Having problems with your 1999 Mitsubishi Galant ?

Am an elctriacian in kenya nairobi where can get the information on how to repair the gdi high pressure pump and how to get the mitsubishi canter flash codes

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1999 Mitsubishi Galant

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Am an elctriacian in kenya nairobi where can get the information on how to repair the gdi high pressure pump and how to get the mitsubishi canter flash codes

... 1999 Mitsubishi Galant

Fuel Problems I just purchased an 89 Ford F150 with a 302 and it will not start without ether or gas but once it starts it runs on its on and at idle is running rich (black smoke out of exhaust). I've replaced high pressure pump, fuel filter, pressure regulator, and cooling temp. sensor. With key on engine off it has 40 pounds fuel pressure. The check engine light stays on constantly and the fuel pump runs constantly and when I try to get self test codes the light never blinks..it just stays on.

Check for air inlet at carburettor leaks. ... 1989 Ford F 150

I just bought a 2000 dakota with a 3.9 v6 engine it runs great at a constant speed for 6 or 7 miles then it starts acting like its not getting enough fuel sometimes it will actually die. I was told that the fuel pump had been replaced. when I had the codes there was a misfire problem so I have replace the plugs, wires, cap, rotor bug and the coil as well. Now the codes are still saying that there is a misfire but also a high low fuel pressure. So do I need to try replacing the fuel pump or is th

Just a quickie ,try it with the fuel cap off ?? ... 1989 Dodge Dakota 2WD

I have a 1988 camper it's on a Ford F350 chasse with a 460 ci. engine. Has one gas tank with a low pressure pump in it and a high pressure pump on the frame rail. The truck runs for an hour and dies. at that point there is no fuel pressure or spark and the high pressure pump is hot. I replaced the high pressure pump and the fuel pump relay but it didn't help. Can anyone tell me why the high pressure pump could be getting hot and would it cause it to not have spark ?

The catalytic converter may be fried. Very poor design of the restricted exaust ports.\015\012 And the fuel pumps are junk straight from the box. Around 94 Ford had to change the design of the fuel pumps.\015\012 I am not a mechanic but ... 1988 Ford F 350

How much psi does the mitsubishi cedia GDi gas tank pump push to the high pressure pump

... Cars & Trucks

1997 Saturn sedan won't shift into reverse. Have changed valve body, problem better for a few minutes, then came right back. Inside of trans looks good, no clutch smell and when it does get into reverse it is late with hard shift, but it's solidly in reverse, so there's no problem with reverse clutches. Also sometimes late going into second, but sometimes no problem. Dealer tested pressure and said it was inconsistent but passed high pres test- so probably not the pump. It's getting error codes

There are a few things that it sounds like it could be to me:\015\012\015\012\015\012Misaligned lockout ring- this is what is supposed to keep you from accidentally going into reverse\015\012Shifter cable is ... Saturn SL2

How much psi does the mitsubishi cedia GDi gas tank pump push to the high pressure pump

... Cars & Trucks

I have a 94 chevy cavalier z24 with a 3.1L engine. The ABS light comes on and sometimes the e-brake light stays on as well. I can clear the lights if I just shut off the ignition and turn it back on again. But the lights periodically come back on. I tried pulling codes by jumping power to ground on the dlc. I get a flash code 12 wich apparently means nothing as it pumps that code out at the beggining and end of the flash code cycle. So Do i need a separate scan tool to get the abs code or shou

... 1994 Chevrolet Cavalier

Gdi high pressure pump

... 1999 Mitsubishi Galant

Not starting! 98 s10 -2.2 4 cylinder. the truck cranks over gets spark checked the fuel pump, pressure is what its supposed to be. no bad codes according to code reader. get good gas pressure through the rail that leads to injectors.everything i've checked says it should start but doesn't. when you first try it after its set for a couple of hours it tries to start for half a second. if u spray starter fluid direct through the throttle body it pops and tries? I'm baffled any advice appreciated

Check and see if the Injectors are firing. Disconnect one of the injectors and use a test light and paperclip. Put the paperclip in one of the disconnected injector connectors terminals, clip the testlight to the paperclip. Now touch the tip of the ... 1998 Chevrolet S-10 Pickup

