Having problems with your 2001 GMC Jimmy ?

Remove C Clip from GMC?

\015 It does not drop out,I have tried every tool in creation! No luck!\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2001 GMC Jimmy

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is there a tool to remove a spring round clip thats holding the brake switch on a pin to my 99 GMC yukon? If not....What is the best tool and fastest way to remove the clip off the pin?


Needle nose pliers ... 1995 GMC Yukon

1997 GMC Sierra 1500...how do I remove the clip that attahces brake light switch to the brake pedal? There is not much room there to work with to tools I have. Do I need a special tool or do I need to remove something to gain access?


I HAVE DONE THIS. WHAT A PAIN. I USE A COTTER PIN PULLER. IT HAS A SCREWDRIVER HANDLE, 8 OR 9 INCHES LONG, WITH A RIGHT ANGLE POINTED END. TEAR IT OFF ANY WAY YOU CAN. WHEN THE NEW SWITCH IS IN PLACE, I USE A FLAT WASHER & THE RIGHT SIZE HAIRPIN ... 1997 GMC Sierra

Brake switch clip removal - 1995 GMC Sierra C1500


... 1995 GMC Sierra C1500

On 98 gmc pickup how to remove retainer clip from break pedel and power booster


... 1998 GMC Sierra

How do I remove the front clip on an 89 GMC Suburban 1500 4X4 to facilate engine access?


Its alot alot of work but the whole nose will come off cab and frame in one piece ... 1989 GMC Suburban

How do I remove the rear brake light cover on 1990 GMC Sierra 2500 to change bulbs? Are there clips inside-specific places to pry it off? Thanks


\015\012\015\012\015\012I hope these instructions match your model. \015\012\015\012\015\012Lower the ta ... 1990 GMC Sierra

Remove C Clip from GMC?


... 2001 GMC Jimmy

How to remove a sunvisor retainer clip for a gmc 3500


... Cars & Trucks

How to remove GMC 2006 Sierra door speaker? I have the door panel off but don't see any screws or mount unless it's "clipped in" I am trying to isloate speaker or tweeter issue.


... GMC Sierra 1500

How do you install the hatch struts in a 2000 ML320? It looks fairly straight forward but I can't remove the ends from the ball joints. - Do I have to remove the clips in the ends of the struts to remove them from the vehicle? - I assume that once I get the old struts off, I can just pop the new ones one without removing the clips? Any help is appreciated. Thanks!


To remove take off the old clips.makes life easy. ... 2000 Mercedes-Benz M-Class

How do I remove the C-clips on a 10 inch rear diff with lock-up . I need to replace the axle seals. I have removed the lock pin and the main spider gear pin but can't seem to remove the centre piece that allows the removal of the C-clips


Once the pin is out, push the axle in towards the middle of the car, the clips may now come out, even fall out maybe. remove the clip, then pull the axle out. be sure that the axle bearing surface is good, any pitting or grooves and the axle and bear ... GMC Savanna

My speed ometer stopped working. I traced the cable from the dash to the transfer case and the speed sensor was loose. I was able to remove it by hand. it turns out thatthe threads were striped and I am not sure what I am getting into when I remove the retainer clip that holds the bolt like peice that I believe holds the gear in the transfer case. can I simply remove the retainer clip and replace the gear? If so my thought was to remove it and use lock tight and catch some threads when re mounti


Best bet would be to replace the sensor if its threads are stripped. ... 1992 Jeep Cherokee Sport

How do I remove the cooling fan from my 1998 pontiac sunfire? I have removed the wiring clip, removed the bolt on the bottom and freed it from its clips but it still wont come off. It is very loose but is hung up on something.


... 1998 Pontiac Sunfire

I'm trying to remove the left rear axle so I can replace the outer oil/greese seal. Seems pretty straight forward, however I'm not totally sure where the ''C'' c;ip is located that I need to remove to allow the axle to pull out. I have the differential open. Must I remove the spider gears inside of the carrier in order to get the axle out? I'm told there is a ''C'' clip that keeps the axle from pulling out. Is that ''C'' clip behind the gear (between the gaer and carrier wall) on the end of the


Have someone try to move the axle in and out while you watch the end of the axle inside the spider gear carrier. The 'C' clip should be near the end and will drive off with a small punch. If there is no clip, then the axle/bearing is retained by a pl ... 2001 Jeep Grand Cherokee

How to remove fan assembly on 2002 chvy cavalier . i have removed the bolt and thetwo clips on the side. i am having problems with the clip that goes over the radiator


... 2002 Chevrolet Cavalier Coupe

This is on a 1997 Geo Tracker 4-door. The inside door latch cover is broken and causing major problems. My problem is: after removing the philips screw holding the cover on and loosening the assembly, I can not remove the bar that attaches to the latch. I have tried prying off the white clip on the bar and squeezing the clips on the door latch - no go. I need to replace the whole door latch assembly, and am stuck on getting the stupid thing OFF. Thanks for any help you can offer!


