Having problems with your 1999 Chevrolet Silverado 1500 ?

Rebuilt engine 5.7 l 1998

\015 Engine starts easy timing checked 4 or 5 times , rev engine wil rev instantly will acelerate instantly b ut when you slow down to a stop engine stalls and hard to start then runs fine again \015\012Atfirst code p0341 would come up but now its not. \015\012Do I need a new crank sensor.\015
Posted / edited by AnonymousUser on : 15-01-2018

Answers :

I broke down and purchased a new crank shaft sensor . It cost $15000 hated to spend it because everbody told me they just don't fail , and why would it when it worked fine before the motor was rebuilt. IT FIXED IT.
\015\012
Repair Help & Product Troubleshooting for 1999 Chevrolet Silverado 1500

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

2002 2L SE A6. - Suffering speedo bounce. Recently had the engine rebuilt following dreaded water ingress into engine via brake servo. Now after about 30 mins driving in any conditions variable or motorway the speedo suddenly drops to zero recovers under braking. Then intermittently drops to zero or bounces and then sticks between 0 and 40 mph. Have disconnected battery for 30 mins but has not cured. Have had garage diagnostic check. This confirms fault. Have reset ECU but still no cure. Have th


Hello,Thanks for using FixYa.There are two possibilities why your speedometer would jump around.1. Faulty Speed Sensor (the usual cause)2. Faulty Speedometer (uncommon cause)What you need to do is to ha ... Audi A6

1987 Samurai idles fine. Above idle goes lean, runs rough, mc dwell 0. Rebuilt carb., no change. replaced with rebuilt carb., no change. Timing bounced around when engine running bad, replaced dist. w/rebuilt, no change. Replaced ECU with known good one, no change.


87 has no ECU. so must be an engine swap to a 89 or newer trackeror last sammi that did have EFI.you said EFI and Carb in same paragraph and that is a contradiction.post to my bbs for more help.http://www.fixkick.com/bbs/post ... 1988 Suzuki Samurai

1981 chevy 350/or 305?, it is a rebuilt engine, but when I set the timing at 0, 2,4,6,or 8 degrees it sounds good, however, when it warms up it won't start without moving the distributor. I checked the rockers on #1 cylnder at tdc. They are both closed. When I advance the distributor the car starts when hot, but doesn't have power. I am at a lost. I am thinking that it might be the ignition module, or ignition coil. Is there a way to tell? The engine is in a 1981 Caprice Classic and don't reall


Is your heat riser siezed? If it is siezed closed you have too much back pressure. You will need to free it up. To do this you may have to take the exhaust manifold off as it is situated in it. Use heat & WD40 to free it up. Good luck! ... Chevrolet Caprice Classic

I have a 2002 VW TDI with 140,000 miles, but engine was rebuilt after broken timing belt, and trans was replaced under warranty at 98,000 miles. My problem is that the engine cranks eight or nine times when starting next morning, even though car is parked in indoor and heated garage. All services have been performed right on time and I use nothing but MOBIL 0-40 OIL and high quality oil filters, etc, etc. It has a new timing belt (the newer type which came out in 2003) Glow plugs are all okay a


Hello, I have something that might help you. If you know where your fuel line goes into the engine. I would let it sit overnight and then take the line loose. Then hold the fuel line into a bucket and have someone turn on the key in the car. This sho ... 2003 Volkswagen Jetta TDI

A6 2L SE 2002. Recently had engine rebuilt following dreaded water into inlet manifold! Car back but now have some erratic speedo bounce. Starts after about 30 mins driving irrespective of the conditions. Speedo drops to 0 on acceleration returns to normal on braking but then intermittent drops back to zero or bounces from between 10 and 40. Have disconnected battery for 30mins to reset ECU. Have taken back to garage who have put on diagnostic which confirms but still occuring. Have thought abou


Sounds like to me you have a wiring harness problem ... 2002 Audi A6

I rebuilt my engine on my 99 grand cherokee can i rest the miles to 0?


