Having problems with your 1999 Chevrolet K2500 ?

How do i change my lower ball joints on my 1999 k2500

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1999 Chevrolet K2500

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i change my lower ball joints on my 1999 k2500


... 1999 Chevrolet K2500

I have a 1994 Ford Bronco Xlt with a 302 V8 Automatic.. When the truck was on a lift the front passenger side wheel had alot of negative camber I believe.. The wheel was slanted like this . The stearing wheel is on a slant when the truck is going straight, and when taking off the front end shakes alot.. I believe it is the ball joints.. My question is how do I change all ball joints? Or detwrmine if it is just upper ball joints or lower.. Also while changing them should the steering wheel be s


To check the joints jack the wheel off the ground by the lower control arm and putting one hand on the top of the wheel and the other on the bottom try moving the wheel in and out. If you can then one or both ball joints are bad. Have someone move th ... Cars & Trucks

When changing the upper an lower ball joints do i really need to change the control arm or can i just change the ball joint


Its all one peice ... 1999 Ford Expedition

How to change lower ball joint on 95 mercury cougar...do you have to take lower countrol arm off to get ball joint out?


I would replace the whole control arm because the bushing are probably worn out too and it's easier than pressing out the ball joints. make sure you have a spring compressor tool when you do this or you could get seriously injured ... 1995 Mercury Cougar

Diagram to change out the lower ball joints in a 97 mercury mountaineer I was told by the machanic that my lower ball joint on the left front side needs to be replaced. My truck is making a buking noise like something is lose. I am trying to do this my self so I need a diagram to help me do this job. Please help!!!


... 1997 Mercury Mountaineer

I just worked on a 2008 Hyundai sonata with bad front suspention,I've change d shock absorber,complete upper arm,stabiliser linkage bush,lower arm ball joint,lower arm bush,yet I still ear dis noise like the ball joint is bad.any help to resolve this issue?


Did you change the upper arm ball joint. It has no load and if loose will be noisy. ... Cars & Trucks

The lower ball joint assembly has a four riveted and not bolted how do i change my lower ball joints


You have to drill out rivets and use bolts to install new ball joint. (some new parts come with bolts just for this instance) ... Dodge Ram 1500

2000 mountaineer i know the upper and lower ball joints are bad also the sway bar links.can i change just the ball joints or do i have to change the whole control arm with them Thanks Rob


Try Autozone or Oreillys for the parts. If they list them you can do just the ball joints. I had the same story with my 2002 Mercury. The dealer parts guys told me the "A" arms were 1 piece with the joint; yet the shop manager in the same dealersh ... 2000 Mercury Mountaineer

How hard is it to change the ball joints on 89 f250 4x4 does the ball joints press in or have clios and what basic tools do i need and what is the time to change both sides upper and lower


It's a bit of a job especially if you live in the north where road salt is a factor. You have to remove the brake calipers, then lock-out, then the hub, (special tool required). Then the spindle, which is usually rusted in and can be a bugger. Discon ... 1989 Ford F 250

I need to change the upper and lower ball joints on a 2002 dodge ram 3500 4x4. i am having problems geting the hub off and can not figure it out. I have the tie rod end out rotor and eerything else is off. I was told to remove the top ball joint but do not have a ball joint press.


... Cars & Trucks

I have to replace the Upper & Lower Ball-Joints on my '03 5.9L V-8 Durango, do i have to also change the control arm or can i do only the ball joints?


By control arms i think you mean tie rods whether inner or outer you should check them and if no slack,then just change the balljoints. ... 2003 Dodge Durango

Can you change upper and lower ball joints on 1999 ford ranger without changing upper and lower control arms?


Yes. ... 2000 Ford Focus

95 ford escort I replaced lower ball joints and tie rod ends now my car is riding rough over the road feels like tire going to fall off. It never did this before until i change the tie rods and ball joints. I'm very confused. Thanks plz help...


Take it back to the place which did the work and ask them to figure out where they went wrong. if you did the work, take it to a shop and ask them to align it and tell you what else you should have replaced. i assume the struts and strut mounts were ... 1995 Ford Escort

How to change lower ball joint on 1993 caravan.


Very simple...I don't have my Chilton's in front of me but I can tell you the easiest way to know is to look UNDER the ball joint. If you don't see screws or rivits....it is pressed in. Looking at replacement parts....it is pressed.\015\012 ... 1993 Dodge Caravan

Changing lower and upper ball joints


Go buy a chilton's manual from the parts store. Has diagrams and written instructions. ... 2004 Dodge Ram 1500

How hard is it to change the lower ball joints on a 2000 nissan xterra


... 2000 Nissan Xterra

How do i change the upper and lower ball joints on


The upper and lower ball joints are riveted in on the oem ball joints you have to cut the rivets and then use a balljoint press to press them out the new ball joints have nuts and bolts just press them back in and tighten down the nut ... 2000 Dodge Ram 1500 Truck

How to change a lower ball joint on a 99 chevy


... 1999 Chevrolet Silverado 1500

How to change upper and lower ball joints for dodge dakota 03 4X4


... Cars & Trucks

Changing lower ball joints on nissan tarreno 1991


... 1992 Nissan Pathfinder

How do you change upper and lower ball joints on 2001 Ford Expedition?


I am not going to lie to you on this. if you do not have a very good mechanical back ground you should not attemp this procedure your self because it could result in serious injury. it should be brought to a shop because they do have the right tools ... Ford Expedition

Removing lower ball joint on 1996 gmc K2500 4wd


... 1997 Dodge Stratus

I have a 1999 camry LE which is making a knocking noise on both sides(more on the right side) at the front like if the struts/ball joints are bad; I changed the both struts, ball joints and the noise is still there; I purchased the upper and lower tie rods today as my last attempt to solve this problem; any help would be appreciated;


The outer tie rod ends can make a clanging noise if they are loose. You can easily check them - grab a hold of the tie rod and try to move it around to see if it has any play in the steering knuckle.. The noise could also be caused by the ... 1999 Toyota Camry

Changing CV Joint axles on both sides of my 4x4. Do I have too drop the lower ball joint or is their another way around this? thank you


You will have to unbolt them. But Check them first. They are likely loose . Blazers are hard on lower ball-joints and it will be a good time to change them at the same time if they are bad. ... 1999 GMC Jimmy

I have a 1999 Ford Explorer XLT, 2 wheel drive,4.0 V-6. I have had this annoying knock from the front end when you drive over small bumps. As time has went by, I have changed the following because they needed to be changed, not because I was trying to cure the knock. Upper Control Arms, Lower Ball Joints, Tie Rod Ends, inner and outer, Anti-Sway bar end connectors. Actually found one of those broken, thought that was the knock, but wasn't. And just recently, replaced the front anti-sway bar bush


Front shocks? Make sure battery is secured . ... 1999 Ford Explorer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.4729 seconds