Having problems with your 2000 Ford Expedition ?

Code 156 and 300

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2000 Ford Expedition

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

I HAVE A P0300 OBD CODE I DID A COMPRESSION TEST TO ENGINE AND IT PASS THE TEST,I DID CHECK EGR VALVE,CHANGE SPARK PLUGS,IGNITION WIRES, CAP AND ROTOR, I DID CHECK TPS SENSOR MAF SENSOR,FUEL PRESSURE,AND OXIGEN SENSORSI I FOUND THAT ON BANK 1 BOTH SENSORS (UP STREAM & DOWN STREAM )WORKS NORMALY BUT ON BANK 2 THE SENSOR 1 CHANGE FROM 0 TO 600 MILIVOLTS BUT NO CHANGES FROM RICH TO LEAN &SENSOR 2 HAS 0 MILIVOLTS & NO CHANGES FROM RICH TO LEAN SO I SWICHT SENSOR TO TEST THEM FROM BANK 2 TO BANK 1 AN


... 1997 Nissan Pathfinder

Using my OBD II on 2000 honda prelude trouble codes PO401 & (PO401 pd) all reads MIL on, monitors, 1 INC, EVAP, 7 ready, MISFIRE, FUEL, COMP, CATLYST, 02 sensor, 02 HTR, EGR. Will be cleaning out EGR, BUT do I need to replace my Solenoid? My prelude stalls and ideals out of first gear. (Autotranny). Is this stall caused by these trouble codes? Also with 1 pending code, what do you recomend? I ran car and used OBD II a 2nd time and only change was (0 inc) and 8 (ready).


... Cars & Trucks

How to enter code? went online and paid nine bucks, didn't really help me because of the following problem. 5 digit code, car radio has preset # 1,2,3,4,5,6.. one of my code is 0 and 9 how the hell am i suppose to enter it?


Come on here for free ,anyway you press preset 1 and use either the volume or tuning buttons ,maybe even the tape buttons to place the number then when all numbers press 6 to enter the code on the venerable old classic vehicle ... 1984 BMW 3 Series

Radio my code is 0319 How do you enter the 0 when it initially comes up to 1000 and there is no 0 on the first button, it goes from 1-9?


Using the station buttons , left to right , 1st button is 1000's, 2nd \015\012button 100's, 3rd is 10's, and 4th button 1's, push each button until desired\015\012number from each button , once you have the number in the display it\015\012should unlo ... 1993 Volkswagen Cabriolet

I have a 2002 galant gitting code 0340 camshaft sensor malfunction replaced but still getting same code what could it be? I'm getting fire on 3-4 but not 1-2 also noticed getting power to 2 coil pack but when I turn key to start power goes to 0


Coil pack has failed change it. ... 2000 Mitsubishi Galant

P171 code p171 lean to bank 1. 2003 Infiniti G35. Maf sensor seems to be within range. Only thing I noticed on my scanner is my long term fuel trim was 37.5% and 0 to 3%. Short term fuel trim was 99% and 0. I checked for vacuum leaks with no luck. I'm leaning towards bad O2 sensor or clogged/bad injector.


Yes i would say the same if you are sure there are no vacuum leaks ... Infiniti G35

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

Pliz help after taking my car for engine wash they used water to wash the engine and engine Codes came up . 16502 P0118 Engine coolant temperature circuit-G62:high . 16497 P0113 Intake air temperature sensor 1 circuit-G42:high. 16486 P0102 Mass air flow circuit -G7 0:low input. 16622 P0238 Turbo super charger boost sensor (A) circuit : high. 16955 P0571 Brake switch sporadic (A) circuit : malfunction. 18000 P1592 Altitude sensor /boost pressure sensor :implausible ratio. 16706 Engine RPM sens


Not Good: The Expensive main computer brain sustained a short from either the heat of the solutions or leakage allowing fluids to enter the components. If after a drying period this still occurs; then the computer brain needs replacing. ... 2005 Volkswagen Touran 1.6

I have a radio code 0421.. How do I get a 0 on the preset buttons (1-5)


Bottom 1 work for 1/2, then bottom 5 work for 9/0Test it and tell us news. ... 2001 Chrysler PT Cruiser

I have a 2001 Hyundai sonata. While driving home I started to lose power. I pulled over and the engine was running extremely rough like it was miss firing and halfway between the 0 and 1 on the rpms. Not sure if that is abnormal or not never payed much attention. Any ideas on what. Would be causing it. As of the moment it is not running. It turns over but does not start. And does anyone know if I can manually check the engine codes?


