Having problems with your 2000 Hyundai Elantra ?
My 2000 elantra gl has stopped firing on 2 and 3...what to do??
\015 Motor has missfired a couple of times over the past 2 weeks and this afternoon stopped firing on piston numbers 2 and 3\015
When was the last time it had a tune up? If you can't remember I would go ahead and change all your plugs to start.
Repair Help & Product Troubleshooting for 2000 Hyundai Elantra
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My 2000 elantra gl has stopped firing on 2 and 3...what to do??
When was the last time it had a tune up? If you can't remember I would go ahead and change all your plugs to start. ... 2000 Hyundai Elantra
My 1997 Jeep Larado had the distributor brake at the braket that holds it in place. The jeep stopped running of course. I went and got a new distributor and brought the number 1 cylender to TDC and put the timeing mark on 0. The jeep turns over smooth but will not fire, I have spark coming out of the distributor. What am I missing.
If the distrubutor is definatley installed correctly, as you have some one crank the engine turn the distributor sightly counert clock-wise and clock-wise until the engine fires up. Then set the timing with a light. Double check the wires are in the ... 1997 Jeep Grand Cherokee
I Have a 2000 gmc safari van 2wd The fuel pump stopped working so I replaced it. now cylinder 1 and 3 and not firing. So I looked at the plugs and they look good. I changed the wires but still no 1 and 3 firing. I get and p0135 error code (No 1 Ox sens) but that should not stop the plugs from firing. Could a vaccumm leak cause this or what? Thank you, Steven
The P0135 is indicating an O2 heater problem which is separate from your miss-fire problem.\015\012I would ask the obvious, are the #1 and 3 injector harnesses connected to the injectors? Have you check for a pulse at the suspect i ... 2000 GMC Safari
I have a 2000 Pontiac Bonneville 3.8 non supercharged. It is throwing the codes P0446, P0452, P0453. Yes it is throwing all of them and that is what is confusing me. Just reset the codes, did a start-stop-start-stop and got the 53 twice. Also, the fuel pressure isn't good, you hook up the gauge you get 0, when you turn the key on it jumps to 50 and as soon as the pump shuts off it goes back to 0, and when running it stays at about 47. I would greatly appreciate any help. and no my craftsman
... 2000 Pontiac Bonneville
91 Corvette - Service Engine lights, Speedometer goes (usually) to 0, Average miles per gal goes to 5Y5, engine stops. Engine cranks but will not start. Wait a bit, remove key, insert key and it will usually start. only code is 12 which is normal. (Speedometer sometimes goes to 108 or 17 instead of 0 - while sitting and Idleing) Can sometimes get out of engine stopping by flooring it - must be driving to do this.
... 1991 Chevrolet Corvette
Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil
Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus
My audi 100 wagon 1991 starts then stops immediatly.i have spark but the injectors fire only twice then stop firing
You need to reset the immobiliser,if you havnt got a book get back soon...... ... 1991 Audi 100
E36 convertible Hello i have problem with e36 convertible ,rear windows work fine ,but front works only at pulse, when button is pressed window star working for a short time 0,5 seconds and stop,when pressing the button again it continues for same short time 0,5 seconds and stops.
