Having problems with your 1998 Acura TL ?

1995 acura how do u set the vals and timming

\015 1995 acura how do u set the timming and vals\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

First you will need a service manual or information for this vehicle for the valve lash setting. The procedure is usually removing the valve cover( You will need a new valve cover gasket) putting the # 1 cylinder on top dead center and using wrench, screw driver or allen key,and a feeler gauge. You will need to follow the firing order when adjusting the valves. You will need a timing light to set the timing and also the timing spec. This usually involves warming engine to normal operating temp. clean harmonic balancer and mark the timing mark with some white paint loosen the the distributor hold down bolt hook up timing light and turn distributor until the timing mark on the balancer lines up with the timing mark on the timing cover then tighten the holding bolt back down. Also the timing advance has to be disabled when setting the timing and enabled when you are done. The valves should be set first then set the timing. A Haynes manual available at your local auto parts store should contain pictures and information to help you do this.
Repair Help & Product Troubleshooting for 1998 Acura TL

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1995 acura how do u set the vals and timming


First you will need a service manual or information for this vehicle for the valve lash setting. The procedure is usually removing the valve cover( You will need a new valve cover gasket) putting the # 1 cylinder on top dead center and using wrench, ... 1998 Acura TL

Ford ranger 2006 4,0 litre timming how to set


... Cars & Trucks

I CHANGED MY INTAKE GASKET ON MY 1994 GMC K1500 W/ 5.7 LITER.CHANGED CAP/ BUTTON, PLUGS,SINCE DOING THAT MY TRUCK RAN FINE THEN STARTED TO HOG UP AND STALL WHEN GIVING GAS.WE SET TIMING AT 0 DEGREES THINKING TIMING WAS OFF. IDLING IT UP RUNS BETTER. NOT SURE WHAT I COULD OF DONE INSTALLING INTAKE GASKET ?.COMPUTER ?, COULD YOU HELP ME OUT WITH THIS PROBLEM ? THANKS TIM FROM MAINE.


Hi Tim,\015\012 Please check that there is no leakage in your water cooling system. If there is leakage, it causes the engine to heat up and burnup the gasket. You need to make sure your thermostat is also reset properly depending on the wea ... 1994 GMC Sierra

Setting timming changed headgaskets timing marks up top set but bottom timming mark keeps movihg 15 deg btdc even know start at 5 deg rottor button set on number one but does not start . sounds like it is still out .have i set timming w rong


Put the engine at TDC compression stroke , Thats when the valves are\015\012both closed on No 1 cyl and the piston is on its compression stroke\015\012.then align all cam and crank marks. set distributor/rotor button on No 1 cylinder (rotor\015\012p ... Mitsubishi Passenger

I just replaced all timming chains, tensioners and guides on my 98 mercury mountaineer 4.0 v6. There are no timming marks to set the timming with. How do i set the timming ??? PLEASE HELP!!!


TIMMING IS NOT ADJUSTABLE. IT IS ALL COMPUTER CONTROLED. THE ONLY TIMMING IS THE MARKS ON THE CHAIN AND GEARS. ... 1998 Mercury Mountaineer

Setting up cam timming on head for 2002 hyundai accent 1.6 motor , when you replace the DOHC's i need to know about the set up of the timming chain and the timming belt and why the valves are not closing all the way ?


... 2002 Hyundai Accent

I have just purchased an Antler cabin bag with a TSA lock, should be preset to 0 0 0 as per factory setting & I should be able to open it, unfortunately this is not the case, any suggestions????


... Cars & Trucks

Ford ranger 2006 timming how to set


... Cars & Trucks

I have a opel astra 1.8ie 16v, I am currently changing a snapped timming belt, had to have the head redone, got the new head in but the problem is setting the timing, I made sure that the timing marks on the camshafts line up with the marks on the top cover and the crankshaft mark alligns with the mark in the bottom cover, then I put the belt on but when I turn the motor over by hand it still gets stuck like its hitting the valves, is there any way that I can set the timming manually without usi


... Cars & Trucks

How do you set timming on nissian sentra 2002 were do the mark go i took head off now need to set timming


1.8 motor, you didn't say ... Nissan Sentra

Is it possible to change the miles on a 1992 GMC Sierra (1500)? I just switched out the v6 with a new 305 and for personal preference I wouldn't mind setting the miles back to 0. Not selling the truck, I mean I could always write down it's current miles to know how many miles are on the engine but it would be nice to set to 0 since its a new engine.