You can only check for codes with a code reader orProfessional Scan ToolAfter 30 years of these systems, it is had to believe peopleknow nothing,how is thatNormal,abnormal,don't pay attentionWhen I spend $40,000 fo ... Cars & Trucks

Ok ..what i have at this time is heavy misfires and i can get it to start hard sometimes and easy others ... start up you get a heavy fuel odor. probably flooding after it starts up and you can drive it. it with hesitate between 0-25 mph.and be missing real bad ..what i have is a code for misfire 1 for possible break in a vacuum hose. and the vap line for the canister.I have replaced the fuel filter only right now. no help tho.i have the 31 liter engine. I pulled plugs 2,4,6..6 looked nor


Sometimes you need the more powerfull spark plugs look the old ones and see if they math ... 1997 Chevrolet Lumina

01 accent gl 1.6 liter auto,air ;engine lite on,trouble code 342, (cmp, sen low) three wire sys. posit 1 tests bat volt. posit 2 is suppose to read 0-5 volts @700-3000 rpm;but reads 12.1 running and 11.3 koeo. posit 3 reads good ground as per spec. the #2 white- black ,when disc from ecm and tested for continuity shows 000.2 ohms (good)!no shorts to pwr or grnd. when re conn to ecm and this w/b wire cut aprox 3 in from ecm retested w koer i find that the sourse of the 12.1 volts is the ecm! here


P0342 is set when the ECM does NOT receive a signal from the CMP snsr. You may very well have GOOD continuity between the ECM and pin 2 (000.2 ohms), but that wire, if grounded someplace (shorted to ground or to another wire in the harness), the ECM ... 2001 Hyundai Accent

Does anyone know what the code 999 means on a 97 caravan? It also said chec 0, chec 1, chec 2, chec 3. Thanks


Don't know about 999 but the flashing light could be misfire, a clogged cat, cracked head. Take it and get the codes off of it. Last time I saw this on a dodge it was a cracked cylinder head#5 I believe. ... 1997 Dodge Caravan

Im buying a 1986 bmw 325e and it has a check engine light im familiar with locations and diagnostics of obd 1 and 2 vehicles but im not sure how and where to pull codes off of this vehicle is there a plug under the hood somewhere? and is the vehicle considered obd 0?


You can get hte codes from this BMW by turning the ignition key to the run position and then press the accelerator pedal to the floor 5 times, it will enter the diagnostic mode, count the flashes just like obd 1. Hope this helps, let me know ... 1986 BMW 3 Series

For my 2002 audi a4 quattro .0 litre I keep getting check engine light. The code is P0441 - Evapporative emission system incorrect purge flow. Also says warm up catalyst efficiency below threshold. Fuel system 1 cl Fuel system 2 cl calc load (5) 9.4 ect (5) 102 stft b1 1.6 What does all this mean. What is my problem. Thanks George


... Audi A4

Sat, sometime in January cel appeared Sun Engine steaming, upper hose clamp on engin was loose at engine connection cyl 1,3 side tightened clamp, washed away antifreze Mon read codes, engine misfire cyl 1,3 assumed something to do with antifreeze leak, cleared codes. 60 miles cel, same codes, replaced sparkplugs, swapped cyl 1,2 wires, cleared codes. 60 miles cel, replaced coil pack, air filter, ysed can of injector cleaner, cleared codes, 160 miles cel, used another can of injector cleaner. 160


I am sorry to tell you this but sure sounds like a head gasket getting weak. By year a model I am figuring you have a EJ-25 2.5 boxer motor. Not easy to really do plug test but are your plugs coming out with moisture on them? Check oil for water also ... 1998 Subaru Forester