Most of the white clips on the bars twist upward and the bar pulls out of it. ... 1997 Geo Tracker 2 Door

My husband tried to remove a child's carseat without undoing a clip that routes the belt, and pulled it so tight that there isn't enough play in the belt to free it from the clip at all. Is there a way to unlock the seat belt without removing the center pillar trim?


You may be able to remove the bottom bolt........Sorry i don't know what u drive.Hope this helps. ... Toyota Highlander Hybrid

How to remove upper transmission line clip from radiator on a 1996 ford taurus? I have undone the retaining clip. Now I'm looking at a plastic plug that's secures the hard line to a large hex nut that's screwed into the radiator. Do I pry the plastic plug out, does it screw out or pull out, do I need a special tool to remove it. Do I take a needlenose pliers and pinch the sides in the pull back the line from the radiator. Thanks Leo


... 1998 Ford Taurus

The drivers door handle on my 2000 Hyundai atos has a cracked black plastic leaver which connects through a white clip to the rod which unlocks the lock. I was wondering how to remove this handle. Do you need a special tool to remove the white clip?


No just a flat blade screw driver the clip should pop off it may have a **** shell type which you pop **** shell open and pop off rod ... 2000 Hyundai Accent

I'm trying to remove the right rear axle from a 1981 Olds Delta 88 and can't figure out how to remove the retaining clip that holds the axle to the rear end. Is there a special tool or trick to getting the clip out?


Unbolt the pinion shaft bolt -slid the pinion shaft out -then either with help or yourself push the axle[at the flange] inward than remove "C" clip go back to axle and slid it out to take out other side same push in axle remove clip and slid out ... 1983 Oldsmobile Delta 88

My passenger window was smashed with a bottle (nice eh!) and need to change the glass. I am having problems removing the passenger door interior. I have removed the screws and clips but it is stuck around the window winder and do not want to force the clips. Any help much appreciated. Nola


You need to take the window crank off.  There should either be a screw/bolt going straight into the handle where it is attached to the door (there may be a cover over it) or a clip on the back of the handle.  If there is no screw pry the ha ... 1991 Toyota Corolla

Trying to replace rear turn signal light by following manual...which I can usually do..however we can't seem to get past removing the 2 screws...it has proven very difficult to find the clips that it says we should be able to slide off to locate access to the tail light . The owner's manual is long winded... 1. Remove the two inboard nuts on the assembly. 2. Pull side assembly rearward to clear studs. 3. Rotate side assembly on the outboard side releasing the upper clip. 4. Slide assembly slight


They are on a rail, after removing the screws it should slide towards you. Since it just wiggles, there are small plastic studs that keep it in place. I you need to pull it towards the front of the car or 90deg out from the front of the van. ... Chevrolet Express

I can not remove my old fuel filter on my 1997 chevy cavalier. The filter has the pastic clip that I can see, but when I push on the plastic clip it won't release so I can remove the filter. Any help would be great! Jess


You need to try to jam something like a flat head screw driver and get a good grip on that oil filter.\015\012\015\012-david ... 1997 Chevrolet Cavalier

I am attempting to replace the low beam headlight bulb on a 2005 Buick Allure. I have managed to raise the plastic clip holding the assembly in place. I have removed the screw and raised the metal clip also holding the assembly in place. I have removed the plastic pin and pulled out the coloured plastic strip between the high and low beams, but I do not seem to have enough room to move the assembly forward to get at the bulb for replacement. Any suggestions?


... 2005 Buick LaCrosse

99 Tahoe.. How to remove front grill so I can replace the headlight assembly? I found 2 top screws, 2 screws accessed threw the grill bars, removed L+R park lights and screws behind, and released center snap clip at bottom center.. still stuck.. appears to be 2 more snap clips L+R inside lower grill bars at bottom but haven't figured out how to release these.. still stuck..


... 2007 GMC Yukon Denali
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.1542 seconds