Having problems with your 1996 Mercury Grand Marquis ?

Having troubal putting in new water pump in a 1996 murcury grand marquis how do I remove the belt and the fan to get to the water pump

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1996 Mercury Grand Marquis

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Having troubal putting in new water pump in a 1996 murcury grand marquis how do I remove the belt and the fan to get to the water pump


... 1996 Mercury Grand Marquis

Cant get the fan clutch nut off the front of the old water pump so the pump can be removed Have Cowl removed the fan loose and Two bolts removed from the Water pump pully and belt loose


Ok, it's best to have the fan belt ON all the way, that way it holds the pulley in place. Then, put your wrench on the nut, and tap the wrench with a hammer. This will break it loose, and then you can unscrew it the rest of the way. It works like ... 1993 Ford Crown Victoria

I am trying to replace the water pump om my 1995 Mercedes C220 (Not a C230) How do I get the tensioner pulley to release the tension off the water pump pulley and serpentine belt so I can remove the fan off the waterpump and then remove the waterpump.


TRY USING A BOX END WRENCH OR A SOCKET AND WRENCN TURN TENSIONER CENTER BOLT COUNTERCLOCK WISE TO UNLOAD TENSION WHILE SLIP BELT OFF THE ALTERNATOR.THAT WAY BELT WILL BE OUT THE WAY UNTIL YOU REPLACE WATER PUMP.WHEN DONE TURN TENSIONER CLOCKWISE ... Mercedes-Benz C230

1994 Grand Marquis (4.6L) leaking coolant. It drips from the front of the block under the harmonic balance. I need to remove the shroud so I can see the water pump which probably needs replacing. My manual says to remove the fan and then the shroud but there isn?t enough room between the shroud and the front of the engine to reach in and unbolt the fan. is there a better way? thanks in advance. ted


The fan unscrews without bolts. if you look between fan and pulley you wil see the big hex nut to unscrew. in other words it unscrews like a jar lid. p.s. it may be left hand thread it should say so on the shroud ... 1995 Mercury Grand Marquis

1992 Jeep Grand Cherokee needs water pump replaced and I can't seem to get the clutch fan to come off. I am use to working on chevys and have never had this problem. what am I doing wrong. I have removed the four bolts hold the fan to the pump shaft but it won't slide off. Is it connect by the 1-1/2 bolt? Please help


If you have the four flange bolts out, you may need to use a thin bladed screwdriver to separate the fan flange from the pump flange (a little wd 40 helps) There is no inch and a half bolt anywhere on the pump or fan so I have no clue what other bolt ... 2004 Jeep Grand Cherokee

How do you get the timing belt cover off on a 94 Ford Ranger 2 wheel drive with a 4 cyl. engine? Need to replace water pump. Have fan housing, fan, clutch and belt pully off. Do I need to remove anything else?


... 1994 Ford Ranger Supercab

Radiator after repairing a hole in the radiator it occured again in the same place and when feeling the top water pipe its very hard as if it going to burst,i checked the water pump, the belt and removed the water valve and its still over heating,however the fan is working properly in getting the temp down to normal but in traffic its overheating, any suggestions.


Hi you may have a build of rust and corrosion in the radiator, which could greatly diminish it's ability to cool the engine (slow speeds in traffic are the toughest time for a radiator to do it's job). I would recommend that the radiator be removed, ... 1995 Jeep Cherokee

Removing water pump 1997 jeep grand cherokee when you can't get fan off. and radiator removal if necessary.... help Thanks


... 1997 Jeep Grand Cherokee

I have a 1998 Rav4. Driving and it just died. Coolant everywhere and oil. Took it to Toyota who does my service work. At first told it was timing belt. Reminded them they just changed timing belt at 115,000. Then they told me it was the water pump that went up and knocked timing belt, stretching it off it's placement and caused alot of damage. They said on 98's water pump is difficult to get to and involves removing timing belt, etc. Asked them why they didn't check water pump whe


... 1998 Toyota RAV4

I am replacing a water pump on a 1999 dodge durango, 318 ci, 5.2 litre engine. i am already encountering problems, i started removing the water pump assembly, removed all the bolts, the whole things is loose. i did this in the rain. after i was done i noticed i have 2 different sized bolts, and completely forgot where the bolt go in what holes. next, how, with the assembly loose, do i get it out of the motor bay, still attached to the fan and fan clutch. i think might of got ahead of myself


Ur supposed to unscrew the fan at that big nut and remave the cooling fan shroud first then youll have all kinds of room. snug the pump back to the motor and break that nut loose. i always use an air hammer and chisel in the left of the top flat on ... 1999 Dodge Durango

I need to remove the water pump on a 1999 Pontiac Grand Am. What is neccesary to remove the front timing chain cover? I have the instructions to remove the water pump, but it involves removing the front timing chain cover, does the serpentine belt have to be removed? What all is involved?