... Cars & Trucks
My 1996 saturn sl2 wont start. it is getting fuel up to the bleeder valve but wont start up. when i take the breather tube off and spray startign fluid in the throttle body it fires till it burns up the fluid. every now and then back firing. was running like a chamo changed the oil oil pan valve cover gasket and tried to fire it up and notta just keeps turning over. when i let it sit for a minute and try it acts like its going to fire then stops and just turns over. Timing? Air idle sensor? i ne
Did you check the injectors to see if they are firing? ... 1996 Saturn SL
My 94 Ranger 2.3L 4 cylinder would occasionally loose power when I was driving. Then it would start running fine again. It finally got a little worse, where I could stop when it was running rough so I could check it out. I put an inductive timing light on the plug wires. On the front coil 1 & 4 were firing while 2 & 3 weren't. On the back coil 2, 3, & 4 weren't firing. When it was running ok, all 4 were firing on the front coil, but on the back coil 3 & 4 still weren't firing. I'm not sure if th
If the hi-tension wires check out ok you may want to check on the distributor and the contacts at its end and in the inside. You may also want to test the ignition coil. ... 1994 Ford Ranger Supercab
I was driving into town, stopped at the stop sign at the end of my street, and when I hit the gas off the stop sign, the truck died. After 10 minutes or so of trying to start the truck, it fired up. Every time I tried to start, the engine turned over freely, and would sputter just enough for a shake. I drove for 3 miles with no problems, until it died again as I stopped at a stoplight. I had suspected the fuel filter from the beginning, so I went and bought a new fuel filter and swapped it out.
It still could be the fuel pump. Sometimes they don't just quit outright. Go to the vehicle. Reach through the open driver's side window. Turn the key forward to the run position. Listen toward the rear of the vehicle for the fuel pump to prime. ... 2003 Ford Expedition
03 gmc envoy with 5.3 140000 miles. Oil pressure reading fluxuates between 0 and 40. When problem first started pressure read 80. When vehicle was new it stayed at midpoint (40) vehicle has plenty of oil. if you rev engine or increase rpms it goes to 0 and stayes there. let off and it jumps around like it did when started (0 to 40). No engine pecks while running. Display indicates low oil pressure and stop engine. orange light (check gages) comes on when at 0. any ideas. Service engine has not c
There may be a loose wire or the gauge or sending unit may be going bad. The first thing I would do is to hook up a temporary oil pressure gauge, not using the old one at all. With this watch gauge while driving and see what readings you get. If the ... 2003 GMC Envoy Xl
Engine stops after starting the car and driving it for a few minutes, if I make a stop on a intersection his revolution will go to 0 and stop, then I have to started again and acelarate for it not to stop. What coul be the problem.
It can be the catalytic converter.clogged catalytic converter cause lost of power. that's why the RPM drop to 0.some experience backfire.it can be clean or replace. ... 2002 Mitsubishi Lancer
I have a 2ltre 2001 Bora which turns over when starting but won,t fire from cold start. However, when I managed to fire after the 9th attempt and gave it a run, then stopped and turned it over again, it fired first time and every subsequent turn during the first 1 hr.Once I left it standing all day and tried to start it from cold, same problem, it will not fire. Can you suggest possibe causes of fault.
Problem resolved. It was the coolant temperature sensor which had failed.\015\012\015\012joebrown123 ... 2004 Volkswagen Golf
Hi my car keep's blowing coils !! can't drive her for more than 5 miles then starts miss fireing and blow's the coil. starts up fire when cold but once gets warm stop's !! gone through
... Cars & Trucks
4g94 motor,in the morning when start the engine , i fond it up normal un stable like work with 2 spark plugs, start to move about 5 min. then stop the car after 20 min start the engine again after movin g the car and stop still the engine runing i heard lioke boming sound and alot of white smoking from the engine .when opened to see what happened in the engine i found afire under the engine after stopping fire one day later i start the engine the engine is normal, i would like to know what is th
... Cars & Trucks
Distributor problems?? I installed an accel distributor in my truck, found it was not compatible with computer for fuel injection. So, I went back to stock. I installed it found TDC aligned timing back to 0 noted the location of the distributor cap for number one firing position and connected wires in a clockwise fashion in the right firing order. Truck will not fire off now, I repeated the same steps three or more times, nothing. Any ideas?????