No if you want one with 0 miles you will have to get a new one ... 1992 GMC Sierra

How do you pair a Verizon I phone with a 2008 Acura TSX? I am trying to set up my Bluetooth capabilites on my I Phone--I turned on the bluetooth, but the I phone stayed in the Searching mode for ten minutes. I did turn on my Hands free feature on my Acura, and said Set up, but nothing happended


... 2008 Acura TSX

Set timming how to set timming on 1994 gmc pick up with 5.7 motor


You will need a timing light for Hi energy ignition as well as standard socket set or wrenches. 1. get the engine up to operating temp. 2 shut off engine connect the timing light to the number one[1] spark plug wire at the spark plug end connect batt ... 1994 GMC Sierra

Need to know were the timming chain gear is located and how to line up dots to set timming


... 2001 Pontiac Sunfire

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


Timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times thi ... 2000 Daewoo Lanos

Setting timming marks 2004 nissan xterra v6 3.3L engine the timming belt is being replaced how do I align the timming marks


... 2000 Nissan Xterra

My blitz turbo timer calculates time fine and displays how long the car will continue running but when i turn the car off the time sets to 0 and turns the car off, it used to work fine but now i dont know whats wrong with it, i messed with a few settings and set the minimum tome to 30 seconds but the car will still turn off.


... 1997 Mitsubishi Galant

My 2007 Acura TL is having an air conditioning issue... The air is coming out cold from the two vents on the driver's side, but the air coming out of the passenger's side vents is very warm. The air on the passenger's side does not change in temp regardless of the temp the climate control is set at. I have tried the dual setting, the individual side setting, turning just the a/c on with and without the recirculation option. My TL has the navigation system--if this provides any relevence to the p


Navigation has no relevence at all. but what does is the vent system in the dash.there is a flap inside the vents under the dash it sounds like it is not moving on the passengers side. ... 2007 Acura TL Sedan New Cars

Cam timming marks to set up the timming chain and cam timming.


Should be a dimple or dot on each gear crank one points up cam one points straight down they should line up perfecly. ... Jeep CJ7

My cam shaft timming gear and my crank shaft timming gear dots line up and my harmonick balancer timming mark is on 0 which way should my rooter button face towards number 1 or towards rear of engine


The rotor should be pointing close to number 1, but keep in mind that the spark is actually supposed to happen before the piston gets to tdc so the rotor will be a little bit past the number 1 terminal when the crankshaft indicates that you're at tdc ... 1994 Chevrolet K1500

Installed a rebuilt cylinder head set timming to all data and mitchells timming book wont start blowing back threw intake


Sounds like your timing is out 180 degrees. Recheck by making sure #1 piston is on the compression stroke, then retime. ... 1998 Isuzu Rodeo

Timming belt broke on 92 accord,set cranke to tdc


Here is what I do know. If your Accord has the 2.2 Ltr engine, it is an interference engine, and you may be right, you could have bent valves, bad cam, ect.\015\012Otherwise I am giving you a link to check out.\015\012Please let me know i ... 1992 Honda Accord

Code 42 set on an '88 Camaro w TBI.Also very erratic idle, occasional backfire through exhaust,"jerky" on acceleration.Feels like a "miss" or skip.Base timing set at 0;2;4;6 all btdc with ESC bypass disconnected. No difference. Seems to idle slightly better with this bypass disconnected.Idles "crazy" after bypass reconnected.Ignition module checks good;good dist cap,rotor, coil,plug wires and plugs.New o2 sensor.Any thoughts? Is Knock Sensor associated with this code? Is EST associated with this


Listen to fuel pump w/ key on , if you hear a spraying sound, you may have a split hose in the tank ... 1994 Chevrolet C2500

If the timing mark on the crank shaft pulley is set at 0 would that be the same as taking off the crankshaft pully and setting the timing mark on the block


Yes. that is correct 0 = 0 ... 1990 Toyota Pickup

Bought new procomp pc6al cdi box,has a dail on the end of box with letters a to f and 0 to 9 what does it do and what do I set it to.Also has has 4 switches on end of the box 1 to 4 at top it says on,what is it for and what do I set it at.I have a 4 cylinder air cooled vw bug engine.Can you also email instructionsor manual for the procomp pc6al box


Go to the Procomp Electronics website and they give instructions! ... Volkswagen Beetle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 6.4011 seconds