But the check engine light came on yesterday. I checked the car using a OBD scanner, and it found 3 codes for the car: P0012- Camshaft position timing over retarded bank 1 P0301- Cylinder 1 misfire detected P0327 - Knock sensor 1 circuit low bank 1 or single sensor. After I checked the codes, (I did not erase any code) the check engine light went off . I do not notice any problem in the performance or running of the car and am generally not seeing any differences like fuel smells, lea


I think your idea is wrong. A fault code indicates a problem, though, cars can be used normally, but the problem is there, need to be addressed.or you can ask the 24 hrs live technical support http://www.diyobd2.fr/service/ , they will like to help y ... 2002 Mazda Miata

I know the code but the problem is the # 1 button on the radio is broken. every thing else on the radio worked fine untill I unhooked the battery now I cannot enter the code because you need the 1 through 4 buttons.is there a master code the button of course is stuck on 1 because of the 1000 that is displayed in the safe mode.any master code?


That is not good for you can not install the code. A replacement radio is what you need or get repairs made to the one you have ... 1998 Volkswagen Beetle

The check engine light came on yesterday on my 2002 Mazda Miata LS with about 140k miles on her. I checked the car using a OBD scanner, and it found 3 codes for the car: P0012- Camshaft position timing over retarded bank 1 P0301- Cylinder 1 misfire detected P0327 - Knock sensor 1 circuit low bank 1 or single sensor. After I checked the codes, (I did not erase any code) the check engine light went off . I do not notice any problem in the performance or running of the car and am general


... Mazda Cars & Trucks

2000 toyota 4 runner the code p1135 bank 1 sensor 1 (bad sensor). where is this sensor located and how many 02 sensor a 4 runner have. can i swap the bank 2 sensor 2 with bank 1 sensor 1 to see if the code will change. like the codes on p0302 and p0301.


P1135 Air/Fuel Sensor Heater Circuit Response (Bank 1 Sensor 1)\015\012almost certainly the heater inside the sensor has failed, the heater speeds up the time it take for the system to go into closed loop fuel control.\015\012The b ... Toyota 4Runner

Random misfire cylinder 1 code check. one spark plug wire #1 differant wire than rest hard one to get to. can't get #1 plug wire tight enough around think it is the wire, have new gas cap reset code stayed off for a while wire loosend up and check engine light came back on, thought i would replace all wires (Spark) code check it see if it runs better and reset code, you think?


Yes if it is loose can cause a misfire replace the wires as a set ... 1998 Chevrolet Cavalier

Codes i cleared all my codes and did a trip run and codes came back p0134 no activity bank 1 sensor 1,p0154 no activity bank 2 sensor 1,p0171 system too lean bank 1 and p0174 system too lean bank 2 all of them steady red.need my emissions done please help.02 sensors are new


Your sensors are reading correctly so leave them alone. What you have is a fuel delivery issue. Your MAF sensor is telling your engine to lean your fuel mixture. You need to remove and clean or replace (is better) the MAF. But first replace your PVC ... 2000 Dodge Intrepid

Actually I have 3 codes on my 1998 jeep grand cherokee 4.0 inline 6. (I scanned with my code scout code reader) They are: 1. code 171: System too lean - Bank 1. 2. code 320: Ign./Dist. Engine speed input circuit malfunction. 3. code 351: Ign. Coil A Pri./secondary circuit malfunction. Please help !!!


1. Check up the intake system for air leaks. Just spray carburretor cleaner product around intake manifold area, engine idling. If the engine rpm will raise up, there are air leaks. Replace intake manifold gasket, and test again the engine for air ... Jeep Grand Cherokee

Can anyone tell me what these engine fault codes refer to on a 1998 mercedes c180 auto,1.8 petrol. I suspect it may be releated to tempeture sensor. Total of 6 codes 065 (2,2,0,41) resistance too high 104 (2,2,0,68) resistance too low 122 (2,2,0,7a) resistance too low 126 (2,2,0,7e) resistance too low 129 (2,2,0,81) resistance too low thanks jim 161 (2,2,0,a1) resistance too high


Most common is o2 sensor ... 2002 Mercedes-Benz C-Class
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2141 seconds