Having problems with your 1999 Oldsmobile Alero ?

Which way are the threads for the harmonic balancer pully bolt run.

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Anti clockwise!
Repair Help & Product Troubleshooting for 1999 Oldsmobile Alero

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Which way are the threads for the harmonic balancer pully bolt run.


Anti clockwise! ... 1999 Oldsmobile Alero

Pulling harmonic balancer pulley from 300gt crank gear that runs timing belt wants to come off with it . I have removed center bolt but cannot get gear loose from pulley. It appears that the end of a pin or screw is visible going through the back pully and through the gear


The pin is normal, that is just for alignment. It will stay in the gear when you slide the pulley off.Spray the crank with penetrating oil where the pulley slides over it and let it sit a while.Take a hammer and lightly tap a ... 1992 Mitsubishi 3000GT

Which way do you turn the bolt on a 98 crown victoria harmonic balancer pully


To the left to loosen it and to the right to tighten it ... Ford Crown Victoria

There is a nut and stud that mounts the waterpump to the block.the harmonic ballancer pully on the crankshaft is in the way to removethe nuy off the stud. what is the process for removing the ballancer and is the bolt in the end of crankshaft right or lefthand thread


You will first have to remove the pulley from the crankshaft. The bolt in the crank is threaded reverse of the way the engine turns. In other words to loosen it you will need to back it off opposite the way the engine turns. If you can get on it w ... Chevrolet Silverado 3500

Ways remove harmonic balancer bolt


... Cars & Trucks

Have a water pump for a 318 i completely stuck,have removed all bolts ,also used threaded holes with screws that were removed,was messing up the threads when the screws got to the block,did not release the pump?Any help would be helpful,also tried a pully remover,no way to get it to budge because the pully remover could not get a bite. [email protected] Thank you!


Your gasket is probley stuck like glue. if your sure you have removed all bolts find something wooden like a 1 inch dowel or a 1x2 find an angle were you can get a bite on a corner or on the pump itself and gige it a good wack . this is a common prob ... BMW 318

How to remove the crankshaft harmonic balancer on a 1993 buick lesabre seems to have a large bolt holding it on. Is this a standard threaded bolt or reversed threaded?


National fine thread, regular right hand. You may need a puller to remove damper after removing bolt. ... 1993 Buick LeSabre

Harmonic balancer Dear Sir,Which way do i turn the bolt to get my harmonic balancer off my car. Thanks Wendell,


The bolt will turn left,counter clock wise to remove. ... 1991 Honda Accord

How do I replace the crankshaft position sensor on 1993 olds culass sierra with 3.3 engine. Do I need to remove the harmonic balancer? If so I cant find holes in the slots on the balancer to thread bolts into to pull balancer off


Here is a vedio how to change it.....www.youtube.com/watch?v=RuIislTGOwA ... Oldsmobile Cutlass Ciera

Harmonic balancer---i cannot get it off. it is threaded some unusual way?


... 1995 Honda Odyssey

What way do i turn the harmonic balance bolt to loosen it


... Saturn Cars & Trucks

I have a 1990 cutlass ciera and im in the process of replacing the timing chain and gear and was wondering if the bolt for the harmonic balancer is right or left handed thread. and what type of puller do i need to remove the balancer


Go to AUTO ZONE or call. they will tell you ... 1990 Oldsmobile Cutlass Ciera

Need specs on bolt through the harmonic balancer....which way do you turn too remove bolt ?


Normal thread,righty tighty,lefty loosey,an air impact would work great,hope this helps ... 2001 Ford Crown Victoria

Trying to remove harmonic balancer , i have the crank bolt removed and i have the puller they loaned me, but there are no threaded holes to screw bolts into


You may need a puller that does not use bolts but clamps instead ... 2003 Subaru Outback

96 plymouth voyager. PO113 code appears. Recent timing belt, power steering belt, and serpentine belt replaced. Harmonic balancer replaced along with idler pully were recent repairs. Car runs rough at idle. At driving rpm, the car runs good. Coming to a stop sign causes the idle to be low. Any suggestions is appreciated. I have a non interference engine. 2.4 dhoc


First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness conn ... Plymouth Voyager

How does the harmonic balance pully fit on a 1996 jeep cherokee is it bolted or pressed on as the pully is forward of the motor by 3/4 of the thickness


They are bolted on at a high torque. ... 1996 Jeep Cherokee

I have a 1992 saturn sc and I need to remove the harmonic balancer bolt and I can't get the bolt to turn, which way is it supposed to turn to come off.


I believe it is counterclockwise, check the manual on this site. ... 1992 Saturn SC

1988 Isuzu Pickup 2WD 2.6L Does the harmonic balancer bolt have regular threads or reverse threads? I can't get it to break free so I can change the timing belt.


They will be right hand threads ... 1988 Isuzu Pickup 2WD

I am trying to replace the harmonic balancer pully on a 1996 taurus lx with a 3.0 v6 i know the pully bolt is revers thead . I tried to loosen with an electric impact but would not budge what am i not doing.


Your impact gun may not be strong enough. Ive taken many off in the past and They are extremely tight. Juat keep working at it and i would recommend soaking it in WD-40 or some other kind of penetrating oil. ... 1996 Ford Taurus

I'M HAVING A HARD TIME REMOVING THE IDLER PULLY BOLT ON MY 1994 CHEVY LUMINA SUBURBAN WITH A 3800 ENGINE. WHICH WAY DO THE THREADS ON IT LOOSEN; COUNTERCLOCKWISE, OR IS IT A REVERSE THREAD? CAN'T SEEM TO EVEN START TO LOOSEN IT. THANKS A LOT; FRANK MAZZA N.Y.C.


Couter clock wise! some times you might have to aply heat to get them to free up. ... 1994 Chevrolet Lumina APV

Need to know if bolt for harmonic balancer on a 2002 buick rondezvous is right hand thread or left hand thread


It is a standard 'right-hand thread' and turns counterclockwise to loosen. Best to use a high quality impact wrench capable of 350+ ft lbs of torque. ... Buick Riviera

I want to remove old water pump on 96 Park ave. and have all bolts out except 1. Its a long bolt and a pulley is in the way. How do I remove that pulley/ I have the right fitting, but I cant seem to brake it loose. Is it reverse threads?(Its the farthest pully to the rear of the engine at the bottom)Can you offer any suggestion?


Your car has 3.8L engine (3800) good engine, if your talking about the bolt all the way to the left end of the water pump, you will need a power steering pulley tool, autozone rents these tools for a small deposit which they will return or what you c ... 1996 Buick Park Avenue

Trying to change the timing belt on a 2003 Hyundai Accent and can not get the harmonic balancer bolt off because the pully keeps turning. Is there a special tool to hold the pulley so I can remove the bolt?


You can put a breaker bar and socket on the bolt and unplug a) the injectors or b) the coils so it wont start and crank it over like 2 times put the breaker bar on the pulley with the handle of the breaker bar touching the ground and u crank it and i ... 2003 Hyundai Accent

Harmonic balancer retaining bolt is off, but i can only get two of the three puller bolts to thread. How do i remove it?


RETAP THIRD HOLE ONE SIZE UP ARE IF IT IS SAE THEN USE METRIC I HAVE WENT COURSE THREADED BOLT ALITTLE BIGGER JUST SO IT GETS A BITE. ... 2000 Pontiac Grand Prix

Crank harmonic balancer bolt thread


... 1994 Honda Accord
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.1798 seconds