Having problems with your 2000 Plymouth Grand Voyager ?

Distributor assembly/camshaft sensor for 2000 Grand Voyager

\015 A mechanic told my husband that the camshaft sensor in our 2000 Plymouth Grand Voyager needs to be replaced. He found one at a local dealer, but was told that the entire disrtibutor assembly would have to be changed at the same time an it would cost $1200.00. Is this the case or can we just replace the sensor?\015
Posted / edited by AnonymousUser on : 15-01-2018

Answers :

You can replace just the cam sensor, I've done it, but it's kind of a delicate job. You have take apart the distributor to do it, it's not hard to do, you just have to have a little mechanical aptitude. If he's intimidated by this type of thing, you can always get a used one. I think I could probably buy a whole van for $1200.
Repair Help & Product Troubleshooting for 2000 Plymouth Grand Voyager

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Distributor assembly/camshaft sensor for 2000 Grand Voyager


You can replace just the cam sensor, I've done it, but it's kind of a delicate job. You have take apart the distributor to do it, it's not hard to do, you just have to have a little mechanical aptitude. If he's intimidated by this type of thing, yo ... 2000 Plymouth Grand Voyager

My 96 grand voyager has a code p0340 where is the cam sensor located


... 1996 Plymouth Grand Voyager

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

1998 grand voyager speed sensor - 1998 Plymouth Grand Voyager


... 1998 Plymouth Grand Voyager

Input speed sensor for 1994 grand voyager - 1994 Plymouth Grand Voyager


... 1994 Plymouth Grand Voyager

I have a 95 jeep grand cherokee that will start,but idle is rough,wont accelerate.replaced brain,throttle position sensor,map sensor,idle sensor,coil,distributor,cap,rotor,plugs,wires,fuel filter.when i replaced the throttle position sensor it ran perfect until we shut it off.when we went to start again it went right back to the original problem.looking for an answer.thanks john


Check the fuel pressure on the fuel pump ... 1995 Jeep Grand Cherokee

94 Grand Cherokee wont crank. Checked voltage at crankshaft sensor plug and according to chilton it should be 8 volts. Camshaft sensor should also be 8. I have 12 at camshaft sensor and 0 at crankshaft sensor. Does this mean I have a bad PCM?


Did you measure the voltage while the black lead to the multimeter is connected to a known good ground? Is the key in the on position while you were doing the measurement? Remember that the PCM is a very reliable device, and only malfunction if abnor ... Jeep Grand Cherokee

My 96 grand voyager does not want to stay running and when i replace a sensor it wont run at all for a while? i have replaced the egr valve ,map sensor, idle air control valve, oxygen sensor, and the


Try crank sensor ... 1996 Plymouth Grand Voyager

Hello. my 4x4 1994 jeep grand cherokee with a 5.2 v8 stalls while driving and doesn't start. now it doesn't start at all, even after sitting for 2 days. i have read elsewhere that it could be the crankshaft sensor. it is throwing engine code 11 which is: No distributor reference signal detected during engine cranking. check the circuit between the distributor and the PCM. the guy at autozone swore up and down it was the distributor cap/and or wires and spark plugs. i am about 90 percent sure tha


Crank sensor is definitely on the bellhousing but most I've seen are on the drivers side at about 11 o'clock looking from the rear. regardless of exact position, it has to be in line with the flywheel. I suggest you do the continuity test at its harn ... 1994 Jeep Grand Cherokee

My 1993 v8 grand cherokee randomly dies after it warms up. any ideas? ive replaced the cam position sensor, crank position sensor, coolant temp sensor, distributor cap and rotor with no changes to the dying issue. the jeep has 188k miles on it.


Have the ECM checked. ... 1993 Jeep Grand Cherokee

Where is hatch sensor for 1998 Plymouth grand voyager (3.3 FLEX)?


Its built into the lock mechanism lock might have to be replaced try adjusting it first. should be able to move the latch. ... 1998 Plymouth Grand Voyager

Location of temperature sensor on 1998 Plymouth grand voyager


... 1998 Plymouth Grand Voyager

Chrysler Grand Voyager 1999 coolant temperature sensor part number please


... Chrysler Cars & Trucks

91 plymouth grand voyager dies when it warms up to operating temperature then starts and runs normally after cooling a little while. Replaced fuel filter and coil. Fuel still has pressure after it dies so fuel pump is working. This model has no pickup coil and ignition module appears to be in Engine control module. Is timing picked up by crackshaft sensor? What is the most likely culprit. Engine control module is $179.00 so would like to exhaust all other possibilties first. Coolant sensor must


Timing is picked up by camshaft sensor. If you don't have one then crank sensor. 02 sensor control air/fuel lean/rich mixtures. Plugged catalytic or muffler would cause this. Bad temps sensor will also cause this. ... 1991 Plymouth Grand Voyager

