Having problems with your 1999 Nissan Maxima ?

Hi Dear, I having trouble puting my CAMs shafts back @ TDC position, anything would help,photo, diagram..... Thank you,

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Well its bedtime in this time zone so if you dont get a reply then answer this post and tomorrow after work i will explain how to do it with no timing marks .Do not play with it in case you bend the valves
Repair Help & Product Troubleshooting for 1999 Nissan Maxima

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi Dear, I having trouble puting my CAMs shafts back @ TDC position, anything would help,photo, diagram..... Thank you,


Well its bedtime in this time zone so if you dont get a reply then answer this post and tomorrow after work i will explain how to do it with no timing marks .Do not play with it in case you bend the valves ... 1999 Nissan Maxima

1998 Jeep cherokee just shuddered and died when i was backing out. Possible crankshaft positioning sensor or fuel pump?? For the past week it would give me troubles starting it. It would shudder and turn over and when it first started i would give it gas until it was warmed up.


You need to check to things out,first is fuel pressure at thr fuel rail reed valve,you need at least 50psi for the injectors.second have someone check the engine temp switch,to see what temp it is telling the computer your engine is. ... 1998 Jeep Cherokee

Ok, so my 2003 ford escape will not move in any gear. i have had no trouble out of it until now. it has 99000 miles on it. i got out of it and then back in 10 minutes later without cutting it off and it would do anything. we were jumping another car off and would like to know it this could have done something to it. i have replaced the TSS sensor and the OSS sensor with no avail. no fuses are bad and ATF looks good. what could this be? my check engine light is not on and never has been so it giv


Hi,\015\012 I don't know if the trannie a standard or automatic but my first suspicion would be the linkage to the trannie shift lever. Possibly it has become disconnected or broken... just a thought.\015\012Hope this helps... Good luck! ... 2003 Ford Escape

Starting problem i installed another engine in my 1996 chevy tahoe (5.7liter) iwas having trouble starting it ,it would only turn but would start so i put the #1 piston back up to TDC the i pulled the distributor and installed it with the rotor pointing to the #1plug wire at the distributor .now it will start and cut right off even if i hold the gas and strat it up it cuts right out. do you have a clue of whats going ?


Do you have a security light flashing? Sound like a theft system problem. Some 1996 Tahoes had passlock. ... 1996 Chevrolet Tahoe

I have a 2001 Prius. The ignition will not turn over. I was told there was a problem possibly with the relay a few months back. The engine would have a misfire for the first 20 seconds after being turned on, eventually driving fine after that. Now it will not start, first it was making a loud noise in the black box that says relay on it when the key was put in the "on" position, now it will not do anything. Please help!


... 2001 Toyota Prius

Hi there, I am having some trouble with my Cadillac Eldorado 1998 ESC. My air conditioning recently stopped working, says low on refrigerant. I added some freon recently with no affect. My vents would still blow warm air though. A week ago while I was driving alond I smelled a burnt plastic smell then I seen white smoke come out of my middle vent!? I immediately stopped and opened the hood to find nothing out of the ordinary. Started back up and didin't notice anything different until I tried to


Sounds like the blower motor has burned out, also u can't just add refrigerant u must know what pressure at the low side charging port indicates the system is charged, if that pressure doesn't go to about 30 PSI then u will have no cold air, please g ... 1998 Cadillac Eldorado

Infiniti I35 2004 with all options and 80,000 miles. The driver's electric seat is jammed at the back position and tries to go forward whenever the car starts and all it can do is make a grinding sound and slightly twist towards to the left. I used a mirror and flashlight and could see nothing under the seat that could be jamming anything. Is it most likely the gears is stripped? What would it cost to repair in Las Vegas? It is possible to repair by a non-expert owner?


Sounds like the motor is bad easiest and cheapest way to fix would be to get a complete seat from the Junk yard the seat should come with all the motors and tracks all you have to do is unbolt old seat and bolt down new one only draw back to this i ... Infiniti I35

Hi there, I am having some trouble with my Cadillac Eldorado 1998 ESC. My air conditioning recently stopped working, says low on refrigerant. I added some freon recently with no affect. My vents would still blow warm air though. A week ago while I was driving alond I smelled a burnt plastic smell then I seen white smoke come out of my middle vent!? I immediately stopped and opened the hood to find nothing out of the ordinary. Started back up and didin't notice anything different until I tried to


You probley have a blown fuse most of those usually ties together in the fuse box. ... 1998 Cadillac Eldorado

