Having problems with your 1996 Toyota Corolla ?

Reset brake pad sensor light where is the location for the sensor

\015 Brake light on dashbord is on change front brakes and light is still on\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

The warning light is usually for low brake fluid or the parking brake is on.
Repair Help & Product Troubleshooting for 1996 Toyota Corolla

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Reset brake pad sensor light where is the location for the sensor


The warning light is usually for low brake fluid or the parking brake is on. ... 1996 Toyota Corolla

2002 buick century over heats unless ac is running. I changed antifreeze, thermostat, temperature sensor, coolant level sensor, and all hoses. Also coolant light won't come off even though its full. I also changed out front brake pads, rotors, calipers, hub assembly's, and axles along with rear brake shoes, brake drums, wheel cylinders, and hardware kits but brake light won't turn off. There is no problem with the master cylinder. Is there a way to reset the brake light? Just brakes did it befor


Sounds like the computer is not powering the fan relay when the engine reaches 220 degrees. You might want to jumper the temp sensor to see it it will trigger the relay. You may need a scanner to monitor the data signal from the temp sensor.As ... Cars & Trucks

I have a 2004 4 runner that the brake light on the dash came on since i have replaced the front and rear pads and topped off brake fluid on the vehicle. The brake light is still on where is the sensor located for this light? and is there any other reason this light is still on other than a faulty sensor?


Any air left in the system can cause a light on. If you ran the system completly dry while bleeding your brakes, that can also cause the light to be on. There is a level sensor in the mastercylinder, when the level gets so low it will illuminate the ... 2004 Toyota 4Runner

The location of the brake light sensor on a lexus rx300 1999 yr the brake lights will not come on when brake is pressed i changed the bulbs the brake switch and fuses so the brake light sensor is the only thing left but dont kno where its located


It's in the driver side of the luggage compartment, behind the panel that has the power outlet. You would need to remove the trim panel and follow the harness to get to it. Most of the time it's Gray color. ... 1999 Lexus RX 300

Brake warning light came on after changing rear break pads and brake fluid on 2006 Monte Carlo. Do the sensors have to be reset?


... 2006 Chevrolet Monte Carlo

I have just changed front brake pads and wear sensor on a mini cooper 57 plate but the brake light warning indicator is still on how do i reset this


... 2008 Mini Cooper Clubman

2005 BMW X5 How do I reset brake wear sensor? And the brake light is on. Just replaced rotors and pads


Turn the key to 'on' but do not start the car. The light will reset itself in about 45 seconds.\015\012\015\012\015\0121. Turn key forward until power comes on (just short of starting)2. Let sit for 2 mins.3. Turn off. ... BMW X5 Series

I have a VW touran diesel 1.9. Recently there was a brake pad warning light indicated on my dash board, so I took it to my closest gargae to check. They replaced two new brake discs and the brake pads. However, they could not find a way to reset the warning light. So even though it is fixed, the warning light is still on my dash board. Do you know if it can be reset without going to the dealer?


Nope,it has to go back to a dealer(the computer is too expensive for a diy mech)they will reset it IF GENUINE parts have been used, as sensors are inbuilt into the pads. ... Volkswagen Golf

I replaced the front pads on a VW JETTA 2.5 and the check pads light is on. How can I reset the check pads light? I had the brake pads replaced on an 05 VW Touareg and the "Check Brake Pads" warning light has not gone off yet. Please help


Use the VAGCOM software tool, or just disconnect & reconnect the battery, that will reset any existing faultcode in the ECU. ... 2005 Volkswagen Touareg

2 weeks after I had brake pads replaced ABS and TC light came on and it was found that a sensor connection was loose. Drove fine for 2 weeks and light came on again. Serviced aging and a new sensor placed. Came on again 2 weeks later, new rotars put on. Was fine for one week and now both lights are coming on again. Prior to the lights coming on I can feel a pulsation in the gas and brake pedal. Brakes work fine when ABS and TC lights are on.


Good chance that the ABS sensor need to be adjusted to the speed ring on the hub. it's a common thing that happens when the brakes has been service and the technician did not measure the gap between the sensor and speed ring on the hub. Clean the spe ... Chevrolet Equinox

2004 touareg check brake pad light on after pads and sensors replaced


... Cars & Trucks

MY 2002 AZTEC DOES A GRAB AND RELEASE ON THE BRAKES WHEN PRESSURE IS APPLIED TO THE BRAKE PEDDLE but not all of the time. AND THE ABS LIGHT IS NOT ON IN THE DASH BUT AFTER THE LIGHT COMES ON THE BRAKES WORK JUST FINE! "I HAVE REPLACED ALL OF THE PADS AND SHOES" SO IT SEEM TO ME THAT A SENSOR IS PROBABLY BAD! it also seems that the abs light comes on more often when the vehicle is going around a curve or when you are applying the brakes! I NEED TO KNOW HOW TO TEST THE WHEEL SENSORS WITH A MULTI-


