Having problems with your 1999 GMC Suburban ?

My ac stopped working all thr fues are good but the compresoer cluth dose not engage is it bad

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

1.a/c system has leak? if no freon in the a/c system the compressor won't engage. \015\0122. check compressor clutch relay.;\015\012if everything ok, it could be bad a/c compressor. \015\012hope this can help.
Most likely low,or out of freon
Repair Help & Product Troubleshooting for 1999 GMC Suburban

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ac stopped working all thr fues are good but the compresoer cluth dose not engage is it bad


1.a/c system has leak? if no freon in the a/c system the compressor won't engage. \015\0122. check compressor clutch relay.;\015\012if everything ok, it could be bad a/c compressor. \015\012hope this can help. ... 1999 GMC Suburban

I have 2002 Chevy s10 with ac issues. All blend doors and actuators work properly. Clutch engages on compressor. Blows warm air when ac is on. When I put a guage on it the psI stays on max and doesn't change. Could my compressor be bad and the clutch still engage? I've never seen a compressor clutch engage and compressor bad, is it possible. I think I've eliminated all else


... Cars & Trucks

I have a 2000 Mitsubishi eclipse gt that the starter quit working. We could here a click when turning the key to start. So im thinking the solenoid was engaging. But the starter was bad. I replaced the starter and it cranked and started right away. 3 weeks later the same thing happened. Thought it might just be bad luck and got a bad starter. Replaced it again and the same thing it cranked and started right away. Took the starter back to get it checked, it checked out and turned over like it sho


... 2000 Mitsubishi Eclipse

The AC on my 97 Ford Taurus only works sometimes. The clutch does not always engage. When I tap on it, it will then engage. What do I need to do? A few times the clutch only partially engages and it just rubs for a while without actually starting the compressor. If the clutch is bad, can I just replace it or do I have to replace the whole compressor? Thanks!


There is too much air gap between the hub and pulley. Usually, there are shims under the hub to set the proper gap. If you remove the small bolt in the center of the hub, it should slide off. There should be shims that look like small washers on the ... 1997 Ford Taurus

Electrical problem, the lights come on but the engine pre-heater, dash lights don't & the starter does not turn over. The batteries are up and all connections seem okay. Could the engine shut down relay or start relay have gone bad? All worked prior to parking and when I tried to start it this morning, the starter wouldn't engage and then the dash lights and engine preheater light wouldn't come on. Headlights work.


All of that stuff you describe is controlled by the PCM(powertrain control module) on the firewall passenger side. mine got shorted by an overly helpful drunk while jump-starting his neighbors car! you'll a wiring schematic to test if you have output ... 1997 Dodge Ram 2500 Club Cab

2002 honda cr-v. AC compressor clutch doens't engage. condensor fan doesn't run. ac blower motor works normally. AC compressor clutch and condensor fan work when i jump them out at the relays in the fuse box in the engine compartment. condensor fan comes on when radiator fan comes on. I think i have a bad ground somewhere?


... 2002 Honda CR-V

I have a 94 chevy 1500 4x4 the 4 whell drive is not working now the transfer case is good and i just replaced the accuator in the front axel it was bad it is working now but not engaging the front diff


Then t/case isn't good. ... 1994 Chevrolet C1500

When I turn the ignition all lights come on, radio works, air and heat work, everything is like normal except nothing happens. No winding sound, no starter engaging nothing just a click and it only makes that noise once not a continuous clicking. It did this one time before about 5 days ago and when I came back to it after it sat for an hour or so it started right away and have had no problems until now. I am guessing the starter is going bad or maybe an electrical problem.


Check the connections at the battery they need to be tight and clean. the starter draws alot more amperage than any other electrical componets. if all connectios are good than it sounds like the starter is bad ... 1998 Buick LeSabre

I cant dis-engage my cluth on my 94 mazda b3000 truck. Bled lines from reservoir but cannot get any tension on the clutch. I pumped on clutch pedel and the shift worked for about 10 min and now tension is gone and cant shift the transmission. bled air from line and still doesnt work.


