Having problems with your 2000 Ford Expedition ?

Wher is yhe cam shaft sensor on a 2003 ford expedition

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2000 Ford Expedition

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wher is yhe cam shaft sensor on a 2003 ford expedition


... 2000 Ford Expedition

Where is cam shaft sensor on 2005 ford Expedition ?


... 2005 Ford Expedition

Where is cam shaft sensor on 2005 ford Expedition ?


... 2005 Ford Expedition

Cam shaft sensor on a 2003 ford expedition


... 2000 Ford Expedition

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

1998 ford ranger cam shaft sensor


There is a tool to line up the sensor while at top dead center on #1 cylinder you put it on top of the syncronizer fords name for the oil pump drive & interupter. good luck from schleck. ... 1998 Ford Ranger SuperCab

1996 ford thunderbird 3.8 cam shaft sensor location


Yes ... Ford Thunderbird

Idle issuse Im having issues with a 1995 ford explorer with the 4.0. The engine runs rough at an idle and does not have the proper power at speeds. I have replace the coil pack and have greater spark on cyl 1 3 5. With the old coil pack it had greater spark on cly 2 4 6. I have also changed the cam shaft sensor and the ecm. I run a code reader on it and it still points to the camshaft sensor.


You need to clear the codes from the ECM, and re-run diagnostic code. If you still have codes\015\012Check your grounds. If you still have power issues, re-check your wiring or firing order. If you have spark only on 2-4-6, where is your 1 - ... 1995 Ford Explorer

Code: P0340 Cam shaft position sensor "A" circuit 2004 Ford F150 5.4 2wd Engine light on, truck stalls when stopping or turning Replaced sensor myself, no change


Check your PCM GROUND, And Also Disconnect and Inspect ALL ENGINE Harness Connectors, FORD Has Had Many Problems Over RECENT Rears With FAULSE CODES Due to Poor GROUNDS @ ENGING/BODY/COMPONENT/ GROUND Locations, And ALSO HARNESS CONNECTORS with Poor ... Ford F-150

Change cam shaft sensor ford windstar 2002 - 2002 Ford Windstar Cargo


... 2002 Ford Windstar Cargo

2005 Ford Mustang GT with engine light on and the code showing is 340. Changed the cam sensor and the crank shaft sensor and the engine light is still coming on in the code reads the same what else could it be?


-After the problem fixed. you need to turn the light off by an OBD IIscanner.mai ... Cars & Trucks

1998 Ford Expedition will not shaft into drive when igination is in the start position, having to turn the key back into the accessory position in order to get the gear to go into drive, have replaced the neuraal sensor in the transmission, have checked the brake sensor all test indicated (ok).


There is a solenoid on the shifter that releases when in run position. if you are having to put in accessory to get in drive and start in neutral . then the ignition switch is bad. ... 1998 Ford Expedition

Location of the cam sensor 2005 expedition. - 2002 Ford Expedition


Its pointing in to the flywheel on the botom side of the engine block. ... 2002 Ford Expedition

I have a 2003 ford focus , I am having a misfiring problem. I have replaced spark plugs, wire, coil pack, air filter, fuel pressure sensor, replaced injectors 3 and 4 in which that the misfiring code. also replace cam shaft sensor. and still having the same misfiring code come up after reseting the check engine light . ANY SUGGESTIONS?


Check for Intake Manifold leaks with either a water mist from a spray bottle or Choke cleaner. Do this while the engine is running and you will know about a leak with an RPM change. I read about some intakes were 2 piece and the intermediate gasket ... 2000 Ford Focus

Cam sensor location on 2002 ford 5.4 - 2003 Ford Expedition


... 2003 Ford Expedition

2003 ford focus 2.3 engine cam shaft sensor location


... 2000 Ford Focus

Cant locate output shaft speed sensor on ford expedition


... 1998 Ford Explorer

How can I replace a cam shaft position sensor in a 2007 Ford Five Hundred


A check engine light or MIL Lamp, indicates a possible System Fault has occurredYou Check for CodesThe Codes direct you to a SystemYou then need Factory Diagnostic & Emission Manuals,so you can TEST Sensors or Wiri ... Ford Five Hundred

We have no check engine light & the ford minibus with the 6.0 diesel engine started running ruff at idle. Now it sputters running at high rpms and stalls at stop. We changed the cam shaft sensor but did not solve the problem.


Have you tried changing your fuel filters or using a diesel fuel injector cleaner. You could check your air filters also. It sound as though it is having trouble with fuel or air flow. If these both check out try your idle management control sensor Y ... 2007 Ford E-350 Super Duty Length XLT

We have a 1998 Ford Taurus that throws code P0340 every 2 days. We have replaced the cam and crank shaft sensors, the computer and the alternator. How can we fix this??


... 1998 Ford Taurus

How do you change the cam shaft sensors - 2004 Ford Focus


OperationThe CMP sensor provides\015\012camshaft position information which is used by the PCM for fuel\015\012synchronization. The CMP sensor detects the position of the camshaft.\015\012The CMP sensor identifies when piston No. 1 is on its c ... 2004 Ford Focus

Truck stalls replaced fuel filter,alternator,fuel pump,cam shaft sensors and vct selonoid on a 2004 ford f-150 supercrew. any suggestions?


Have you replace the crank sensor? or cranshaft sensor?\015\012if not do it, but before you do that make sure to have the truck inspect for a posible aftermarket alarm installed if it does have it remove and drive it for a few days,\015\0 ... 2004 Ford F150

WHERE IS THE CAM SENSOR LOCATED FOR A 1998 FORD EXPEDITION


... 1998 Ford Expedition

2004 F-450 7.3 L Super Duty won't start. Truck has been back to the Ford dealer 6 times. Cam Shaft Sensor has been changed 6 times. Most recently only 3 weeks ago. This morning - won't start. What's up?


Diesel isn't it, first thing to check is the glow plugs, one bad one will cause a no start, check them with a dvom, and check voltage going to each, other than that check pressure from the fule pump to injector pump ... 2002 Ford Super Duty F 450

2001 ford windstar code P0340 cam shaft sensor malfunction


You most likely have a 3.8 liter motor. You need to have a obd-2 diagnostic performed. Pep boys, Autozone, Aamco etc. can do this. (Ford also, but costly). If cam sensor failing, code will be stored in e.c.m, and data stream will prove out. The cam ... 2001 Ford Windstar
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.6834 seconds