I have a 98 plymouth voyager se 3.3l auto (4 speed) and the speedo bounces cause the vehicle to have a jerking motion. when the speedo stays a 0 the vehicle runs fine but this doesn't last long befoer the speedo bounces. it also bounces when you are not moving the bouncing goes from 0 to 200 and when moving its between 20 and 80 . any help would be appreciated We have the same problem and had the speed sensor replaced three times. That was not the issue. Now when sitting at a stand still the sp


I would suggest taking it into a Jiffy Lube or Another Auto-Repair company. They can fix it for sure, and if they don't, you get a refund, and an apology. ... 2000 Plymouth Voyager

Well i have a 1996 grand voyager 3.0L v6 that when i start it aand driver it will go for a little bit then the engine will shut off and it will do this till its warmed up stop and go i hooked it up to an obd ll reader and it said throttle positioning sensor so i replased it and it still does the same thing what could it be im thinking the crankshaft sensor...


... 1996 Plymouth Grand Voyager

I have a 1998 jeep grand cherokee with a 4.0 engine. As I was driving, the engine died. I have replaced the spark plugs, distributor cap and rotor, crank sensor, cam sensor and coil. It will turn over, but ir won't start. There isn't spark at the plugs or coil. One more thing, it does get gas to the fuel rail.


You really should be using a good manual as a guide fro testing. For wiring diagrams chiltons is better than haynes. Have you checked power flow through the ASD relay?? ... 2000 Jeep Grand Cherokee

Where is the Manifold Intake Temperature sensor located in a 1999 Plymouth Grand Voyager SE? I did a Self Check and Diagnosis and DTC error codes showed up as 23, 55. 55 I am assuming is end of code list. So 23 shows up as Manifold Air Temperature Sensor. I need to find it to replace it and I can not locate it...


It is located in the air filter case in some cars is in the air duct that connects the air filter to the throttle body is a small sensor inserted in the duct with two cables connector . ... 1999 Plymouth Voyager

1997 Plymouth Grand Voyager - "Sensor" issues My van started dying at corners and running really rough. They are still running diagnostics but it sounds like at least part of the problem is the cam sensor. What should be the ballpark cost to have this fixed? Thank you!!


... 1997 Plymouth Grand Voyager

I have a 1996 plymouth grand voyager, I need to replace the camshaft position sensor but am unable to locate it. Where is the camshaft position sensor located??


... 1996 Plymouth Grand Voyager

I HAVE A 1995 JEEP GRAND CHEROKEE LAREDO 2WHEEL DRIVE, STRAIGHT 6 CYLINDER MOTOR. I INSTALLED A REBUILT HEAD RECENTLY.PRIOR TO THAT IT HAD LOW COMPRESSION IN CYL. # 3. IT HAS AN ACCELERATION PROBLEM. IF I STEP ON THE GAS QUICKLY,IT SPUTTERS & HAS NO POWER,ALSO THE TRANSMISSION SURGES. I TOOK IT TO A JEEP DEALER.THEY SAID IT NEEDED A DISTRIBUTOR,CAM POSITION SENSOR,OXYGEN SENSOR. I REPLACED ALL THESE.IT MADE NO DIFFERENCE!I SUSPECT IT MAY BE A TRANSMISSION PROBLEM,I UNHOOKED THE THROTTLE CABLE TH


Have you considered exhaust back pressure? ... 1995 Jeep Grand Cherokee

My 96 jeep grand cherokee keeps diying going down the road I changed the distributor cap, rotor, map sensor ignition coil, crank sensor, pick up valve,fuel filter, and air filter no luck please help


How is the idle? It never dies when let it idle for 30 minutes?\015\012Is it only dies when trying to accelerate? If this is the case then There are 3 things to check:\015\0121- O2 sensor.\015\0122- Fuel delivery rate is meeting spec at at fuel dist ... 1996 Jeep Grand Cherokee

1996 Grand Cherokee intermitant stalling . Occurs while stopped at a traffic light and sometimes while driving along. If moving fast enough it does recover and start running again. It also restarts ok after stalling at light. The fuel sytem has been professionally cleaned and gas filter replaced and the old filter was kind of sludgy. All 02 sensors. cam position sensor,starter, and battery have been replaced. It was suggested to me that the firing plate in distributor might be malfunctioning, or


I've tried all the above solutions and still experiencing the same problem. in doing some research it may be an electrical problem, the bolts holding the firewall may be grounding it before it should be and with expansion and contraction of metal in ... 1996 Jeep Grand Cherokee

I need to replace the crankshaft position sensor for a 1992 Grand Voyager. I can not locate the location of the sensor. Could anyone help? thanks


Try this pic ... Chrysler Voyager

Fitted a fixed towbar to my UK 2006 Grand Voyager (Diesel) and one parking sensor is picking it up so gives a constant beep when reversing - can i turn one sensor off (just unplugging it turns them all off!)?


... 2005 Chrysler Town & Country
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.7406 seconds