Are you certain you were on TDC of compression stroke? If you were on exhaust stroke, your dist. will be 180 degrees off.If timing is right, check for spark. You need to see a blue snapping spark at the end of the sparkplug wire to know ignitio ... 1989 Chevrolet Silverado 2500
Kubota ZG23 gas: After sitting all winter engine fired up immediately with a jump to the battery. Stopped and restarted several times in process of mowing with no problem. Three weeks later, when cranked it fired when first turned over but then nothing--would not run or even sound like it was firing. Fuse -OK Rplaced spark plugs. Checked fuel line. Everything looks ok--gas getting to the "bowl" on the carburetor. If I pour small amount of gas directly into the carburetor and then crank it,
... Cars & Trucks
I have a 1996 ford 350 van it has a 5.8 engine in it, My problem is when I start it ,It fires right up after a few cranks but if its in park it will idle high and then stall out or if it been running for a while it doesnt stall as much it will only stall than once I use brake or stop at stop light or stop sign I put plugs wires oil change distribtor cap kit on it and still got the problem the van is a 96 e350 5.8 engine any help b great thanks
Take it to AutoZone for a free diagnostic scan. Your local Ford dealer will charge you $100+ for the same scan. It sounds like the idle control valve and/or the mass air flow sensor. The scan will accurately pinpoint the proble ... 2002 Ford E350
What makes a 1998 ford expedition back fire and how can I fix the problem? It back fired on me when I came to a stop and now it is making this horrible back firing puttering soumd umder the hood and by the firewall
Any time a car back fires it can blow off vacuum lines. What a back fire is when the timing sequence is interrupted the spark plug on any given cylinder will ignite out of turn. If the exhaust valve is open at that time it goes out the exhaust. If th ... Cars & Trucks
First off when i am driveing down the road at a speed of about 30 then the speed gage drops all the way to 0 then it will go up and down back and forth the RPMs just go up and the truck wont grab or it just winds the engine rpms up and wont drive unless i stop and then start driveing easy and build up speed and ease into it then when i try to stop anytime dry weather wet weather it dosnt matter the ABS starts working and the light is on non stop it will go off every now and then i dont know if i
Your cable could be bad to your odom. ... 2002 Chevrolet Silverado 1500
Gages I have a 99 GMC Yukon and whenever I stop the check gages light comes. Whenever the oil gages goes down it comes on when I stop and whenever I take off it goes off. When I stop the oil gage goes close to 0 or the line it is on when the truck off.
Yoyu dont mention the mileage on your Yukon but low oil pressure will indeed light the CES light when it reachs o psi. Have you checked your oil? Have you changed your oil and filter. High mileage and poorly maintained motors will eventually wear out ... 1999 GMC Yukon
I have a 1996 Honda Accord with a non V-Tec 4 cylinder that stalls when I do a fast deceleration and come to a stop. I can cruise along, hit the brakes hard to come to a stop, as it comes to a complete stop, it sputters and shuts off. Then it is hard to start back up right away. The idle speed is where it's supposed to be. It almost feels like it maybe floods over somehow. I'm not sure. The fuel pump is new, new plugs and good fire on all of them. Any help would be greatly appreciated.
Check the power brake booster for holding a vacuum. It may have a small leak when the brakes are not applied and a larger leak when they are applied. Check the EGR valve for sticking open or for a leaky vacuum diaphragm. ... 1996 Honda Accord
2007 Elantra...This is my third winter with the car and I was always suspect about the abs braking. once the abs system kicks in ( grinding sounds as I apply the brakes on a snowy road) the car shows no intention of stopping...On several occasions I've rolled through stop signs. My only hope of stopping then is to pump the brake hoping that one of the times the abs doesn't kick or as in one instance, to prevent hitting a car in front of me, applying the hand brake. At first I thought it was jus
Have the dealer check it. you may need better winter tires. ... Hyundai Elantra
Today i found that the reason my car has been leaking oil is because my oil cap was gone!! the engine was dry this morning and clunking. I immediately parked it and added oil and a stabilizer. when i turned the car on it immediately stopped clunking but when moving from a completely stopped position it clunks some and then stops. Noticed it happens when I turn a corner too some. Any info would be greatly appreciated. I'm trying to prepare myself for the worst:0(
It sounds like you may have a spun main bearing. The only fix for this is generaly a new engine or long block. ... 1992 Mazda 626