Having problems with your 1999 Jeep Cherokee ?

Kevfos12after initial start up my jeep acts like its about to stall almost like its coughing,have a new fuel pump and had a fuel line clean and current with my oil change

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Try changing the egr valve, and check the plugs and wires, also could be the o2 sensor
Repair Help & Product Troubleshooting for 1999 Jeep Cherokee

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kevfos12after initial start up my jeep acts like its about to stall almost like its coughing,have a new fuel pump and had a fuel line clean and current with my oil change


Try changing the egr valve, and check the plugs and wires, also could be the o2 sensor ... 1999 Jeep Cherokee

My L300 4x4 Starwagon surges on occasion when driving. I Changed the fuel filter, cleaned out the tank, & checked fuel lines, & changed fuel suppliers several times but it still persists. I've had the pressure checked 3 times & each time comes up good. I suspect the fuel pump is on the way out but I can't spend $200 Aus to find out. Any suggestions about the surging cause? Is there an electric alternative pump that can be fitted outside the tank? Something like the old SU pumps fitted to the Mor


... 1990 Mitsubishi Minivan

Noise engine noise with oil warning lamp on, This noise sounds like tappet noise, I got the cylinder head cleaned and changed the engine oil.after this we checked the entire oil line cleanes , the oil pressure meter is showing low pressure however the oil pump is ok.still the noise is there, we have cleaned all the oli line in the cylinder head , cam, and casings, I HAVE OPEL CORSA 1.4 2003 MODEL,I AM UNABLE TO FIND THE PRODUCT CATAGORY IN THE LIST BELOW , GIVING FALSE CHEVIRLET ENTRY , PLEASE E


This sounds like bad main and connecting rod bearing they are worn and when they become worn they make noise. Because of excessive clearance between bearing oil pressure drops therefore starving the essential parts of the engine of oil. ... 1998 Chevrolet K1500

Noise engine noise with oil warning lamp on, This noise sounds like tappet noise, I got the cylinder head cleaned and changed the engine oil.after this we checked the entire oil line cleanes , the oil pressure meter is showing low pressure however the oil pump is ok.still the noise is there, we have cleaned all the oli line in the cylinder head , cam, and casings,


Do an oil pressure check at the oil filter.If the pressure is low, replace the oil filter.Remember if you do it yourself before replacing the oil filter pack it with vasoline first.If you don't, the pump will not start pumping. ... 2004 Chevrolet TrailBlazer

I have a problem with my 1996 mitsubishi pajero 2800cc turbo diesel. Sometimes when I am running, it seems like the fuel supply to the engine is suddenly cut-off and the car starts losing power until the engine shuts off and does not start. after a few minutes or after I manually operate the fuel pump the engine would start again. I have checked the fuel line cleaned the fuel tank and changed the fuel pump and filter. this is very dangerous especially if going fast or downhill because I lose


When i change engine oil in pajero 2800?\012\012\012please give chart? ... Mitsubishi Montero Sport

1993 Buick Roadmaster keeps on blowing fuel pump/ecm in-line 20 amp fuse. Car stalled out in a parking lot, would not start, no fuel. Changed fuel pump, fuel filter, fuel pump relay. Found fuel pump/ecm in-line 20A fuse keeps on blowing when I turn key on. Looked all over for shorts, disconnected oil pressure/ fuel pump cutoff switch, changed fuel pump relay, fuel pump is disconnected at tank at present, still blows fuse. Please help as I cannot afford to take car to shop and presently working


You said the fuel pump is disconnected at present and the fuse still blows so I am thinking you have a dead ground in the fuel circuit maybe a wire is pinched after the fuse and before the pump. Check along the frame for this and make sure all of you ... Cars & Trucks

Neon 2004 My car runs great then all the sudden it is like the gas is chocked off. starts to chug and dies. I shut the car off and start it back up and it runs again. The engine light will not go off. . I replaced the fuel pump , black nasty rust came out of the fuel pump, then I changed the injectors sprayed cleaner into the old injectors and the same nasty black stuff came out of them also. I also cleaned out the gas tank and blew out all the lines. Thought I got it running again, but after 20


Disconnect the mass airflow sensor and see if the car runs ok...... ... 2004 Dodge Neon

1996 suburban random misfire or runs rough changed the following sensors: O2 (all four) MAF IAT ECT and PCV, air filter, water pump (flowkooler), thermostat, cleaned ground connections then I added Lucas fuel system cleaner and now seems like the engine is not getting fuel and cuts out changed the fuel filter no improvement suspect fuel pump, due to fuel cleaner additive would like advise before changing the fuel pump ($410 at local shop)


I would check the fuel pressure first if it is in the good ranges then your pump is good. have you checked your spark plugs and wires? if not i would, if bad replace. otherwise i would have the ignition coils checked to find out if they are working c ... 1996 Chevrolet Suburban

I GOT A 1996 FORD EXPLORER TRUCK RAN FINE AND FUEL PUMP WENT OUT CHANGED FUEL PUMP AND TRUCK RAN LIKE **** THEN WOULDNT RUN AT ALL CLEANED EGR VALVE CHANGE SPARK PLUGS EVEN CHANGED FUEL PUMP AGAIN CHANGE FUEL FILTER AND MADE SURE IT WAS RIGHT FUEL PUMP TRUCK STARTS UP AND THEN DIES RIGHT AWAY PROBLEM DIDNT START TILL I CHANGED FUEL PUMP. cOULD IT BE SENSOR ON THE FUEL TANK ON TOP IF ITS NOT SEALED RIGHT?


