Having problems with your 1999 Ford Windstar ?

Code p1260 what is the problem - 1999 Ford Windstar

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 1999 Ford Windstar

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Code p1260 what is the problem - 1999 Ford Windstar


... 1999 Ford Windstar

I have a 2000 ford windstar with the airbag warning light flashing a 3-4 code series....what would throw such a code and can I address the problem myself...outside the ford dealership


... 2000 Ford Windstar

2002 Ford Windstar . Engine light is on. took it to auto zone for a test. codes that came up was p1120 & po122 . that comes back as Thottle Position Sensor for both codes. Changed it and still not solve the problem. The problem is runs good on a flat road. But going up a step hill you lose power. Pedal to the floor does not speed up. Also drove the van with over drive up the hill when you lose power. and without it on it runs up the hill good.


Could be a wiring issue to the tp sensor its self or a problem withe the throttle body or pcm ... Ford Windstar

My 98 ford windstar is displaying trouble codes p1537/p1538, along with a misfire on cylinder 1 & 2 (p0301/p0302). what are some problems that can cause this problem?


Codes p1537 and p 1538 are codes for a faulty IMRC valve. They are located on the lower intake manifold. \015\012\015\012Intake Manifold Runner Control (IMRC), Vacuum Control\015\012\015\012\015\012\015\012Remove E-cl ... 1998 Ford Windstar

2003 Ford Windstar - no crank/start problem. Our 03 will not crank on cool (65 degrees and lower) mornings but will start later in the day when it is warmer, Have changed - alternator, starter, ignition switch (electrical), TPS (aka - neutral safety switch), battery and changed out several relay and fuses. Checked ground in three places - clean and secure. This a.m. mechanic tried to read codes - only thing coding was that the key was not being recognized - yet it would and does start on oc


... 2003 Ford Windstar

Problem car reflects code P1537 how can i fix this problem with my car is a ford windstar 1998


Intake manifold runner control problem. IMHO, this is a completely unnecessary system. Is often problematic.\015\012check out this link for more info:\015\012 ... Ford Windstar

96 Ford Windstar, 144K miles. O/D light is flashing after car runs for 2-3 minutes. Hard thunk from P to D but not from 2 to D or 1 to D. All gears shift smooth while driving. Rec'd code P1748 - Trans problems - Duh. How do I diagnose further? Also, transmission shop stated "fluid varnished" and recommend complete rebuild at $1k (codes read and test drive - no visual inspection). Any thoughts?


Yes. Having owned a trans shop,varnished means burnt clutches. Pull it and have it rebuilt. Your looking at ,at least $1800.00. No one rebuilds a transaxle for a thousand dollars. Not even if you pull it and carry it in. ... 1996 Ford Windstar

I need the wiring schematics for the range sensor/neutral safety switch, for a 2003 ford windstar. my brother cut the original harness plug off & replaced it with a different one that has different colored wires, i was having a connection problem & me not knowing he had changed it with a different color code wire plug i disconnected all the wire to fix the connection, when i was going to put it back together i came to find out that the vehicle harness & the plug had different colored wires & now


... Ford Windstar

Code 171 How to correct problem - 2000 Ford Windstar


Change the isolator bolts and the gaskit this will remove codes 141 171 i did this over the summer\015\012of 2010. you can get the parts at ford dealership.took me about 4 hours . ... 2000 Ford Windstar

Code P0171, what is problem - 2003 Ford Windstar


Code p0171 refers to system too lean, bank 1 causes---intake /exhaust leak---AIR system---MAF/VAF sensor---fuel pump pressure/pump---injectors---HO2S (Oxygen sensor)Replace the faulty units with genuine one because mostaftermarket units are ... 2003 Ford Windstar

I have a 2002 Ford windstar with codes u1262 and b1446. What is the problem?


... Cars & Trucks

2003 ford windstar. The engine idles fine when you rev up engine it has a miss.ODR II says no codes to report. Problem just started yesterday and car is undriveable


You hav a engine misfire ... 2003 Ford Windstar

Emissions test code comes up as 0743 torque converter circuit problem. how do you fix this on a 1998 ford windstar 3.8l engine?


U have a problem in the transmission torque converter clutch control circuit, most likely the solenoid switch that applies the lock up clutch of the torque converter is defective or a the torque converter itself is defective, the trans p ... 1998 Ford Windstar

I am having a problem with a 2001 ford windstar. Can you help me? i have codes 171 and 174 systems running lean bank 1 and bank 2?


Two bad O2 sensors is rare. The problem is before the sensor,intake vacuum leak, injector lower o-ring, IMCR stuck open or the control rod is off, vacuum hose(s) off, or MAF sensor. If this has a plastic upper intake, they had problems with o-rings. ... 2001 Ford Windstar

The problem is code po1401 - 1999 Ford Windstar


Replace the pdfe and pcm relayclean the egr valve and clean out the carbon out of the throttle body ... 1999 Ford Windstar

I have a 98 ford windstar 3.8 with a engine miss and two trouble codes, po401 and 402, would a bad EGR valve cause this problem?


I replaced the coil pack on my friends wind star when they had a mis. If you take the sparkplug wires loose and just set them on the plugs loose it will be easy to remove them with the engine running. Useing plastic plyers or some kind of insulated g ... 1998 Ford Windstar

Sir, My ford windstar 1998 give me the code P0174,sytem too lean(bank2), can you tell me what the problem is , it gives a heavy white smoke when i start the engine . just put a new cylinder head gasket ,had gasoline in tank for almost a year.


It's an intake gasket. Another option, however rare is the air flow meter. But not likely. The white smoke is most likely antifreeze leaking into either a cylinder, or the intake and entering a cylinder, exiting as white smoke. The bad intake gas ... 2001 Ford Windstar

Problem with the 2003 Ford Windstar Code P1518 intake manifold runner control stuck open...what do I do?


... 2003 Ford Windstar

I have a ford windstar p1744 code 98 with and fix the problem as


... Ford Windstar

Transmission problems 99 ford windstar 3.8.transmission o.d. light keeps flashing getting codes 743,750,755,760 trani was bad already replaced that w/used trani still trani dosent shift and keeps popping fuse 19 in engine compartment fuse panel have traced many wires to find nothing seems bad can you please help me jim from gomies garage in rochester thanks


Wow with all those sol probs if i knew the trans was working id suspect an ecm problem ... 2004 Ford Windstar

What is the problem with the dionest, code P0174 on my 1998 ford windstar and P0171


171-174 are lean codes.Check the PCV lines(Plastic tubes) At the ends you'll find rubber "elbows" to connect to the intake.\015\012I'll almost guarantee you one of them is ruptured and collapsed, this is a NOTORIOUS Ford fault ... 1998 Ford Windstar

P1151/po455 these codes pop up the 98 ford windstar runs ok until the engine heats up then spits and sputters loses speed and can die p1151 says its a gasket what is po455 and will it fix the problem


... 1998 Ford Windstar

Ford windstar OBD II code P1537/38, P0171 and P0420


It could all be related.P1537/38 are the intake manifold runner controls are stuck open.They are controlled by vacuum solenoids.The P0171 is bank one of the engine is running lean,usually caused by a vacuum leak, P0420 is catalytic converter ... 1996 Ford Windstar

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

Ford Windstar 1996 Trouble Codes P0171, P0141, P0161, and P0174


Mass Air Flow sensor. All four o2 sensor are not going to fail at once.I went through this for weeks trying to figure it out. I had just replaced the MAF sensor about 8 months prior, so I thought it must be something else. After throwing new inta ... 1996 Ford Windstar
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 6.5066 seconds