You need to get a Haynes or Chilton's repair manual for those directions. Now as far as your problem is concerned it's not a sensor, it's a kinked brake line, bad Brake Compensator or bad Caliper. The compensator is the part that comes off the Brak ... 2004 Pontiac Aztek

My 2002 Cadillac Seville STS has electronic brake pad waer sensors. I had a message on the dash reading "change Brake Pads" So I did. The mechanic said he had to replace 2 sensors. The message is still there. I also intermittantly get the abs, TC and BRAKE light on the dash, then they go off when it says "change brake pads". My question is. Do you think the 2 problems are related? Steve


... 2002 Cadillac Seville

In my Land Rover Discovery 2000, the ABS, traction control and hill descent warning lights come on when sometimes on brake application other times no apparent reason when driving and then reset and behave normally when engine is stopped and restarted. Any Solution to this problem? Also where are the ABS and Traction Control sensors located?


You've got a bad wheel speed sensor or corresponding tone ring. take it to a dealer. they'll hook it up to a computer and tell you which sensor or tone ring it is and give you an estimate. you only pay for the hour of diag. ... 1999 Land Rover Discovery

Reset brake pad sensor light - Land Rover Cars & Trucks


... Land Rover Cars & Trucks

How do I RESET BRAKE LIGHT ON 2006 BMW 325I.Brake pads and sensor already replaced


That has to be done by a dealership with a BMW specifiic scan tool ... BMW 325

Reset brake pad sensor light - Peugeot Cars & Trucks


... Peugeot Cars & Trucks

How to reset brake pad sensor light 2002 vw beetle


... Cars & Trucks

The Brake Pad replacement light is on, i have replaced all the pads and the wear sensors. and the light on the dash is still on. Is there any thing else i have to check? i have not checked the E-brake shoes(Do they have a wear sensor on it?)


Ensure all of your connections are good some vehicles have right and left pads but double check your connection make sure your wiring is not rubbing against anything ... 1999 BMW 323 Series

How to reset a brake pad sensor light on a vw sharan


... 2005 Volkswagen Sharan 1.9

How do you reset the Service light on a Mercedes CLC 180 Kompressor Sport - Just done a full service myself as a partially trained mechanic but cannot find the manual reset and don't want to pay a garage for resetting a silly light, also changed the brakes and the sensors but brake light still on :-(


I will need to know the year make and model of this car, as far as the brake light if the sensors are new then close all doors and trun the key on without starting the car and wait about 15 seconds and the brake pad warning light will go out, send me ... Mercedes-Benz CL-Class

The ABS, Traction Control and Brake Warning Lights came on in my 2003 Cadillac CTS. I took it to a mechinac who turned the rotors and replaced the pads. The lights came back on but the brakes seem perfect. The mechanic did not know how to reset these warning lights. Do the lights mean there may be another problem or do they need to be manually reset and, if so, how do I do it.


Lights usaly come on when there is a system fault. check for a broken or chiped wheel speed sensor ring, or a damaged wheel speed sensor. try disconecting the negative battery terminal for a few seconds to reset lights ... 2003 Cadillac CTS

Mini Cooper 2004 Brake Pad Warning Light Reset


One method describes just turning the key to position 2 and giving it about 30 seconds and that it will reset on its own. A manual method is described here: ... 2004 Mini Cooper

Truck has 195,000 on it. after it has been running for a couple of min the abs light and the parking brake light both come on, brake fluid is full, has new front hubs with abs sensor in them (last year), and just put on new front rotors and pads. Is there a sensor in the rear brakes that is setting off both of them?


Yes the rear has sensors, but seeing you just had front pads installed, I'd look for a loose or broken wire in the front first. I've installed front pads with the sensors and thought I got them installed right, come to find out they were not making g ... 1999 Chevrolet Silverado 1500

My 2006 F150 abs light would come on after driving it for a few miles. I changed the rear sensor and it still didn't correct the problem. I had the brake pads replaced and cleaned the front sensors. I had an error code on the front right sensor and after having the pads replaced and the code check again, the error code was gone. I drove it for a little longer period of time and the abs came back on. Is there any other solution you might have to correct the problem with my abs light. Than


It sounds like you might be having a problem with your Electronic control module. Are the only codes coming up just for the sensor? Have you recently cleaned your engine or driven in very wet weather? If so, water could have gotten into your conne ... Ford F-150
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 5.3014 seconds