takes off and rolls with the clutch to the floor ive changed the slave and master and adjusted the clutch the pedal acts like it has a lot of play at the top then u get to the friction just dnt no wuts rong can somone help me plez


Sounds like the throwout bearing has fallen off the guides ... 1992 Eagle Talon

I have a 1992 Lexus ES 300. Automatic. It has 130,000 miles on it. I bought it about a year ago and have had so many problems with it ever since I bought it. My most recent issues with it is when i go to start the car it usually takes 3 or 4 tries of turning the key over before the car starts. It doesn't even make any noise of the engine turning over and i hear a click each time. I am affraid soon it won't start at all. The other issue i am having with it is when i begin to drive the car jerks b


Your first problem sounds like starter solenoid. Replace starter should fix your problem. Second problem sounds like a misfire possibly? Change plugs wires, cap rotor. ... 1997 Dodge Intrepid

Just replaced the clutch because the car wasnt going in to gear without force and grinding. replace the clutch and still the same problem. even pulle the arm manually witha bar to release it and still no luck. there was a sleave like peace on the center of the flywheel that was chewed up but didnt seem to affect the way the clutch set against the flywheel. could it be an issue? i wouldnt think that the synchronizers could be bad on the gears especially with the car not in motion


That center piece is the pilot bearing, the input shaft should ride free , if it is indeed chewed up the shaft is probably binding in the flywheel ... 2003 Hyundai Tiburon

Today my grand marquis had battery issues. i was parked for about 20 minutes with car on then i turned off then right back on to take off but the car would not start- i can tell it was a battery problem but some of the lights in the car did work-but i would not turn on to put in drive-i messed with headlight swith and all of a sudden smoke was coming out of the hood-is this battery issue or alternator? I had someon pass me cables real quik and it didnt wrk-so a little later i passed cables again


Check your battery posts. Over time, they tend to corrode and cause an inproper connection, but your vehicle is fairly new. If they are dirty, get a wirebrush and clean them thouroughly. Also, make sure the posts are tight and not loose. If they're c ... 2006 Mercury Grand Marquis

How long does it take to replace a clutch on a 1991 toyota pickup 4 wheel drive 6 cylinder 3.0 liter engine? The clutch burnt out and I'd like to know how many hours labor it would be to replace it because I want to just walk into the repair shop and say "Here. Here's a brand new clutch and it'll only take ___ hours to replace. So I don't want any excuses."


... 1991 Toyota Pickup
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3459 seconds