Could be a throw out bearing or the shift fork is broke. ... Mazda B3000

1992 chev blazer tahoe lt.. 4 wheel drive worked last year. Tried to engage it this year for first time and would not go into 4Lo or 4Hi. Was in neutral. Start vehicle and green light on 4wheel option switch lights but does not do anything when trying to engage it. Bad Fuse??? I hope


Not a fuse if you have power to switch,if your 4wheel light does come on and is not blinking,check the little motor on the transfer case,tap it while someone tries the switch,it might just be stuck from not being use,if it doesn't free its self you m ... 2001 Chevrolet Tahoe

Starter solenoid on 1993 Ford E350 nwith 7.5 liter v8. Solenoid went bad, new auto parts store replacement, doesn't work right. When I turn the key to first click, the starter engages and the solenoid stays engaged. This is on an Itasca motor home, built on the Ford Econoline chasis


It sounds like the small tickler wires may be reversed to the Solenoid.\015\012\015\012If no success, call Itasca and ask if there were any changes for this Solenoid. There are several types of Solenoid with the grounding being the major ... Ford E-350

1990 Mazda B2200 PU. Clutch sticks to the floor and if held down eventually allows disk to engage. Can pull it up with side of foot before tries to engage, then works again. No noise from throw-out or clutch disk. Bled the slave cyclinder. Still sticks. I'm thinking the clutch slave cylinder may be bad. Cannot find a leak at upper end in hoses or Clutch master cylinder. However when first had problem did have loss of fluid in cylinder from Max to Min level.


I just had the same problem today it was the master cyclinder\015\012its a common mazda problem ... 1988 Mazda B2200

I have a 1999 chevrolet express van, the ac dose not work. i turn the ac on and the clutch dose not engage on the compresser.what could be the problem? i have checked the fuse and the relay. they seem to be good.thanks bruce


Bruce did you check the freon. if the pressure is not enough the ac clutch will not engage. If it is the freon you may want to use a leak detector from your local autoparts store before wasting freon. ... 1999 Chevrolet Express

I have a 98 chevy express van,My A/C compresor relay dose not engage when you turn the switch on but if you unpluge the relay and put back in with the switch on it will work, turn the switch off and


1) you must test the wires connector from corroded cables , clean it2) Test the voltage for 12vdc for input to the coil of the relais.3) If there are NOT, test the fuse for open and replacle, the fuse box in the hood motor, see the instructi ... 1998 Chevrolet Express

92 BMW just put flywheel in but did not take it apart.when trying to start the starter turns but benddick's doses engage took starter out an jumped it with cable's an benddicks works so i think i have wires hooked up wrong have book but shows nothing so looking for something to look at that will show me how wires are hooked up


Check to see if the flywheel is bent by turning it . sometimes when changing a starter or flywheel you may need shims to make sure there is the correct clearance is maintained between the starter and flywheel otherwise the teeth of the gears may n ... 1994 BMW 3 Series

2002 xtype will not try to start. All lights and instruments strong. Was working park and the next day wont start. Starter not engaging only hear to popping noises, continues after the key is removed for a few seconds can a starter go bad overnight?


Hi yes unfortunatly starters do have a habbit of dying, actually it is not normally the starter itself but the solinoid connected to the starter, you can try this to see if it will unstick it, get a friend to turn the key as if to start the car, and ... 2002 Jaguar X-Type

A/c does not work clutch will not engage is there a relay that might have gone bad and where can I find the switch


AC systems have a pressure switch that won't allow compresser to engage w/o enough freon in system.they sell an inexpensive hose,gauge,& can of freon kit at auto stores.look for the kind that has dye in it to show if you have a leak. ... 1997 Chevrolet S-10 Pickup

I have a 2003 camry,4 cyl engine auto trans,143000 miles on it, just replaced the trans with used unit with 20,000 mile on it, car dose the same thing, when shifting from 2nd to 3rd it holds the shift high then bangs, or sometimes slips, if car is manually shifted works perfect on original trans, fluid was discolored and burnt smelling, also slow to engage into reverse,the used trans shift to reverse fine, the cooler was also flushed out before installing