I have a Ford F250 XL- While plowing today I notice that the truck was swaying to the left but didn't think anything of it, thought it was the wet snow. Then while back blading some snow, I noticed that the truck would not back up, almost like I didn't have any 4 wheel drive. I would lift the blade and the truck would back up. When I put the blade down and pushed the snow it would move, but I still felt like the truck had no tracktion on the front drivers side. Almost like the front drivers side


Check both front lockouts,1 side or the other could have broken,unlock 1 side and reach underneath and try turning the axel on the other side-----if it turns all the way around, then replace that lockout,if it doesnt turrn then try unlocking that si ... 1998 Ford F250 SuperCab

Idle problem As of couple of days ago my car was fine. I installed a fender and door the car was fine. So I drove it(couple days later) and noticed when I came to a stop the idle would surge up and down. then it would shut off. Starts right back up and no trouble when running. Its a 91 Grand prix se with the 3.1 V6.As of today I drove it about 70 miles and no trouble till I come to a stop then it would surge and almost shut off till I bump the throttle then it would be fine going again.Sometimes


I found the problem dirty throttle body. Thanks though... ... 1991 Pontiac Grand Prix

I replaced the engine in my 2000 dodge intrepid 2.7 engine. Would not start with my cam position sensor connected. I unhooked the cam position sensor and the car started put ran at 2500 RPM. Replaced cam position sensor. The car still would not start until I unhook the cam position sensor.Is their anything else I can check?


You need to verify the magnet in the engine is stll intact. Also you need to graph the sensor for a steady pulse. Search how to test a Cam and Crank sensor.. Also you should have a code stored for the no start condition. This will tell you what se ... Dodge Intrepid

Van died after starting. check for spark, yes, changed fuel pump relay and fuel pump still will not start. before this happened the dash gauges would go dead. hit the dash they would come back on some times. would come back on their own other times. does this have anything to the problem ?


Instructions\012\011\011\011\012\011\011\011\012\011\011\011\012\011\011\011\011\012\012\011\011\011\011\011\012Things You'll Need:\012\011\011\011\011\011\012\012\012\011\011\011\011\011\011\011\011 ... 1998 Plymouth Voyager

Vehicle trouble 2000 jimmy gmc while driving home the 2 back wheels seized up and would not move. Had to get towed. Just prior to this happening noise from back end,it would go into gear but would not move due to wheels seized.No warning prior other than noise moments before . When unloading from the tow truck brakes felt down. Any idea as to what could be wrong?


I think you may have a blown Rear Drive Axle due to lack of lubrication. It will be hit or miss if the housing is still usable. I would be against the problem being brakes as the likely hood of both wheels failing at once is extremely unlikely. ... 2000 GMC Jimmy

My 1996 E250 4.9 Ltr 3/4 ton van 6cyl was giving trouble restarting after it run for a while. You have to wait until it cool off and it would start right back up. It would do this each time you shut it off. I change the pick up coil in the distributor and put it back together and it started right up. I run iot for a while until it reach operating temp and shut it off and could not restart it again it just cranks but would not start. Could this be a bad coil? I think this van carries the TFI-IV


Hi,\015\012\015\012 Run these tests after the Van Won't Start After its Been Driven .and up to Operating Temp.\015\012\015\012Check to see if your getting Spark to your Plugs,After it wont start. Then Check to see if your Gett ... Ford E-250

I have a 2001 Lincoln Navigaor that i just had the electronics module replaced 5 days ago my check suspension light would also come on and sometimes would stay on until we would turn the truck off and restart it then it wouldn't come back on for a while but now my rear is really really low and now u don't even hear the noise that it would make when we would put the key in the ignition in the start position which is the same noise it would make whe we would turn the vehicle off also the check su


Hello, this is a really nice vehicle until something breaks. The Air ride system is complicated. I do think you have lost a ground wire in the rear area of the truck. Your fuelgauge problem and your Air ride problem may share the same ground wire. ... 2001 Lincoln Navigator

I have a 2001 chevy astro van, V6. Past few mornings its been around 40 degrees, having trouble starting and I will drive for the next 20 to 30 mins, make a stop and get back in to start and still a bit rough. I would hear some clicking sounds and the clock/radio would say ERR, try again and it will turn over. I recently had a back tail/blinker light out, changed the blub and worked for a few mins then go out again, checked the connection and it seems to be the wiring. I moved it and taped t


Welcome to FIxYa.com\015\012\015\012 \015\012Ok this is a two part question. First off go to auto zone and have the alternator -starter check . It is a free service . I need to know if the alternator is ... 2001 Chevrolet Astro

Rear brake replacement needed but not to the front first? At 92k miles and never any brakes service. Just wondering why the back would go bad first. they are saying to take all apart and clean the front but replace the back. Would the front be going bad soon and wouldnt be the money to do anything to the front?


