Having problems with your 1999 Nissan Maxima ?

Computer is sending a knock sensor problem code, where this sensor is located? nissan maxima se 1999

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

The knock sensor is located below the intake manifold
Repair Help & Product Troubleshooting for 1999 Nissan Maxima

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Computer is sending a knock sensor problem code, where this sensor is located? nissan maxima se 1999


The knock sensor is located below the intake manifold ... 1999 Nissan Maxima

Hi I have a 2003 Nissan Exterra SE, . I went to auto zone and got a diognostic test done and the codes came back as the upper passenger oxy sensor a the knock sensor. to replace the oxy sensor isn't a problem . but how and where is the knock sensor located...


The knock sensor is on the back side of the engine bolted onto the block. It looks like this\015\012 ... 2002 Nissan Xterra

The truck broke down and cut te power send it to shop to fix it the mechanic replace the distributor and whe i pick it up from the shop iddle was from 500 to 750 i was running good then 2 day after i was on the freeway and rpm start to go down from 4 to 2 and back to 4 the cut off and after a towing the truck start i drive in the city with no problems just the iddle up and don it turns of but starts i believe it may be knock sensor or computer but i dont know where is located knock sensor or com


Replace your fuel pump ... GMC Sonoma

I have a engine light on and the code is P446. This is after I changed the three 02 sensors and the knock sensor. Now the P446 problem code evap control valve. Should this be replaced or should I be looking in a different area. 1996 Nissan Maxima


Being a 1996 it is likely it does need replacement ... 1996 Nissan Maxima

I have a 2002 Nissan Maxima and the check engine light has come on. One of the codes being reported is P0021. It seems to be related to a cam position sensor. Does anyone know the location of the sensor? And if the problem is just the sensor?


Here is the location....http://www.courtesyparts.com/maxima-parts-a33b-2000-2003/genuine-nissan-parts/engine-electrical/221-distributor/-c-1956_1957_1988_1990.html ... 2002 Nissan Maxima

2000 Nissan Xterra, throwing codes, PO340 Camshaft Position sensor malfunction, PO325 Knock Sensor malfunction, PO 731 Gear 1 incorrect ratio, PO 1336 unk as my book for the reader doesn't list it. Do I need to change a computer, or sensor? The engine runs till you accelerate then it starts running really rough, then shuts off. Does anyone have any ideas on how to fix this problem?


... 2000 Nissan Xterra

I recently changed the transmission in my 1996 Nissan Maxima and since that time it has been hard to start. I have plenty of battery but it seems to bog some times when it is cranking. I have added a ground cable directly to the starter mounting bolt thinking I had a bad ground problem. This did not help. Could it be a coincidence that the starter is bad. It almost seems that it has a timing issue. Is there a sensor that controls this. The codes are PO325, knock sensor failure and PO440, evap l


You need to remove the trans and clean up the bell housing and trans housing. If you got this tranny from a junkyard chances are its been sitting around and has some surface corrosion on it that needs to be cleaned off. If you do this you should be ... Nissan Maxima

1995 Nissan Maxima. Check Engine light comes on. Code 34. Knock sensor. Replaced sensor. Same problem with engine light


Hello there:on these types of lights what is needed to be done is after the repairs are made the vehicle needs to be taken to a Kragen or a Autozone so they can hook up the FREE DIAGNOSTIC CENTER AND CLEAR THE CODE otherewise this wi ... Nissan Maxima

I am looking for a diagram for the knock sensor on a chevrolet 2000 silverado v.8 and its 2 wheel drive.We need the location of the knock sensor. Is it under the block or is it on the passenger side or driver side. Please help us with this problem and please send a diagram along with the location of the knock sensor in case its hard to see diagram. Thanks for your time!!


I just replaced both knock sensors on my 2001 5.3 gmc slt. They are located under the intake manifoild. ... 2000 Chevrolet Silverado 1500

1996 Nissan Maxima 2.5 V6 Engine Knock sensor The engine runs fine; but it sets off 2 codes knock sensor & ignition. Just this week had the plug wire and knock sensor changed, new. Still the same code light comes on. I appreciate any and all help thanks.


The knock sensor is a major pain in the a..s to change I would suggest taking it to a reputable shop for a second opinion to see if they realy performed the work. Also with OBD11 (2) diagnostics if you have multiple misfires its not the wires its som ... 1996 Nissan Maxima

2004 Nissan Frontier pickup crew cab 4x4, Where is the knock sensor location? it gives me code P0328 knock sensor B2? where is the knock sensor located at?


... 2004 Nissan Frontier

I have a 96 Nissan Altima that randomly stalls out while driving...the car is giving mixed readings and the Midas said they know there is problem but having trouble determining which one it actually is....the first time scanned it came up with both cam sensor and crank sensor....they cleared codes and drove until light came back on and this time read knock sensor....codes were cleared again and now reading exhaust gas thing? What is real problem before I throw $ into something it's not


... 2005 Nissan Altima

I have a 95 nissan maxima and I am trying to locate the computer. I found a connection that looks to be for obd2 near the passanger side of the car in the center console. did they make obd2 on 95 maxima's? if not where is my computer located so I can run my codes? thanks in advance.


