Having problems with your 1998 Ford Taurus ?

Which cylinder is #1 on a 1999 tarus?

\015 Which cylinder is #1 and so on?\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

In this vehicle from the front of the motor(facing water pump) your left side (or back bank) 1st cylinder is no 1 then 2,3,right bank or front 1st one is 4 then 5,6
Repair Help & Product Troubleshooting for 1998 Ford Taurus

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fitting 0-320 cylinders on 0-290 lycoming


\012You may have this\012posted in the wrong product category. Please select another category\012appropriate to the problem and re-post the problem so the correct\012expert will see and respond to the question.. \012\012This is for ... Cars & Trucks

1999 3.1l malibu after doing valve job the #5 cylinder reads 0 compression and the #1 compression reads 30. All of the cylinders specs are normal


Check the timing marks from your crankshaft. And then on your camshafts ... Chevrolet Malibu

Honda stream 2.0L ivtec (same as civic type r) jumped the timing checked compression 200psi in all cylinders stripped and found faulty oil pressure tensioner replaced set up timing and rebuilt and started running perfect stopped and fit covers and wheel and tried to start turning over but not starting (turning over very fast) checked compression 0 on all cylinders stripped and aligned timing marks and checked chain tension all good


... 2003 Honda Stream

2005 Isuzu Ascender: white smoke from exhaust on start up. Runs for 5-10 minutes and oil pressure drops to 0. Drives for 5-10 minutes, oil pressure drops and car shuts off. We have had nothing but major issues with this vehicle since we purchased it brand new. First, cylinder 6 misfired - dealership replaced cylinder; next the transmission went (we have never towed with it, although it says we can) - dealer replaced transmission. Now this problem.


You might kill the engine because you run the engine with no oil pressure. need to strip the engine. might jammed all the bearing. ... 2005 Isuzu Ascender

2004 dodge ram 1500 5.7 hemi. misfire on multiple cylinders. repaced plugs, wires, and coils. still rough. did compression test to reveal cylinder 2 and 3 low. 2 at 60, 3 at 0-25. the rest are at 125 or so. rings or exhaust valve? any other suggestions?


Sounds like you need an engine my friend or a good mechanic to rebuild that one ... 2004 Dodge Ram 1500

I have replaced timing belt have checked the timing several times and i am not able to get it started and i checked cylinder compression and found that each cylinder only had about 0-25 lbs. compression


Sounds like bent valves or as a worse case scenario you have the CAM shift 180 degrees out. That timing mark will line up in the correct position and when it is 180 degrees out. If the original timing belt broke while the vehicle was running the mo ... 2001 Kia Sportage

Fitting o-320 cylinders on 0-290 lycoming


... Cars & Trucks

Mazda bt50 3,0 cylinder head torque settings


... Mazda BT50

Im not getting a spark in my cylinder 1 on my nissan 300zx and now im getting a mis fire and its also idleing in the middle of 1 and 0 what could it be please help


... 1993 Nissan 300ZX

Which cylinder is #1 on a 1999 tarus?


In this vehicle from the front of the motor(facing water pump) your left side (or back bank) 1st cylinder is no 1 then 2,3,right bank or front 1st one is 4 then 5,6 ... 1998 Ford Taurus

Cause of 0 compression cylinders 2&4 on ej20 forester gt


... Subaru Cars & Trucks

95 Jeep Cherokee 0 compression in #2 cylinder.


If you have a 0 reading from cylinder 2 that means there is no compression from it and you need an enfine rebuild.It seems that there had been damage to the engine.Have it hooked up to a computer and check diagnostic code.Overheating of an engine can ... 1995 Jeep Grand Cherokee

My wife called me today at work and told me that her 2001 mits galant 4 cylinder while she is at a stop the radio would go out and the rpm gauge would go almost to 0 but the car still runs and when she hits the gas to go the radio comes back on and the rpms go back where they should be and i have never heard of that before could someone give me some advise thanks


You will need to replace the alternator/and or battery because it is starting to fail. Your car is running off the battery and not being recharged so when the car accelerates it acts normal but at a stop sign it will loose power. The veh ... 2001 Mitsubishi Galant

My 93 jeep wrangler 4 cylinder temp gauge doesnt work right. when driving the gauge reads 0 when i step on the gas the gauge moves to the right temp. i have installed a new therm. new water pump new rad.new temp sen.and the gauge still works the same. I have been told the guage is working right. need help????