Yes you are right but maybe you use the hand brake most of the time or the rear brake was tight but you never noticed ... 2007 Toyota Camry

I drive a 2004 Pontiac Grand am GT. Today after I had to accelerator really quickly, my car started to mess up. I would hit the gas and my RPMS would go up an then fall right back down like the car was shuttering back and forth. I parked my car after that, a few minutes later I left and turned onto a street. At that point, my whole car turns off. I have no power steering or anything. I try to start my car and nothing happened. The more I try to start it the more it starts to turn over and in les


It sounds like your fuel filter is getting clogged. There is enough flow to allow the engine to run at low load, but as soon as you try to dump lots of fuel into the engine, there is not enough flow, and the engine dies. Replace the fuel filter. ... 2004 Pontiac Grand Am

I'm helping out a friend on a 1996 Camaro and the problem I'm having is when I try to start the car everything turns on lights, dash etc... but when I turn it all the way forward to the start position nothing happens it all goes Blank, the power go out and thier seems to be no power to anything until I put it back to the on position then the lights, radio, power etc... come back on. Can you help? Thank you, Tim


Check the connections to the battery,and remove the cables from the battery,negative first,and clean the battery terminals on the battery,and the cable ends,until shiny,then try and start the car,have the battery checked,and once the car is started h ... Chevrolet Camaro

On vacation, we went over the Continental divide or four times. The vehicle had trouble getting over the divide. When we got ready to go back home we stopped to eat lunch turn the vehicle off. Went back out and it would not start. I mean, it would start, but it was shut off after 20 seconds. Then the next day, we drove the vehicle's 750 miles with no problems at all


Souds like it could be a vapor lock problem. As long as the engine is running, cool gasoline is moving through the fuel system. Once the engine is shut off, if the fuel line at some place is getting hot it can cause the engine to not start or quit ... 1997 Dodge Grand Caravan

I have a 2000 VW Passat and last week I had to remove the driver's side door panel and replace the side mirror controller (this is the controller that moves and defrosts the mirrors). Thus far I had no troubles, the panel came off without any trouble, the controller unplugged and plugged in with ease. Before I put the door panel back on I checked the mirrors to make sure they both moved. After everything checked out, I put my door panel back on, only to find out that the door handle opener would


You either bent the door rod or the rod came off ... Volkswagen Passat

When putting the back seat upright from a fold position, the seatbelt would not release tension, and kept getting tighter. Now the back seat will not return to the proper position, and the seat belt will not loosen.


MIGHT HAVE TO REMOVE THE SEAT BELT TO HELP RELEASE THE TENSION AND RECONNECT IT BACK. ... 2000 Volvo V70

I have an 04 GMC Envoy XUV. I went to lock my vehicle and accidently pushed the window button on the remote. The rear window went down and I tried to put it back up with the key but it would not go up. I tried to open the back gate and it would not open either way(swing open or drop down) The see manual for rear window came up on the DIC and I did what the manual said but nothing happened. I then tried to open the roof with no luck. So now my rear window is stuck in the down position, the


The most common issue with strange acting or random function of a remote, IS THE BATTERY. Replace the battery in the remote before forcing anything or taking things apart. Good Luck! ... 2004 GMC Envoy

Electric front seat stuck in forward position. It's a 2002 Camry. I moved the electric adjustment completely forward looking for an item and it would not return back to the original position. Both tilts work but not the back button.


I had the same problem on my 2003 Toyota Camry. The threaded drive screws are what spin underneath the seat and cause the seat to move back and forth (same way a garage door opens or closes). When the seat gets all the way in the forward position, t ... 2003 Toyota Camry

Trouble codes my 1988 Honda civic 1.5l starts up fine for a few seconds and then idles up and down like the engine surges.i read about how to read trouble codes and mine flashes real quick once and then a pause then flashes 6 times real fast and then starts all over .if i understand it right its giving me a code 7 which is the throttle position sensor if this is correct would this cause the engine to idle up and down any help would be nice thanks rob


Yeah i do have the same problem..........before. Yes its that throttle nagle sensor. you have to replace the whole throlle body cause the sensor is not a bolt on part.....goodluck! ... 1988 Honda Civic 2 Door
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.9051 seconds