Sorry the answer is no, you must not tamper with the mileage,the mileage is on the vehicle not the engine, ... 2001 Jeep Grand Cherokee

S10 1999 bearings bad 0 oil pressure,removed and rebuilt engine, replaced most all. back in and...Won't start, not a crank or a ticking from the starter. Starter and starter selanoid, battery all tested OK.conecting to starter and starter getting power. Replaced neutral safety switch twice , check all 3 relays all OK. Still no response. Lights and accessory lights all go on when ignition turned. Have tried all gears but still nothing. Could I have forgotten to replace something. Is there a way t


Yes, you can hotwire the starter, use a button starter to energize the solenoid. there is a chance thet the new or rebuilt starter isn't working. it has happened to me I went an bought a newly rebuilt starter but it was no good, it happens sometimes. ... 1999 Chevrolet S-10 Pickup

I have a 2000 dodge caravan with a 3,0 ltr engine. The auto has 250 + miles and I have had the transmission rebuilt. However, the trany is beginning to slip, primarily i=when the motor is cold and when down shifting at lights, stops etc. Is the a fileter to be changed/ cleaned or is my problem more serious? Fluid looks and smells good and is at proper level...


Could be the torque converter ... 2000 Dodge Caravan

03 gmc envoy with 5.3 140000 miles. Oil pressure reading fluxuates between 0 and 40. When problem first started pressure read 80. When vehicle was new it stayed at midpoint (40) vehicle has plenty of oil. if you rev engine or increase rpms it goes to 0 and stayes there. let off and it jumps around like it did when started (0 to 40). No engine pecks while running. Display indicates low oil pressure and stop engine. orange light (check gages) comes on when at 0. any ideas. Service engine has not c


There may be a loose wire or the gauge or sending unit may be going bad. The first thing I would do is to hook up a temporary oil pressure gauge, not using the old one at all. With this watch gauge while driving and see what readings you get. If the ... 2003 GMC Envoy Xl

Rebuilt top half of engine and rebuilt transmission. Car revs to about 3000 RPMS when accelerating. The car will then slip into gear and run smooth. Transmission guys claim it is a problem with the motor. The car never reved high after the engine repairs until the transmission was rebuilt. Is the problem in the engine or transmission?


Sounds like the trans is slipping. ... 2001 Dodge Intrepid

I have a Toyota tercel 92 with 120 000 miles on a rebuilt engine (225 000 miles total). When I turn the key, not every single time but most of the time, I hear a single, hard clunk. Also when I engaged the engine in first gear the speedometer needle doesn't move until the engine reaches 5-10 mph. This is accompanied with a noise that sounds like gear slipping. I was told that the starter assembly is the problem and to change it for a rebuilt one. Will a rebuilt starter be reliable? Is this a


Replacing the starter is one of the easiest things to do. Just unhook the battery first so you dont pop a fuse when you unhook the cable from the starter. Rebuilt starters are the norm. Noone buys new ones unless you have deep pockets. You only h ... 1992 Toyota Tercel

Ford Focus engine diagram Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V


... 2001 Ford Focus

Hyundai sonata 2000 gls. v6. HAs no EGR. Emission test, first try, HC(0) CO (0) nox 1033 mechanic said my engine seems hot (there was also heat out of vents blowing out. I cleaned my maf sensor and put on high octane gas and fuel cleaner drove for a week and retested. ssecond try HC(0) CO (0) nox 1250. failed agian. I changed my mass airflow from anotehr car and change my 3 front spark plugs myself not the three at back. Car seemed to be running better and engine definitely cooler no mor


... 2000 Hyundai Sonata

1988 Plymouth Grand Voyager cutting out. On and off since the 1990's. In 2007 I bought a rebuilt engine to replace original engine. This did not solve problem. So I know the problem lies somewhere between the intake manifold (which I had to keep from the old engine for the rebuilt engine)and the wiring, computer module, etc. Sometimes it goes away for a spell and comes back. Looking for simular story from anyone who was able to find a solution. Todays date is July 11, 2009.