Depending on how fast, this happens, could be an air lock in cooling syste, or a bad head gasket, or head. does the gauge ever go too high? can you hear gurgling in the rad, and does it ever push out coolant? ... 1993 Jeep Wrangler

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

Ford laser 1989 automatic is not firing on number 3 cylinder has plenty of spark--also when we put car in gear the whole cars shudders and there is no power ----- help :0(


... 1989 Mazda 323

2001 HYUNDAI SANTE FE 2.7 V-6 NO START- SOUNDS LIKE NO COMPRESSION( SPINS WAY TO EASY) CHECKED COMPRESSION ON FRONT CYLINDERS 0 PS1 FRT 25 PSI MIDDLE 50 PSI REAR ASSUMED OUT OF TIME-PULLED FRONT COVER REAR CAM (CLOSEST TO FIREWALL) OFF ONE TOOTH ON CAM GEAR CRANK AND FRONT CAM IN TIME COULD THIS CAUSE LOSS OF COMPRESSION TO THAT EXTENT?


Yea, because what probaly happened is that, you dropped a cylinder or two...which means you probaly have bent valves..that's why your compression is way out of wack...I believe that engine is an interference engine..so when the timing became off, the ... Hyundai Santa Fe

I have my harmonic balancer set at 0 and the no. one cylinder is at top o. Where can i find no. wire going into the distrubeter? also i think the timing is off. what can i do to fixx these problems? THANKS


Take off the distributor cap and look at the rotor. with the engine set the way you have it, the rotor should either be pointing to the block or the right front headlight. (In the general direction).If it is pointing towards the engine turn the ... 2007 Jeep Scout

Looking for pinion gear set differential housing - gearbox All oil drained out from dried up seal. Year: 1987 Make: AUDI 4000S ID: wauzzz81zhao(0)15347 Body: 4 Door Cylinders: 4 CYL fueltype: gas Transmission: Automatic Front wheel drive


You can get it here:\015\012\015\012\015\012http://www.autopartsworld.com/audi_parts/4000/differentialpinionseal.htm ... Audi 4000

I pulled the #1 spark plug and put my finger over it and had someone turn the motor over until the pressure moved my finger. I then used a socket and moved it the rest of the way by hand until the mark on the pulley was lined up with tho 0. I put a straw inside the #1 cylinder to make sure the piston was at TDC and the piston was not near the top. I had someone hold the straw and turned the motor by hand and got the piston to the top and was pushing the straw out but now the mark on the pulley i


Yes it can be wrong is the crank in right it could be 180 degrees backwards i have seen it happen. but i dont know how much work was done before this problem email me some more info and i can help you further ... 1985 Chevrolet Chevy

Bought new procomp pc6al cdi box,has a dail on the end of box with letters a to f and 0 to 9 what does it do and what do I set it to.Also has has 4 switches on end of the box 1 to 4 at top it says on,what is it for and what do I set it at.I have a 4 cylinder air cooled vw bug engine.Can you also email instructionsor manual for the procomp pc6al box


Go to the Procomp Electronics website and they give instructions! ... Volkswagen Beetle

When driving my X type 2.1 (2002) it jolts and loses power in the 0 to 50mph range most when im driving uphill, when i drive over 70 it judders badly. It has been attched to a computor and comes up as fault in no3 cylinder. have changed the sensor on no3 spark plug and fitted new plugs but this does not seem to make much differance.


Try ur air duct sensor ... 2002 Jaguar X-Type

My 92 4runner has a engine shake and when you give it gas after 4 sec it knocks but its full of oil also i had a compression test done on it and they said the 1 and 2 cylinders had 0 psi


... 1992 Toyota 4Runner

What is the torque specs for the overhead camshafts bolts for a 2002 lexus es300 it is the camrey motor six cylinder 3,0 liter


... 2002 Lexus ES 300

Hi i have a question about car engine, i have a projekt im am building and for that i have a stock 130 hp 2 l 4 cylinder engine no mods or tuning done ion it its just stock, but if i want to have something like a nos effekt could i instead of nos use pressureized air , so if i have a small 20-30 l air tank on my "car" at maybe 10 Bar then requlate it down to 0,5 -1 bar and press it into the engines air intake then i should get + certain increase of horsepower for adleast a little while , i


It would have to be a high pressure tank to do you much good, 2000 to 3000 lbs pressure regulated down, it would be close to a nitros setup, you'll have to dial in the right manifold pressure,these setups are like a passing gear,top gear, pedal to th ... 1992 Saab 9000
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4451 seconds