Having problems with your 2000 Mitsubishi Montero Sport ?

Rear brakes i have a mitsubishi montero sport 2000,after i remove the caliper i found i was stuck with two things,the first is the pins that hold the pads,and after the rotor refuse to come out,what i missing?lol,thx

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2000 Mitsubishi Montero Sport

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rear brakes i have a mitsubishi montero sport 2000,after i remove the caliper i found i was stuck with two things,the first is the pins that hold the pads,and after the rotor refuse to come out,what i missing?lol,thx


... 2000 Mitsubishi Montero Sport

There is a constant winding noise coming from the right front cv shaft, (sounding much like a helicopter rotor warm up) at first tried taking off the shaft to replace one of the boots, as it is completely torn, was not able to remove the roll pin, as i assume this is the part holding the shaft to the motor


Sounds like you have the problem figured out and I know exactly what you mean. Just takes paitience. Good luck and have a great day. ... 1996 Subaru Legacy

Rear rotors stuck on e brake shoes. Tried turning off, hammering off, loosing the e brake adjuster. The pins look broken holding the shoes on since the bottom part of the rotor pulls way out but can't get it off. the top part of the rotor the shoes start to come out. thanks mike


When i did my brakes on my 05 grand caravan i turned the parking brake adjuster and hammered like crazy till they came off then i replaced parking brake shoes and hardware they are never saved and after you have replaced that you need to adjust parki ... 2005 Dodge Grand Caravan

I Cannot get the rotor off the front of my 97 Accura2.2CL. I removed the four bolts holding the rotor to the hub, and the large nut holding the cv joint to the hub. The hub will still not come off so I can remove the rotor. Any ideas? Thanks


YOU NEED SOME WD-40 AND BIGGER HAMMER ... 1997 Acura CL

Steering wheel vibrates when i apply brakes. I have replaced rotors, calipers and breaks 3 times and the problem comes back after about 6 months or so. Any Ideas? Is this a flaw in design? are the breaks getting so hot that they are warping the rotors? I was told that when i come to a stop light i should not hold break on same spot ,That i should rolll a little bit so the break pad does not stay on same spot of rotor. that it can create a hot spot. Anyone ever heard of this ?


Had the same problem, took the roters in to get grinded and the problem went away. ... 2002 Dodge Intrepid

How do you get the right front rotor off of a 1996 plymouth voyager we have the tire off and the nut that holds the rotor on off but it wont come off we hit it thinking it might be rust holding it but


There may be small star washers on the studs holding the rotor on. You just need to pry them off. When the rotor is replaced the washers do not need to be replaced. They were only installed at the factory to hold the rotor in place until tires and ri ... 1996 Plymouth Voyager

2002 Chevy Cavalier(left light)! I know there is a clip somewhere on the headlight unit to take it out but where? I have taken off the slpash gaurd and the 2 bolts holding it in place so it wiggles but I can't get the heaqdlight to come out? The istructions I have for it are... ''you need to remove the plastic splash cover the extends the width of the car over the headlights by removing the plastics pins that hold it in . Pull up on the center of the pins to remove them. Once the cover is off, r


Dont these light have a splash guard on the inside of the engine compartment open your hood and usually theres a boot that covers the inside of your light take that off and youll see what your looking for sometimes you turn toggle counter clockwise a ... 2002 Chevrolet Cavalier Coupe

Hi: an oil leak at the front RS corner of the oil pan and front cover on a 1996 7.3L E350 powerstroke, requires the front cover to come off to get resealed, but something is holding it on at the bottom near the oil pan, rechecked for any bolts left and none found,is there something inside the pan holding it and does the pan need to come off first? thanx for any help.....geo.


I do not know what (or where) the front RS corner is. Is your leak in the oil pan gasket or in the front cover gasket.... This is just a guess... but I suspect that the front cover needs to be pulled UP not OUT.\015\012It seals around the crank ... 1997 Ford F250 SuperCab

On my 1999 oldsmobile alero. the overflow hose seem like it got a pin hold in it. because when i was driveing all this stam was comeing out. where is it comeing from?


Yes it could be a leak in the hose between the radiator and the overflow tank. The tank is supposed to hold excess coolant when the engine is hot and then release it back into the radiator when the engine is cool. ... 1999 Oldsmobile Alero

2004 Crown Vic- Headlights come on when first started and stay lit. Once driven 20 minutes and shut off; they may fail to come on or come on and then go out. Using the 'flash' wand, the high beams will light, but no responce to manual switch or normal highbeam switch. May come back on after holding the high beam wand or turning the headlight switch off and on.


There is a resistor in the light control module under the driver side of the dash. You can replace the whole module which is about 100+ dollars or if you're good with soldering, replace the resistor. You will need to remove the box and open it up. Fi ... 2004 Ford Crown Victoria

I am working on a 97 trooper with 4x4 and am doing the front brakes including the rotors. I am trying to remove the outer hub in order to get the rotor off and can not figure out what is necassary to get it removed. I have unbolted the 6 bolts that attach the outer hub to the rotor and have the cap and c ring off but there is some sort of a keeper that is split on top and bottom that is holding on a plate around the splined shaft. How does that come off Thank you -Barry


It's probably a nut that has slots milled on the outer diameter of it. You need a special socket that has tangs on it that will slip into those slots. You can probably rent one at your nearest Autozone. They usually make you leave a deposit for their ... Isuzu Trooper

I have been trying to get the rotor off the right front of my car I have the tire off and the nut holding the rotor on off the rotor will not come off we have hit it and nothing happens can you tell us what the problem is


Keep at it with rust penatrating oil and a brass hammmer it will break loose. Also try a propane torch and heat it. ... 1996 Plymouth Voyager

What holds the front rotors from coming off, while doing brake job.


