Having problems with your 1997 Dodge Dakota ?

Replaced crank sensor, coil and coil pick up still no fire

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

You have any check engine light on the dash display? This measn fualt code stored in the PCM.

Also, I suggtes check your master \015\012fuses (underhood) this prevent the computer system from allowing not only spark, \015\012but any of the ignition systems to operate.

Keep us updated.
If you replaced the crank sensor and it will not start, then your truck needs what is referred to as a "CASE learn." This procedure can be performed at qualified garages and dealerships. What it does is correlates the actual crank position relative to it's sensor in degrees of rotation so that the proper timing of firing the spark plugs can be calculated by the engine computer.
Repair Help & Product Troubleshooting for 1997 Dodge Dakota

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Car was running well then just refused to start.Computer indicated throttle position sensor. Replaced that, then crank sensor, then cam position sensor. Then took car to a repair shop. They thought cam belt, all looked good. They then said wire to crank position sensor bad and replaced it. Car then started with miss fire. The repair shop then replaced all plug wires and plugs. car still miss fires, they then replaced the coil pack.Car still miss fires on passenger side cylinders. The car starts

Its possible there are multiple coil packs usually one for each bank or one for every two cylinders. Or check for a ignition control module ... 2004 Dodge Intrepid

Replaced crank sensor, coil and coil pick up still no fire

You have any check engine light on the dash display? This measn fualt code stored in the PCM.Also, I suggtes check your master \015\012fuses (underhood) this prevent the computer system from allowing not only spark, \015\012but any of the ... 1997 Dodge Dakota

I have a dual over head cam 97 neon.It is not firing, i changed the crank sensor,the coil,and still no fire. the relay was switched.no fire. The last time it run yesterday, it run horrible. Backfiring, sounded like it was running on 3 cylinders.Then would fire every now & then. Now wont fire at all. thats when i replaced crank sensor & coil..PLEASE HELP

Remove your valve cover and have someone try to crank it over while you watch the camshaft to see if it turns, your timing belt may have jumped a tooth ( causes bad running and back fire ) and then broke ... 1997 Dodge Neon

Replaced crank sensor, pick up coil,dis cap, button and still no fire

Check automatic shutdown relay to see if it is powering coil and injectors. ... 1999 Dodge Durango

Got a 2001 Chevy blazer 4.3L cranks but does not start. got 62 psi at the fuel rail, replaced plugs and wires, got good spark at coil, replacing car and rotor! if the cam sensor or crank senor are bad willi still have spark and fuel is there a way for me to check injectors? was gas on plugs when i changed them. sprayed either in plugs and still no fire. so I'm leaning toward spark issue and help would be greatly appreciated.

... 2001 Chevrolet Blazer


\012HelloThe\012Engine and Automatic Transmission (not applicable to manual\012transmissions) in this vehicles drive train are fully\012electronically controlled by a computer called the PCM and TCM (Power\012Train Control Module, ... 2004 Kia Sedona

I have replace coil ,crank sensor, cam sensor,disturber cap and rotor and still won"t fire

Did u check the engine control fuse ? its located in the engine compartment fuse box i do belive its a 30 ! if tha fuse is blown then u will get no fire ! it took me awhile to figure out this on my own and i did all the same things and all it was cau ... 1998 Dodge Ram 1500 4WD

1992 dodge 318 engine turns over, but no start. No spark present. Replaced ignition coil and pickup coil, still no spark. 1992 dodge ram 150 full size truck 318 engine. starts sometimes then wont start just cranks ive tried a coil and pick up coil and now they said it might be a crank position sensor .

If truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10 ... 1992 Dodge Ram 150 Club Cab

We have a 2001 t&c limited. wife drove to work one day and it kinda missed backed fired. would not start. picked up and brought home. found out it was not firing. will not fire yet. replaced plugs . then replaced crank sensor. still no fire. can u help ?

Sounds almost like an ignition coil problem. ... 2001 Chrysler Town & Country

Im having problems with my mitsubishi Eclipse 2.4l it cranks but won't fire up? We replaced a torn timing belt, and fuel pump, crank position sensor, coils, replaces some wires, and another replacement from the dealer, and it still won't start or turn on.

... 2003 Mitsubishi Eclipse Coupe

My 2004 chrysler town & country is not firing on #1 & #4 on coil pack. I replaced coil pack twice because i thought i had a bad one and it is still missing on those two cylinders. Both coils were new that i replaced. Im thinking its the pcm or crank sensor but the car starts and run.

... 2004 Chrysler Town & Country

I have a 95 Ford Explorer and have replaced the coil pack and crank sensor and its still not getting fire to the coil pack, but it cranks sometimes and sometimes it doesn't what could the problem be?

... Cars & Trucks

My 2000 lhs is rough running like crap! now it says system too rich (bank 2 ) and it started with random multible miss fires and number two miss fire i replaced all plugs checked all coils and cam sensor and crank sensor still runs the same im pissed help please????