2002 Durango 4.7L 2wd. It would not start; starter checked [it was ok] and a relay switch replaced. It then started for a short period then it refused to start. I had several scans and point checks done. Nothing was found, but the fuel pump was not getting fuel and I kept getting a “no bus” code. I was told it was the PCM and I had it replaced [flashed and coded]. It still would not start; Replaced fuel pump; would not start; Replaced/fixed catalytic converter-no luck. Replaced ignition


1993 Chevy Blazer 5.7L V-8, with 250,000 miles on it. The motor runs great. At a cold start up the oil pressure is near to 60. As the motor reaches 200 dregree, it begins to lose oil pressure. Soon the oil pressure will go to zero and the lifters will start ticking. Turn the engine off, let it cool. Starting again at a cool temperature, oil pressure is near 60 until it get warm. Would a new oil pump, or high volume oil pump give the motor some extended life??? Thanks Tom

Yes. Definitely. The oil pump is just weak. The veins in the oil pump get worn and to not keep the oil pressure up. Along with the oil gets thinner as the oil warms up. It makes it more difficult to pump. Another suggestion is Slick 50 for high milea ... Chevrolet Blazer

Parked car running 6 months ago. went to get it no fire also no fuel. tryed the on off on off on key switch to get code and no flashing light. did pull pump and would not work when i applied power so went ahead and replaced pump and no fire reaching new pump

Fuel pump relay is defective. Or inline fuses since it's a 1999 you would not get a code if the pump didn't work. However your connection tot he fuel pump could be bad or the inertia switch could be bad try pushing the reset button to see if it ... 1988 Dodge Omni

I have a 2006 mitsubishi lancer. The a/c works intermittently. Works the least the hotter the day gets. The presures are 25 low side & 145 high side @ idle. What are the proper pressures ? I beleive this systems runs @ lower pressures than the older cars. The high pressure switch works & cycles the cooling fans. the compressor sometime cycles and not @ others. Does anyone know of any usual suspects??

... 2003 Mitsubishi Lancer

Have 1995 jeep cherokee v6 4,0 my jeep run sluggish loss of power cant get over 65 mph service engine light on took it to auto parts to get code read low fuel intake somebody told me also to start it 3 times then read the flashing light where can i get a list of information on the code names. what should i check for the low fuel intake? the fuel filter maybe the pressure tested please help

This sounds like you may have a problem with your oxygen(O2) sensors or a clogged component in your exhaust system. if you have a catalytic converter in your exhaust system, the filter element inside could break up and clog the exhaust pipe. you shou ... 1995 Jeep Cherokee

It wont start the fuel pump is good its getting good fuel pressure but when it stop running it acted like the fuel pump went out so i put a boat tank and high pro pump and it sits the and cranks but n

Do you have a bad crank sensor and the injectors are not firing ? ... 1988 Pontiac Bonneville

I have a Mitsubishi 2.4 GDI Automatic Spacewagon year 2001 . Idling is irregular, engine light flashes on dash, and won't rev past 3000rpm. Fault code from test is P1221 and auto electician said he thought it was the throttle alignment control that was faulty. Throttle body was changed and is new, so not that. When code is cleared and engine revs are kept at above 4000rpm fault does not occur, however,fault returns if revs are dropped to less than 3000rpm and the engine light flashes again.

P1221 is throttle position sensors , therefore the electrician was right, check wiring to TPS, particularly if the throttle body has been replaced, that can be the problem.If\015\012the sensor is not related with the engine ... Mitsubishi Starion

I have a 1992 E350 motorhome with a 7.5 in it. I just had to replace the fuel pump. After replacing the pump it idles rough and runs rich. I did pick up an engine light and after getting the codes replaced the oxygen sensor. Problem still exsists. I am thinking my next step would be the fuel pressure regulator. I appreciate any help I can get.