The truck starts but stalls as soon as the key goes from the start back to the run position?Have you tried keeping your foot on the gas as soon as it starts to see if it will stay running?If it does and then stalls as soon as ... Ford Explorer Sport

We just got a brand new battery and starter(i know the solenoid is on the starter) for our 98 windstar. 3 weeks later we got an oil&filter change,as well as fuel filter&fuel injection cleaning, and now it acts like it doesn't want to start(could the guys have knocked into something?). it's not turning over all the way.my husband has pressed the fuel inertia switch in the past, and its worked before, but not now. it could be a # of things(distributor cap, pcv valve,fuel pump relay, spark plugs, i


Does it just crank and crank,or does it barely try to start.Check fuel pump relay under hood or for a fuse..Or turn the ignition to the run position but dont start it and have someone listen by fuel tank for the fuel pump to make the humming noise.Mo ... 1998 Ford Windstar

I own a 2002 GMC Sierra 3/4 ton. I have cleaned the injectors, changed fuel filter, changed oil and filter, replaced tires, but she is still fluttering and then dyeing. The RPM's drop and it feels like I am not getting gas to where it needs to be. I pump the gas petal and sometimes it stops it from dyeing. What is wrong with my girl??


Hello,\015\012You have a bad oil pressure switch. I know that sounds strange but It feeds the fuel pump. Some times randomly the PCM does a self check and shuts off the fuel pump relay when it does this it runs off power from the oil pressure s ... 2002 GMC Sierra

When I reach 65 mph in my 1994 ford explorer,I lose all power.When I push the gas pedal,it barely revs.When it gets to about 20mph,it picks back up like nothing was wrong.But if I reach 65,it happens again.Have replaced back cat convertor,fuel pump,fuel filter,O2 sensor,plugs and wires,oil change,new battery,new gas lines and the trans has been rebuilt twice.It has been in 2 shops both for over a week being diagnostic tested.They have checked sensors as well.PLEASE HELP.


... Cars & Trucks

I have a 1986 nissan 300zx non turbo. oil prssure will not build up. keep addin oil but all its doing is smoking out the exhaust. acts like the strainer on the fuel pump might be stopped up. can i clean fuel pump strainer without diassembling the whole fuel pump? also i added a product that was supposed to stop oil leaks. can u give me any advice


Dear number601513: DANGER!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\015\012Adding oil is not going to make the oil pressure build up by adding more. The system is slightly more than a 4 qt system with an ... 1986 Nissan 300ZX

The vehicle fails to start. The lift pump does not presurise the fuel system. Vehicle starts after bleeding is done on the injector pump. vehicle on the road runs perfectly. At idle speed the vehicle "hunts" as if there is afuel starvation. Upon switching the car off, it fails to start again.Every time we clean the tank , oil appears in the fuel. I have used a seperate rubber fuel line from the tank to the lift pump, thinkig there was a hairline crack in the metal fuel line. Filters have been ch


Filter is always dirty meaning the tank is corroded. The clean doesn't get rid of corrosion since there is no special coat remained on the surface. This caused the fuel rail is bad now. you had a great idea to run a rubber line to by pass the fuel ra ... Nissan Pickup

During an oil change at jiffy lube, the car drove in fine, but once the oil change was done the car wouldn't start. The engine would turn over and it looked like the engine was shaking around a lot. They noticed oil had leaked into the air intake system even into the air filter. They eventually added fuel cleaner that some how cleaned the fuel system and got the car started. Is this a oil leak into the exhaust system? Is it fixable?


Many times when oil appears in your air intake and in the air filter this is usually caused by a plugged pcv valve Positive crankcase ventilation valve it costs anywhere from 3-10 dollars.As far as it not starting my guess is they checked the air fil ... 1997 Subaru Legacy

1998 Ford explorer , had sitting every winter months in garage, usually start right up every spring. put in charged battery,,would not start. Seems like the fuel pump is not pumping out any fuel. I loosened a fuel line,,nothing when trying to start. Why would fuel pump go bad when not in use? How to change fuel pump if need be? Is it in tank? Any other causes that would be the problem? Thanks


The pump is in the tank. The tank has to be droped to replace it. Pumps can go bad at anytime without warning. A failing pump you may not have noticed but can go bad when sitting. Try checking the autoshut down relay and fuses assiciated with the pum ... 1998 Ford Explorer

I just did an low end job on my 1993 ford f250 7.3 liter deisel pickup which means i replaced the rods, mains, and oil pump in the engine. i lined the gear timing marks up on the crank, cam, and fuel pump gears. and now when it starts it cranks fine but it smokes like its getting way too much fuel and it idles really rough. it was running fine before i did the job with my dad but it was loosing oil pressure. now that i done this to the engine it has great oil pressure but runs rough until you ge


Out of timing ... Ford F-250

Missfire ok when i drive the car it runs fine for a good while then it feels like the car misses a couple times then the cel comes on then goes, tonight i took it for a drive and as soon as the secondary turbo starts to kick in it starts to **** really bad. i just put a new good working engine in it, new oil, oil filter, coil packs, spark plugs, i havnt changed the fuel filter dont think its been changed ever its done 197k;s could it be the ecu or fuel pump or fuel filter?


