Having problems with your 1998 Toyota RAV4 ?

I have a 1999 Rav 4 2.0 l has spark and fuel to cylinders,yet still wont start.Possible Crank Position Sensor?Help Please.Thx.

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 1998 Toyota RAV4

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1999 Rav 4 2.0 l has spark and fuel to cylinders,yet still wont start.Possible Crank Position Sensor?Help Please.Thx.


... 1998 Toyota RAV4

I HAVE A 2000 SC MODEL SATURN. IT IS THROWING TWO CODES 107 LOW MAPSENSOR VOLTAGE AND 300 RANDOM MISFIRE CODE . THE CAR WONT RUN. THE FUEL PUMP ISNT RUNNING I JUMPED OUT THE OLD PUMP AND IT RAN BUT I DECIDED TO REPLACE IT AND ASSOCIATED FILTERS. IT STILL WONT RUN I HAVE CHECKED FOR VOLTAGE AT THE PUMP PLUG AND I HAVE IT IN THE ON POSITION FOR 2-3 SECONDS AND I HAVE IT WHILE CRANKING BUT THE PUMP STILL DOSENT RUN I CHECKED THPLUG PINS, SWAPPED OUT THE FUEL PUMP RELAY AND CHECKED THE 10AMP FUSE I


Have you checked for fuel at the engine and also at the cylinders? If your getting voltage to a nw pump while cranking the starter, there's no reason why it shouldn't be moving fuel. Disconnect the ... Saturn SC1

Hi i drove my car this morning and when i got back i listened to the radio a while with the car in the start position but not cranked. now when i try to crank my car it is not making any noise and it will not crank...i dont know whats wrong ive tried to get a jump but it still wont crank...could you please help


Dead Battery?\015\012Bad Starter ... 2004 Ford Taurus

2002 chevy malibu 3100 v6 83,000m, still has no start condition after crank position sensor behind balancer and cam sensor were replaced. fuel pressure is 56 even while cranking and does not leak back after key is off for quite some time(15 min. or more). No engine light on in cluster, has spark to all cylinders. Starts with ether but wont stay running, sometimes while cranking sounds like it wants to start but then does not and makes a backfire type of noise


I think your problem is injectors not firing, and is linked to the Powertrain Control Module. Disconnect the battery for 30 minutes to reset the PCM. Reconnect the battery and try to start the car. ... Chevrolet Malibu

2002 audi a4 would not crank when you attemted to start. I removed crank position sensor and cleaned it and now engine turns over but still wont start. I assume this indicated the sensor is not operating correctly. any ideas


... Cars & Trucks

I have a 2000 dodge durango that wont start. I changed the crank shaft senser and the cam shaft position senser and the cap and rotor button but still wont start


Have you checked for your DTC code?? The code may help you address the issue that is keeping your engine from starting. ON-BOARD DIAGNOSTICS \015\012 \015\012 1. Cycle the ignition key ON-OFF-ON-OFF-ON within 5 seconds ... 2000 Dodge Durango

My 98 dodge durango 5.9L for a while would only start on the second try but would still crank over and start. not it wont even try to crank and the battery is fully charged then u hear clicking from the passenger side and from the fues box in the engin compartment and the lights,horn,door locks, and radio dont work and make clicking noises when u try to use them. i have tryed to put the key to the on position and wait for ten or15 seconds and this does not work please help


Hey dude I had the same problem. Check your power terminal it could have junk on it that's what's causing it not to have power an start. Also to hear if your starter is good use jumper cables an connect the power straight to the fuse box power termin ... 1999 Dodge Durango

1992 dodge 318 engine turns over, but no start. No spark present. Replaced ignition coil and pickup coil, still no spark. 1992 dodge ram 150 full size truck 318 engine. starts sometimes then wont start just cranks ive tried a coil and pick up coil and now they said it might be a crank position sensor .


If truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10 ... 1992 Dodge Ram 150 Club Cab

Engine cranks over but no fuel being pumped plus no power to fuel pump. No spark to the spark plug. I put new crank positioning sensor, new cam sensor, changed computer, checked fuel pump relays. Car still wont start.


Check the main relay and fuse. ... 2001 Nissan Sentra

H my name is carl my 2002 Hyundai accent will crank over everything comes on but wont start there's no spark,and no power to fuel pump and i changed the crank shaft position sensor and still nothi


Have you checked the timing belt, it is most likely has stripped out teeth and not turning the camshaft(s). Pull the belt cover off the front of the engine and see if the camshaft pulleys rotate when cranking the engine over. ... 2002 Hyundai Accent

96 chevy cavalier 2.2 turns over but wont start have changed the following: fuel pump fuel filter map sensor crank shaft position sensor ignition module ignition coils plugs wires ran a ground from ignition module. It still wont start I need to get it going. I need ideas on what it could be


... 1996 Chevrolet Cavalier

I let my friend borrow my car. He let it sit for a month or two (Winter months) and now it wont start.. I've replaced the battery and the spark plugs. The engine cranks and has started only twice for me. The last time it started it stayed running for about 2 minutes. it was running well at a normal idle... and then all of a sudden stalled. The stall was like someone had turned the keyt in the off position. I check the key and it was still in the runn position. The "message center" in the dash ha


Sounds to me the fuel pump has went south on you but first I would change the fuel filter ... 2000 Jaguar S-Type

Everything has power when i turn the key to the on position but when i turn the key to start the truck, nothing happens. headlights dont dim or anything and everything still has power. all fuses are good. I have put 2 new starters on it and neither starter fixed the problem. Put a new neutral safety switch and a new ignition switch on it and it still wont crank or move at all. It starts no problem when i push it and kick start it. 1993 isuzu rodeo, V6, 4 wheel drive, 202K miles, standard tr