If it's similar to my 96 Voyager it restarts after just a few seconds and seems fine. Cut outs are completely random as to frequency and driving conditions. In my voyager the solution was embarassingly simple. I had bought the car used with 172000 ... 1996 Plymouth Voyager

91 Corvette - Service Engine lights, Speedometer goes (usually) to 0, Average miles per gal goes to 5Y5, engine stops. Engine cranks but will not start. Wait a bit, remove key, insert key and it will usually start. only code is 12 which is normal. (Speedometer sometimes goes to 108 or 17 instead of 0 - while sitting and Idleing) Can sometimes get out of engine stopping by flooring it - must be driving to do this.


... 1991 Chevrolet Corvette

My brothers and i just rebuilt our engine she tuned over and sounded great. the next day we started it again it was idling low i had to give a little gas till it warmed up but the check engine light went on two days ago i used my scan tool and it said it was the ect, circuit high, we replaced all the sensors in the engine when we rebuilt..also my headlights wont go off unless i shut the truck down now and if the hazards are on and i step on the breaks the hazards stop why is this short happening


Ect high circuit means that the computer thinks the connector is unhooked. If it isn't then you need to check the wire for a 5v signal.\015\012\015\012Not knowing what year truck were talking about I will assume you have a 2 wire sensor. ... Chevrolet Silverado 3500

Timing Belt My car has a rebuilt engine and only has about 150,000 on the new engine. My question is what should i do about getting the timing belt fixed before it goes out. Or does it get changed when the engine gets rebuilt?


IT should have been changed when the engine was rebuilt. You change them out every 105,000 miles so I would call the place that rebuilt your engine and ask them if they replaced the timing belt or look on your receipt. But when you rebuild a engine t ... 1996 Honda Accord

2000 saab 9-5 rebuilt trani,rebuilt engine, rebuilt turbo,new head gasket, engine light still on and leaking oil


It will be like new,great. ... 2000 Saab 9-5

Ignition When I turn on the ignition I drive a few feet and when I stop the rpms goes down to 0 and the engine turns off, some times it turns on but the rpms go down to 0 without driving and the engine turns off. No check engine light is on.


Check your fuel filter and fuel pump. ... 2000 Mitsubishi Montero Sport

I just put a rebuilt engine in my 92 wrangler, and had the trany rebuilt. the engine runs and you can drive the jeep. the problem is the speedomiter does not work and if slowing down for a stoplight as the rpm comes down when you put it in neutral it does not stableize at idle, it drops till the engine stalls. the electronic speed sensor and camshaft indicator have been replaced.


... Jeep Wrangler

Where can I obtain a new or used engine for a 98 ford expedition. I believe the engine has locked and will need to be replaced or be rebuilt. Can you give me an estimate on both rebuilt and new prices for the vehicles engine and a possible solution as to where the vehicle should be taken. The vehicle is in Nashville TN.


... 1998 Ford Expedition

1994 F350 7.5 Dually 2wd I replaced the master cylider with a rebuilt. New rear hubs and shoes. I have bled the systen 2 separate times per repair manual. There is no brake fluid leaking any where. Problem is when engine is started brakes are spongy and will go to floor. With engine off the pedal will pump up and feel normal soon as you start engine pedal goes to floor. Could the rebuilt master be bad?


I have the same problem,, put all new brake components on truck, needed it anyway,, found out that the booster is not designed for a diesel application,, ford made a model change for the diesel,, number from ford is F 5 T Z - 2005 CA a ze ... 1994 Ford F350 Crew Cab

Engine code 12; installed new rebuilt 3.0 engine in 1988 dodge Caravan (same engine that was in van). engine light and maintenance light will not go out. We have put well over 1,000 miles on new eng


The maintenance required light is a reminder to have the vehicle's emissions systems checked and then be reset using Chrysler's DRBII scanner. It will not go off on its own and has nothing to do with your problem. Code 12 means that the logic module ... 1988 Dodge Caravan

98 buick lesabre oil pressure dropped to 0 and engine died. added 1 quart oil, waited 30 minutes, started and drove 5 miles then oil pressure dropped to 0 and engine died. does this sound like a bad oil pump? where is the oil pump and is it hard to change for a "handy" person? thank you.


My sister had the same problem. There are 2 sensors that can cause this when they go bad. One is the oil pressure switch, which is located near the oil filter. When the PCM reads this switch, and gets a low reading, it will automatically kill the eng ... 1998 Buick LeSabre
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.5679 seconds