I would check the fuel pressure sounds like it could be low when there is a power load put on it. ... Subaru Legacy

Water in gas tank and fuel lines on a Chevy 1998 S-10......wont throttle up at all, will run at idle.....when throttle up it chikes itself out like it flooded...but will idle as low as 400rpm..have changed fuel filter and air filters, ran beerymans B12 cleaner thry almost 3/4 tank......someone mentioned a rest button on fuel pump..but I find that it is only IN the tank.....is this true? is there any other way to access th reset for the fuel pump? Does the fuel pump have a switch that shuts off i


THERE IS NO SUCH THING AS A RESET SWITCH ON THE FUEL PUMP. IF YOU HAVE WATER IN THE FUEL SYSTEM THE ONLY THING YOU CAN DO IS REMOVE IT, PHYSICALLY. DROP THE TANK, CHANGE THE FUEL FILTER, REMOVE THE THROTTLE BODY, AND GET RID OF THE WATER. AND DON'T ... 1998 Chevrolet S-10 Pickup

I have a 2003 Olds Alero. Last week the oil change light came on. That same day, it suddenly started running rough when idling. Things I've done to try to fix the problem: * Fuel pump was replaced November 2009 (unrelated to the current problem, but something to know) * Changed the oil this week * Added Sea Foam to the fuel * Visually checked for vacuum leak I live in Ohio, and the car has about 120,000 miles, should weather and mileage make any nevermind. Thanks!


... 2003 Oldsmobile Alero

I have a 1996 c280 and up until last week had not had any problems so far with it starting, and so i turned it off as usual and then later on when i went and tried to restart it, my car it won't start it just cranks. Seems like it's the fuel pump I'm a girl so i asked my dad, an brother end they said the same. It has gas also a oil change and tune-up a few months back. How do I change the fuel pump???


Welcome to FIxYa.com\012\012Location of fuel pump\012\012\012\012 Crimp line coming from fuel tank a ... Mercedes-Benz C-Class

Fuel pump went bad what does the fuel pump look like and were is it located and how long will it take to change it.could it be line that is clogged up? because may be its the line what do you think.well i checked the fuelpump reset button and its down which means it went bad.


If the fuel pump failed.\015\012Remove the fuel tank from the vehicle.\015\012Then remove the fuel pump from the top of tank\015\012Will take you all day\015\012Lines are not clogged\015\012Reset is down and okey ... 1997 Ford Crown Victoria

99 monte carlo 3.1, starts and idles but stuters and almost stalls if gas is pressed. Suspect fuel prolem. In process of changing filter but of course this original filter was siezed on. Had to cut steel fuel line and now I have a project. Have a new fuel pump and fuel pressure regulator ready. Would like to check fuel rail pressure before replacing $350 pump but do not see a place to check it. Some other problem other than fuel?


You can connect a pressure tester where the fuel line goes into fuel filter, Make sure you clamp the hose to the line and tester before turning key on. You should have 45-50 pounds pressure, If not? replace pump ... 1999 Chevrolet Monte Carlo

I have a 85 corvette , show a code 45 which is rich exhaust. Book says to check evaporative charcoa canister (done, check fuel pressure regulator, (replaced), check EGR and oxygen sensor, (both replaced). also a new fuel filter, fuel pump, cleaned fuel lines and fuel rail, and cleaned and checked all injectors. Replaced the Electronic /control Module, still very rich exhaust, seems like trying to flood out and still gives a trouble cod 45. What have I missed. Any help would be greatly appreciate


Check the vacuum hoses and the Map sensor I had problems before cause of that Map senor. ... 1985 Chevrolet Corvette

I have a 96 dodge dakota 4-wheel drive 3.9 engine automatic pickup i have changed out one outside coil one on the outside of the motor the other underneath the rotary bug. I changed out the rotary bug distributer cap spark plug wires spark plugs three O2 censors took out the catilatic converter muffler fuel pump fuel filter cleaned out fuel injectorsand fuel rail. The timing on the scanner shows to be okay and fuel shows to be okay and everything else shows to be okay like the check engine light


Take off dist cap.turn rotor one way then the other. if the tip of the rotor moves more than 1/16 of an inch of free travel then the block bushing is worn out. the block bushing is bronze and it holds the oil pump drive shaft in perfect alignment. wh ... Cars & Trucks
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.6518 seconds