Have a look at this: http://www.fixya.com/cars/r5605161-trouble_shooting_isuzu_starter ... 1993 Isuzu Rodeo

1996 jeep cherokee strait 6 wont crank in the mornings and sometimes at all.when driving it will start to cut out and backfire.I've changed crank position sensor 2 times,plugs, wires,distributor,ignition coil and still have the same problem for about 2 years.mechanic put a new pick up coil in distributor and ran great for a day like it does sometimes.next morning it wouldn't crank.mechanic said he did not know what the problem was!the code it shows is a code 43.Which means a multiple misfire in


The 'backfire tells me the ignition has ceased to work for a short period of time and uburnt fuel has accumulated in the muffler to ignite when the ignition works again.. That indicates an intermittant fault in the ignition wiring, and of course like ... 1996 Jeep Grand Cherokee

I replaced the crank position sensor on my eclipse gsx but the car still wont start it turns over n ***** but it wont start i replaced almost everything i could think of to make it start n no luck


The\012following are the general instructions on the start of diagnosing any\012electronically controlled engine or transmission problem.\012The\012engine and the automatic transmission (transmission control is only\012for automa ... 1995 Mitsubishi Eclipse

I have a 2003 chrysler sebring convertible 2.7 the engine lite went on and the diagnostic said crank shaft position sensor the one i removed was worn so i put in a new one but the car still wont start what could be the problem?


Do you have spark?Just because you have the code doesnt mean its the solution,check you spark remeber the crank sensor signal is at the transmission and the cam is at the cylinder head,is the flywheel broken? is the cam and crank synchronized?check f ... Cars & Trucks

I have a 1999 ford escort 2.0 DOHC and it will crank but wont start...it had a new fuel pump put in it and ive put a cam position sensor on it and a battery..its gettin fire and its blue spark but still no start..checked compression and all cylinders read 80 to 90 psi..idk what the compression is supposed to be but it seemed low... If anyone knows somthing that i dont please let me know..email me at [email protected]


... Cars & Trucks

I have a 1999 ford escort the will crank but not start..new fuel pump new battery..replaced cam position sensor and checked to see if it was firing and it was and it was blue fire witch is good..i even spratef ether and still wont stary..did compression test and all cylinders are around 85 psi...dont know wht it is supposed to be but it seemed low...im stuck and need answers and correct ones at that..if anyone can help me plz let me know...thank u.. U can answer here or email me at brandonjames0


Have you checked the fuel filter? Sometimes if the catalytic converter is plugged up the engine will not run. In some cases the material in the converter can break loose and plug up your exhaust pipe or the muffler. This happened to my sister-in-laws ... Cars & Trucks

Car has good battery but wont turn over last time it happenen it was the wire on the key cylinder checked it and it looks good also did dionostic and it sad crank shaft positioning sensor i thank it should still turn over


IF CRANKSENSOR IS BAD THE CAR WONT START IT CONTROL SPARK AND TIMING.CAMSHAFT POSITION SENSOR CONTROL FUEL INJECTORS TIMING.IF CAR WONT TURN OVER BATTERY CABLES OR STARTER IS BAD. ... 1994 Buick LeSabre

Jeep wont start was driving and it was just like you shut the key off now it will crank but is getting no spark i changed the crankshaft position sensor and still nothing any suggestions?


Did the timing chain break? do you have 12 volts to the coil?is the coil bad? r u sure your not getting spark? ... 1994 Jeep Wrangler

Changed fuel pump and crank shaft position sensor. still turns over but wont start


Is there compression int he cylinders? pull a plug and put your finger in the hole, and have someone try to crank the engine. If the engine does not make any pressure then you will be looking at valve timing problems. If you need more detailed he ... 2004 Kia Optima

Changed the head gasket and timing belt on a 96 with 2.5 l doc. now it wont start. seems to be a timing issue, I can't see my timing mark with the timing light. Re aligned timing belt three times and am sure it's correct, still doesn't run. compression is between 170 to 182 psi. Cams are in the correct places, all the marks are lined up correctly. I Have fuel, and good spark. Resistence checked out on the crank and camshaft position sensors. I got continuity from them where the wiring ha


Remember that on a car's engine, the cams spin once for every revolution of the crank. It's possible that when you reassembled it, you put the distributor on 360 degrees out of phase. If you did so, the plugs would be firing on the exhaust stroke of ... Subaru Legacy

1992 Geo Tracker, wont start. Was running great,went into store , came to start , turns over fine , no go . had towed home . checked spark , (lots) Changed fuel filter , no start . There is a constant clicking at the fuel pump relay , so changed that still the same . This clicking is occuring when ignition is in the on position , not while cranking. It appears the fuel pump is working .Its EFI equipped .


Makeminelgd,Did you find a solution to your problem? I have the same problem with my 9 ... Geo Tracker

Idle up and down.. have changed 0-2 sensors and mass air flow andthrotle position sensor but still has problem and wont pass inspection.. said cat converter not ready


Sounds like the IAC (idle air control valve) or possibly a vaccum leak. As far as the cat. converter not ready, the vehicle must be driven a certain distance or go through a certain amount of drive cycles for all the systems to be monitered. Most of ... 2001 Toyota Tacoma

99 chevy tahoe 5.7 wont fire up turns over but no go, has fuel and spark just replaced crank position sensor still nothing.


... 1999 Chevrolet Tahoe
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.6452 seconds