Having problems with your 2001 Ford Taurus ?

Need tightening sequence for head bolts 2001 Ford Taurus SE

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2001 Ford Taurus

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need tightening sequence for head bolts 2001 Ford Taurus SE


... 2001 Ford Taurus

Need tightening pattern sequence for head bolts 2001 Ford Taurus SE


... 2001 Ford Taurus

Head bolt tightening sequence on a 2000 Ford Taurus 3.0 EFI


... 2000 Ford Taurus

96 ford 2.0 dohc head bolt tightening sequence


... 1996 Ford Contour

Head bolt specs 2001 ford taurus 3,0 ohv


... Ford Taurus

What is the sequence to tighten t head bolt for a 1998 ford escort 2.0 engine


... 1995 Ford Contour

Hi , 87 KC ford laser 1.6 sohc , recon head . need to know valve clearances and head bolt torque and tightening order for head bolts also. thanks very much chris


... Ford Laser

Need head bolt numbering for 1993 ford 1.9L engine. already know sequence, just don't know numbering of bolts on head.


Hope this helps\015\012Front to Rear Diver Side\015\012 8-6-2-4-10\015\012Front to Rear Passenger Side\015\012 9-3-1-5-7 ... 1993 Ford Escort 4 Door

Need 1982 ford escort head bolt sequence


... Cars & Trucks

Need info on 3.1 head bolt torque and tightening sequence


... 1997 Chevrolet Lumina

I need torque specs for the heads and the intake for 2000 ford expedition with 4.6l. I also need the tightening sequence for both.


... 2000 Ford Expedition

Torque on 3.0 ford taurus head bolts


40 ftlbs then 73 ftlbs then recheck at 73 ftlbs ... 1999 Ford Taurus

Need torque specs and tightening sequence for cylinder head bolts


... 2000 Plymouth Breeze

I followed the haynes manual to tighten up the head bolts on my 1995 mitsubishi pajero 2.8td exceed, supposedly, tighten up all uniformly to 100NM, back all the bolts off, tighten again to 50 NM, tighten all 90 degrees uniformly, and tighten all 90 degrees once again. However, the head blots I bought could not take 100NM and sheared! Is this definitely the right sequence, or are the bolts I got defective? Many Thnks for reading


Cylinder headRenew bolts Yes Stage 1 Tighten 50 Nm Stage 2 Tighten 100 Nm Stage 3 Slacken off 360° Stage 4 Tighten 50 Nm Stage 5 Tighten 90° Stage 6 Tighten 90° Stage 7 Tighten M8=24 ... 1995 Mitsubishi Diamante

Need torque setings and tightening sequence for punto 1.0 on 51plate cylinder head bolts


Stage 1 20nm,stage 2 30nm and then 90* and another 90* ... 2006 Fiat 124

Need torque specifications for head bolt for 2002 ford taurus


2002 ford Taurus se v-6 head bolts torque and sequence ... 1997 Buick Century

I need torque sequence head bolt ford windstar 2002


... Ford Windstar

Need diagram of head bolt tightening sequence on 2004 dodge stratus 2.4 DOHC


... 2004 Dodge Stratus

I need to know the torque settings for the valve?(top of engine) cover bolts on a Ford Econovan Maxi 1989, FE engine. and tightening sequence


... Ford E-Series

Took my 1997 ford taurus with 3.0L to a shop did a compression check on the back cylinders (1,2,3) 1&2 were at 50 psi. They said more then likely it was the botom end of motor which has the problem. Now wouldnt it blow smoke an burn oil if the piston rings were bad? The head looked fine the block as well, New gasket an bolts were installed tightened to specs. This car runs almost perfect except when u put it in gear it stumbles like it out of timing. Where should i go from here?


Have the shop do a leakdown test and verify the problem, it could be a bad head gasket or a burnt or stuck valve. ... 1997 Ford Taurus

Hi i need to no the torque settings and tightening sequence for the head bolts on a renault laguna 1.8 16v if any one can help please thanks


... 2006 Renault Le Car

Anyone know what the torque for the head bolts on a 1991 ford taurus with the 3.8L engine, need to replace it, but i have no idea what the torque is....please help


Torque sequence: ------------ 6 4 2 8 5 1 3 7 ------------ \015\012Step 1: Torque from 47-53 Nm (35 to 39 Ft/Lbs) Step 2: Back off all bolts 360 Step 3: Torque from 27 -33NM (20 to 24 Ft/Lbs) Step ... 1991 Ford Taurus

I need to know the tightening sequence of the 4d56 diesel engine cylinder head bolts. help me please


Cylinder head sequences are always the same, start in the middle and work out like.....12.8.6.1.3.9.11\012 14.10.4.2.5.7.13. ... Mitsubishi Mighty Max

I need the tighten spects on head,intake and exhaust of a 2000 ford taurus 3.0 flex eng.


Register with Autozone.com for free repair info ... 2000 Ford Taurus

FORD 351 W CYLINDER HEAD BOLT TORQUE SPECIFICATIONS? NEED SEQUENCE.


Torque is 85 ft/lbs of torque. Tighten the bolts starting in the center of the head and working your way out to the ends. Go very slowly and only tighten slightly each time you move from the center to the outside. You must pull the head down very slo ... 1995 Ford F250
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.2448 seconds