Your brake calipers hold the rotor on, take off the two bolts that hold on the caliper. If you don't know what the caliper is follow the brake line .Where it ends is the caliper and it should be holding two brake pads. ... 2005 GMC Sierra

I have a 5 speed manual 96 honda civic and it refuses to go into first gear after I come to a full stop. If I go from reverse to first its fine but not if I am trying to downshift from any other gears


... Honda Cars & Trucks

Bmw stalling i have a 99 328i and it runs fine when u first start it and drives fine but after about three hours of constant driving it starts to lose power and if u come to a complete stop and then try to start off again it will stall then u have to hold it to the floor to get it to crank again ive changed the first o2 censor the one on the left side front of the motor if ur standing in front of the car lokking at it and the cam shaft position censor and cleaned the icv i took it to bmw and the


You need to replace brakes you are ruining the rotors.have fuel filter change.if stall out again have fuel pump pressure tested.because they are expensive dont buy one if you dont need it. ... 1999 BMW 328 Series

I'm working on a 2003 Buick Lesabre's rear brakes. It appears the bottom of the caliper is fastened with a 12mm bolt -- the top of the caliper doesn't seem to have a head to put a socket on or a torx head. I will be needing to put on new pads AND have the rotors ground, so the rotors will need to come off. The front brakes appear to be more normal with a larger pair of metric bolts holding the caliper on -- BUT the backs look forein to me.


The top of the caliper has a stud. Once you remove the lower caliper bolt, pull the spring-loaded upper portion of the caliper towards the inside of the car. It will come out and you have to pull the caliper off the stud. There is no upper mounting b ... 2003 Buick LeSabre

The spider gear pin in my rear end has come loose! i need to replace th rear end but dont wish to replace with th same year. i would like to go older since these rear ends have a bolt hold this pin in place verses this years pressed in type. what years can i do this with if any and what is the ratio?


Well i dont know if older rears would work due to design. but you could lock tite this pin on the same model year, make sure you get same gear ratio on the replacement axle. ... 2001 Ford Explorer Sport

Hi, I have a 2002 Yucon Xl and the parking brake pad needs to be replaced. Is the two callaper pins the only thing holding the brake assembly on the disc brake. If so do they come completely out of the pin holes ? Thanks Dave


Yes thats all that holds the caliper on and you can pull them all the way out, but if the bracket that holds the caliper wraps around the front then you will have to remove it also. two bolts. ... 2002 GMC Yukon XL

2000 landrover discovery abs tc and htc light came on had the brakes and rotors replaced and cleaned sensors. speedometer is working at first and then stops. brake light comes on and another light comes on. The codes where not cleared out? Is this causing the problem.


Hi I dont know weather this will couse the problem,but you should always clear the codes when you have done the work that the codes told you abaout in the first place.\012personaly I would get the codes cleard first before looking into the other ... 2006 Land Rover LR3

I have an oil leak in the front. It looks like it coming from a bolt that holds engine bracket. Also I have low oil pressure. The oil pressure goes up when I first start it then it go low very fast. I do not the front seal. Do any of the bolt come in contact where the oil flows in the engin??


HELLO. YES THE BOTTOM OF THE OIL PAN HAS BOLT'S THAT ARE UNDER THE FLY WHEEL.THAT'S WHERE THE FRONT SEAL IS.!! ONE MAYBE TWO THERE.!!! THEN THEY START TO GO ALONG THE SIDE'S OF THE OIL PAN ALL THE WAY TO THE BACK OF IT THEN THERE ARE MAYBE 4 THAT G ... Dodge Caravan

Hi, I have a 92' 626 auto. The gearbox clunks into first gear all the time when i accelerate from a standing start and the hold light flashes unless it is put in first gear prior to accelerating. I have been told to remove the battery terminal and place foot on the brakes for a miniute which fixes it for a while however it comes back. Plz Help. Steve.


... 1992 Mazda 626

I have a 1994 corvette coupe that i recently replaced plugs, wires, fuel pump, filter, cap and rotor. Recently I am experiencing hesitation, rough idle -loss of rpm at start up and for the first 10 minutes. Some times it floods out at starting and have to hold foot pedle all the way down to start. Car has 98,000 miles. Has original everything else. The idle will fluctuate in the first 5 minutes of driveing almost cutting out at times. I dont know if this is a bad fuel injector or something else?


SCAN CAR IT COULD BE FAULTY EGR VALVE OR IDLE SPEED TOO LOW.IGNITION TIMING OFF.FUEL INJECTORS DIRTY NEED CLEANING. ... 1994 Chevrolet Corvette

Jeep grand cherokee,i want to remove the rear axles.i have the rear cover off and i pulled the diff pin but i dont see any axle c-clips holding the axles in.also the axles dont push inwards towards the pinion to expose any locking mechanisms to hold them in.how do they come out?


The axles are bolted in. Rear drum brakes or disc? Remove the four nuts behind the brake and pull the axle. ... 1999 Jeep Grand Cherokee

I am changing the rotors on my 2002 chrysler caravan, the old rotors in the back wont come off. I think the emergency brake is holding it on


YOU HAVE TO REMOVE BRAKE CALIPERS MOUNTING BRACKETS FIRST BEFORE THE BRAKE ROTORS WILL COME OFF. ... Chrysler Town & Country

'96 Chevy Astro van -- check engine light comes on and car starts to hold back and shake. replaced crankshaft sensor, air flow sensor, did extensive tune-up -- everything new -- wires, plugs, cap, rotor etc. -- timing - cleaned out distributor --runs good for a while -- then, usually at stop light with car running and foot on brake, for no reason, it starts to hold back and act like it is going to shut down. Mechanics are stymied. They have done everything and cannot find the problem. HELP


... Chevrolet Astro
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.5445 seconds