89 jeep cherokee 4.0 cranks and gets fuel but no spark... CHANGED THE IGNITION MODULE AND THE COIL.... still no spark. I just replaced my crank sensor and still no spark and wont fire up? wtf?

If you can access a good engine control module (computer) replace it to your unit and try starting the engine again. ... 1989 Jeep Cherokee

1996 volkswagen golf has no spark,it is pulling a po341 code.i have replaced ignition coil,crank sensor ,sparkplug wires and rotor button,distibutor cap and still no fire to the plugs,timing is right on the ,i replaced the head and it ran perfect for 30 minutes and just shut itself off and found find it lost spark.Rechecked the timing and still ok.Can anyone help

Can sensor is bad according to the code,but still could be the crankshaft senor,it is one or the other,my guess,and it is just a guess,it is the crankshaft sensor. ... 1998 Volkswagen Jetta

2002 dodge ram 2500 360 auto 4x4 truck quit running towed home fired up no issues after sitting for about 4 hours pulled the codes said p340 for crank sensor p1391 for DTC runs currently but RPM's surge at low idle and wants to die rpms go from 500 to 1600 continuously. If I keep reved up at 3000 it is smooth, replaced crankshaft sensor, TPS , ignition coil, pick up coil in the distributor, plugs wires cap rotor, any suggestions ?

What fault codes did you receive on the engine computer scan test. ... Cars & Trucks

97 s10 2.2...have replaced the ignition module, both coil packs, computer, fuel pump, and both cam and crank shaft sensors. Fired at first when messing with the wires under the hood all the way on the drivers side, only twice, but didnt run. Has fired spraying starting fluid in the intake and trottle body, but again only twice . We hooked it up to a diagnostic aand it says its okay to drive, but we replaced the fuel pump anyway, and still nothing.....any ideas?

Make sure the the firing are in place. check cables for continuity especially the high tension cable. and must be well fix.check the connections of fuel pump and must be well grounded. ... Cars & Trucks

96 Jeep Grand cherokee Laredo was having problem not getting any power to test light for crank shaft sensor or coil or fuel pump and gauges not working, we replaced pcm and crankshaft sensor and cam sensor getting fire now to crankshaft sensor but no further. Everything still the same other than that. What could this be? Please if any knows help!

... 1996 Jeep Grand Cherokee

No Spark my 96 jeep country has no spark to the coils. I have replaced the crank position sensor, sparkplugs and wires. Distributor cap, rotor button and coil. It still has no fire to the coils.

The " FIRE" doesnt come to the coil from any of those things you have changed.......The "fire" comes from the coil TO those items!!!! Good luck, RC ... 1996 Jeep Cherokee Country

Have a 96 chevy pickup 4.3 liter..i have replaced coil, distributor,crank shaft sensor, ecm fuse, module..still wont crank. Sometimes in mornings it will fire right up go back in few hours wont crank.

... 1996 Chevrolet C1500

My 1995 dodge dakota 5.2 V8 will die on me while im driving it or while im at idel and once it dies it wont start back up again .. i check my spark on my coil and i dont got spark after it dies until i let it sit for a while ...I replaced the coil, wires, crank shaft sensor, the cap and roader, the plugs and the distributer pick up sensorand it still hasen't fix my problem... any ideas i think it might be my PCM/ECM

... 1995 Dodge Dakota

I have a 93 dodge Dakota 3.9 v6 that won't fire. Changed crank sensor, ignition coil, and pick up coil. Still no spark. Can hear the fuel pump working. I'm stumped. Could it be a computer problem? Would really appreciate any help. Thanks.

... Cars & Trucks

My 1996 jeep cherokee 5.2 will crank, but it willnot start. I have no fire coming out of the distibutor. I replaced the distibutor, rotor, ignition coil, spark plugs, crankshaft pisition sensor and still no fire someone please help.

Check Neutral Sasfety Switch, located top trans, its possible that mis-adjust there.Other possibility, Anti-Theft system activated... some THEFT warning on cluster?Hope this helps; also keep in mind that your feedback \012is important ... 1996 Jeep Grand Cherokee

I have 1994 jeep wrangler 4.0 inline 6 5 speed, no spark I tried replacing coil, pick up coil ,crank sensor, still nothin tried resettin ecu but the codes wont clear I think might be a bad ecu ?

HelloI see that you have replaced allot of parts that can cause this crank no start condition but you have not performed any fault code testing or at least you didn't mention you did. To obtain instructions on how to perform a OBD1 fault code tes ... 1994 Jeep Wrangler

I have a rodeo/isuzu 4ze1-a recently replaced the MAF sensor and ended up with no spark.. Power to coil and out but no power to distributer.. Replaced distributer and still no luck... All relays and fuses ok Fuel pressue is good No check engine light Engine cranks but won't fire....

You said your not getting spark..... double check that all of your plug wires are firmly attached ... you could possibly have a bad coil pack . ... 1995 Isuzu Rodeo
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3248 seconds