Jnuttz99: The ECM is located to where you access it on the passenger's side of the car. You remove the center console cover under cover, remove the harness protector and them you can remove the ECM.\015\012The car is O ... 1995 Nissan Maxima

Engine misfire and knock sensor bank 1 codes on 1999 Nissan frontier 3.3 v6


I would want to see the actual codes, but if it is one or two cylinders you could have a failing injector and it not show up as a trouble code.If one of the injectors is failing it can have a high resistance and affect the other injectors in that ... 1999 Nissan Frontier

Have 2001 nissan maxima with surging idle when in park or drive,but a stop. idle air control check, is ok; oxygen sensor replaced, but didn't solve the problem. Nissan dealer stated they checked everything. But it is the motor mounts that are bad, which caused the computer to malfunction. The check engine light comes on at times and stays on for days, then goes out. They (nissan dealer) checked everything, but the mounts are the problems. Any suggestions. Nissan is not standing behind their


I doubt mounts would cause surge. It could be throttle position sensor, camshaft position sensor or Map sensor. It would be good to have a non dealer shop put a computer on it and test it. Otherwise you can remove the sensor and use an ohmeter to mak ... Nissan Maxima

Can a bad map sensor cause a 2002 nissan maxima to have problems going above 2000 rpmscar runs has engine code for bad map sensor but will not go over 2000-2200 rpms so you canot really accelerate normally or go above 60 mph. Could the map sensor alone cause this problem or would it be more likely that other issues are present


If the sensor is bad it causes the computer to change air/fuel mixture for the fuel injection and would have that effect,other possible causes would be a clogged fuel filter or the fuel pump is going bad but you need to change the map sensor if it is ... 2002 Nissan Maxima

Where is knock sensor located on a 1999 nissan maxima


Under intake ... 1996 Nissan Maxima

The check engine light came on in my 1995 Nissan XE 4 cyl pickup and I took it to the shop. They said it was the O2 sensor & Wanted 385.00 to replace it. I went to autozone and got one for 20.00. Also replaced the plugs and plug wires. Disconnected the battery cables to reset light but it came back on. 1. What would be the next step now that the O2 sensor has been replaced? 2. Where is the computer located to see what codes come up now? 3. What are the codes for the 1995 pickup?


I would recommend you have Autozone lookup the code on your vehicle, and then report back here with the code. Here is a list of the Generic Codes: http://www.obd-codes. ... 1995 Nissan Pickup

Problems? For the last 3 years it was like Newton's Law. Anything that could go wrong did. The computer in these vehicles are ****. Every little touch sends the sensors off. I've had the dealership look at my Service Engine Soon light 3 years ago and they couldn't "FIGURE OUT" how to fix it. I've gotten everything fixed that has needed to be, but it's been dinging for 3 years. 3 YEARS. No one can find the code to reset the computer. They drive great, but have a lot of problems. Now I have the Se


First off your air filter has absolutely nothing to do with you traction light. If the car is not giving you a fix me code, then it may be as simple as turn the key on but don't start it, pump the gas 3 times then turn the key off. wait a minute or s ... 2001 Pontiac Aztek

Hello Hi, my 2003 nissan sentra just died while I was driving it and it has the p0335 code, I had a fuel pump/sensor error code for awhile and ignored it :( now this happens. do you think my problem could be related to the fuel pump/sensor and crank angle sensor, or just the sensor. And could you tell me where on my car thats located? Thank You!!!


After the new sensors are installed and the code still comes back, replace the timing chain. They have been known to stretch and cause the P0335 code on these engines. ... 2003 Nissan Sentra

Jeep keeps stalling along with engine knocks, hesitation at times. was told the computer is bad because codes can't be read. 165,367 miles on it, nobody knows why it stalls because of no codes. other than that, what else would be the problem, too much money for me so far new pulley,battery,tune up,fuel sensor, a/c charge...i know maintaince is normal but i need a surpentine belt,tires, & now computer..i've only had this for 7 monthes & this has hit me all at once


Try your e.g.r. valve,pcv,and a couple of bottles of fuel additive and a new air breather system. ... 1997 Jeep Grand Cherokee

Knock sensor located on nissan maxima


... Cars & Trucks

My 2004 Nissan Xterra was running well w knock sensor code. Had it replaced and now in the morning it starts and sometimes stalls. Comes up w the code for the IAC. Tried to reset code and doesn't go away at all like the other code did. Trying to locate the IAC w no luck. Is there a picture of one in the engine I could look at?


... 2004 Nissan XTerra

1999 Pontiac Grand Am is setting knock sensor code...knock sensor replaced... reset computer ....knock sensor code back. car has 120k so I replaced for and aft O2 sensors ....and the coil pack ......knock sensor code returns immediately. It is currently running in safe mode . It's a four banger......where do I go next? Ran the car with two different scan tools ...same code ...knock sensor...thanks !


Check all ground wires to these sensors. Even corrosion will cause codes to pop up ... 1999 Pontiac Grand Am GT

96 Nissan Maxima continues to have engine light come on with trouble code of P0505. List of things we have done already to try and fix the problem: 1. replaced throttle position sensor 2. clenaed throttle body with throttle body cleaner from Nissan and replaced gasket 3. cleaned IACV with throttle body cleaner from Nissan and replaced gasket 4. replaced Mass Air Flow Meter 5. Replaced Spark Plugs


I had a similar problem - took it into 'Nissan Professionals' and they changed everything you did as well, and had no luck. After 4 or 5 times working on it, they told me that it was a 'loose wire' that had to be re-soddered and then the problem was ... 1996 Nissan Maxima
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.3189 seconds