Usually burnt and discolored ATF mean pump or torque converter not doing there job or bands and clutches are worn. Shift solinoid or a pressure problem is the problem with 2nd and 3rd gear, Take it to a transmission shop and have them look it over ... 2003 Toyota Camry

I have a 2002 ford f250 7.3l diesel that 3rd gear when trying to engage would act as a engine break and instantly slow you down along with greatly reduce the rpms and struggle. after i noticed that i checked the transmission fluid and it was a quart and a holf low. i topped it off and the problem continued. so i limped home running it into second gear until i got to a high enough speed to catch overdrive after that 3rd gear started working fine but now second slips bad, doesnt wana shift into se


... 2002 Ford F250 Super Duty SuperCab

2000 gmc jimmy wont start fuel pump comes on and cuts off but will not start.I have changed the fuel filter and that did not work. Is the pump not building the pressure it needs to start or would my pressure regulator be bad. Pressure at start should be 60-66 psi and it dose not look like it is getting that when it is turned over and the pressure valve is pressed. Nothing happens when I depress the pressure valve after trying to start it and no one is turning the key to crank it.what could this


When you hook the pressure test guage to shrader valve on fuel rail what it reads is what the pressure is from pump, around 60 p.s.i. all you need to do is hook up the guage and turn on key, you do not have to turn engine over, and if pump is good it ... 1999 GMC Jimmy

I did a radick on the transmission iator flush and installed a "T" in one of the heater hoses, while the flush worked for the radiator, I did not notice that the dipstick on the transmission was NOT seated down all the way, and evidently a lot of water got into the tranny fluid, because my car would not shift after driving it for a few miles. I checked the tranny fluid and it was mixed with water, I drained the bad fluid and put in new fluid, but the tranny still will barely engage into drive


There is no simple fix. The water damaged the hydraulic control solenoids and most likely burned the clutches. I am sorry to say it is time for a rebuild. ... 2008 Chrysler Sebring Convertible

The light comes on but the front end does not engage the vacuum acuator does not move it is in working order no splits or tears, is it a vacuum leak , i cannot pull the cable manually from the front diff so is it bad,inside the front diff


There is a vacuum switch on the top of the transfer-case on the\015\012driver's side that has gone bad. It's common on out jimmy's and will\015\012need to be replaced. Auto Zone or Parts Source will have that part and\015\012can give you the step by ... 1996 Chevrolet Blazer

2000 gmc jimmy wont start fuel pump comes on and cuts off but will not start.I have changed the fuel filter and that did not work. Is the pump not building the pressure it needs to start or would my pressure regulator be bad. Pressure at start should be 60-66 psi and it dose not look like it is getting that when it is turned over and the pressure valve is pressed. Nothing happens when I depress the pressure valve after trying to start it and no one is turning the key to crank it.what could this


The fuel pressure if leaking could cause this the regulator is located under the intake plenum but you should smell gas .if you dont then most likely the pump is bad ,the pump will come on for 2 seconds when the key is on then go off it will not stay ... 2000 GMC Jimmy

The cluth only occasionaly will not disengage. It will work perfectlty for a week or so the as you are driving and go to change gear the pedal goes to the floor with no resistance but does not engage the clutch. The master cylinder appears ok and does not leak oil. The local Mazda dealer cant find the problem.


I would change the master cylinder,or fit new rubbers as it sounds like the rubber is turning in the bore or its just worn ,beleave it or not the rubber can actually wear the metal away ... Mazda 323

Horn cutts out when pressed., sometime works other times does not. After removing the airbag insert and reinstalling it AND the clockspring being replaced the horn sound on its own! So to shut it off I had to bypass the horm and install a momentatry on button to engage the horn. But doing that the horn stops sounding but stil intermittantly cutts out when the button is pushed. Does this sound like a steering wheel/colume problem or maybe a bad connection in a wire leading to the horn? where is t


Your horn maybe have a short circuit on it.\015\012replace the horn and this problem must resolved. horn is alocated rear grille, and before radiator. ... 1999 Plymouth Voyager
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.7869 seconds