There is a few options but first I am hoping with your fuel pump replacement that you replaced the fuel filter if not do it first. next have you checked you throttle body idle speed control device... See below on diagnosticsThe curb and ... 1992 Ford F250

Ok so my 02 mustang gt was throwing a code forever, witch was P0113, intake air tempature sensore high input. after finding out my intagrated iat sensor was malfunctionaing i replaced it with a external one on my cold air intake. ever since then ive been getting codes P0171 and P0174 both banks system running too lean. i can not get them to go away. ive tried checking the fuel pressure. the fuel filter was changed i cleaned my MAF checked for vaccum leaks didnt find any fuel injectors are work

... 2002 Ford Mustang

Hello I have a 1997 toyota Camry with 182000 miles on it. When I started my car my check engine ligth stay on. I went to Auto Zone to get it troubleshooting and a code P0450 came up it also states evaporative emission control system pressure sensor/switch and probable cause a Faulty pump module. Do I just get the pump module replace or could it be something else?

Dear corliss_rich,\012I just googled po450 code and found the there was a settlement on Toyota Camrys from 96-01 involving Evaporative Emmissions Control system sensor. Check web page. Toyota may fix for free. I have same problem on my camry. ... 1997 Toyota Camry

I have an 1988 ford E-350 7.5L. After an hour or so of driving it develops a skip which gets worse until the engine stops running. It then takes 20minutes or more before you can start the engine. I have replaced the high pressure fuel pump as well as the ignition coil and the electronic ignition module (TFI) the low pressure fuel pump was bypassed at one point with no positive results either. Please help!!!!

... 1988 Ford F 350

99 blazer has been hard to start for awhile but will start after a few tries now wont start at all. It will turn over but sounds like it is not getting enough gas. The fuel pump is only a yr old and you can hear it clicking on and it is getting gas up to where you check the fuel pressure. it has had a recent tune up and a cold start sensor. Our neighbor use to be a mechanic and has a code machine, He said it isnt throwing any codes and that it may need a computer. I am not sure this is correct.

Check the fuel pressure, these vortec motors need 60 psi of fuel pressure to start. Anything less than 50 and the poppet valves won't open. If fuel pressure is sufficient, check the coil wire ... Chevrolet Blazer

I am working on a 2000 Ford Taurus with a 3.0L that has 215K on it, It has several codes that came up, the first is a P0191-Fuel Rail pressure sensor circuit range/performance, P1237-Fuel pump secondary circuit fault, and a P0300 Random/Multiple misfire fault that probably came along with the rough running engine from the injector circuit fault. I checked the fuel pressure and I am getting 42psi and it should be 50 to 56psi with the engine running. I have replaced the fuel pump and filter, but g

Where is the fuel pressure located on the 2000 ford taurus exactly? ... 2000 Ford Taurus

1999 Nissan Maxima wont turn over. It cranks, but wont start. It isnt the battery cause its new. My friend said it may be an electrical problem or fuel pump. How can i determine if i am getting a spark? My friend tried to start car and he did something with the fuel line to determine if it was getting pressure and it was. Not sure if it is enough pressure. He also used an older computer but it was only giving the error code for emissions. Any ideas?? Thanks.

Need three (3) things for an Internal Combustion Engine to run, FUEL, COMPRESSION, & IGNITION. To check spark, pull a plug wire and connect to a spark plug that is sitting on a metal (grounded) surface and crank the engine over. You should see ... 1999 Nissan Maxima

99 grand cherokee 4.7 v-8 engine missfires at rpm's under 2000 ran compression check [good] coolant system check [good] obd only one code p0500 vehicle speed sensor changed plugs,checked spark at coils [good] plugs carbon up after or 15 minutes black inside throttle body drained fuel, added clean fuel , gas dryer, and injector cleaner suspect high pressure in fuel rail, but have'nt tested yet try to relieve fuel pressure by disabling fuel pump after disabling pump, engine runs much b

It is most likely the fuel pressure regulator,it will have a vacuum line going to it,make sure it is getting vacuum,and the hose going to it is in good shape.Ether the regulator is bad,or the return line going from the fuel rail,to the fuel tank is r ... 1999 Jeep Grand Cherokee
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.1263 seconds