Just to clarify i asked what size motor was in his car. The reason for that statement that removing the timing cover ,chain and exhaust wasent required to change the water pump is that on 3.4 V6 engines none of that is required. To change the water p ... 1999 Pontiac Grand Am GT

I brought my 2004 Jeep Grand cherokee to the mechanic because it is making a really loud squeeling noise(like when a belt needs replacing but times that by 500) and the mechanic said that it was the water pump..... I have never heard of a water pump making a lous squeeling noise, then he said itd be between 3-400 to fix. Well this morning he said it was going to be 500.00 because her also highly recommends getting the timing belt and the timing belt pulley replaced as well. My question or conc


... 2004 Jeep Grand Cherokee

Instillation of bracket idler also known as fan pulley bracket of 1991 toyota 3VZE motor.Part is bracket sub assembly OEM part #16307-65020. I removed the part after I changed my water pump and timing belt. I ran the truck when the pulley on this assembly froze I removed the part dis assembling the radiator, fan, timing belt cover and loosened the belts and such. I went to toyota and found that the part cost almost a $1000. I tried 3 different after market products but the bolts never matched u


Due to the age of this truck no diagrams are avial anymore, I can direct you to a used factory repair manual however, this will have all the information you need and is a valuable resource for any future problems u need to fix, it is a CDROM copy of ... 1991 Toyota 4Runner

Instillation of bracket idler also known as fan pulley bracket of 1991 toyota 3VZE motor.Part is bracket sub assembly OEM part #16307-65020. I removed the part after I changed my water pump and timing belt. I ran the truck when the pulley on this assembly froze I removed the part dis assembling the radiator, fan, timing belt cover and loosened the belts and such. I went to toyota and found that the part cost almost a $1000. I tried 3 different after market products but the bolts never matched u


... 1991 Toyota Pickup

Hi I just recently purchased a 92 Chevy Silverado with a 350 engine in it. The previous owner had busted the radiator in the truck. He had also removed the water pump off the vehicle. I put all of this back on the truck but I am having a problem trying to get the fan to run. It seems that the water pump in which the fan is connected is not functioning. I guess my question is what is it that I am doing wrong? Does that pump suppose to have something connected to it to make it operate?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To check that you’ve replaced the water\015\012pump correctly, ple ... 1992 Chevrolet K1500

Need exact procedure for removing the fan and clutch fan pieces so that I can remove the water pump. There must be one more thing to loosen besides the four bolts (13mm) on the fan blades and the four bolts (10mm) on the smooth belt pulley that attachs to the front of the pump. What am I missing? 5.7 Vortec with AC.


Leave the fan belt in place and it will hold the pulley and fan in so you are able to remove the large nut that is behind the fan ... 1998 Chevrolet Tahoe

1993 chevy van g20 water pump replacement, what parts need removed to get to the water pump, and how to remove the serpentine belt


You will need some fairly long wrenchs 15mm-16mm to get leverage on the spring loaded serp tesiner put a wrench on the pulley near the belt ? also loosen the 4 fan bolts on the water pump before you remove the belt ? ther are 7 fan shroud bolts you ... 1993 Chevrolet G20

Surpentine belt I replaced the water pump on my 1991 Chevy S-10 2.8 liter motor. In order to do this I had to remove other parts such as the A/C pump, power steering pump - Being careful to remeber where all the bolts go when I put it back together, well, I forget to take note of the surpentine belt & how it routes thru the pullys & also how to get it back on without damaging the belt.


Well first check your owners Owners manel. Also there is usual directions on were the belt goes under the hood so check there. ... 1991 Chevrolet S-10

Hi We have a 1997 mitsubishi magna with a 3.5 v6 engine. Is it a big job to change the water pump?the plastic cam belt covers seem to be a pain to get out,does the harmonic balancer need to be removed? i think the engine mount arm needs removal, does this mean removing the aircon compressor mounting bracket too? I hope you can enlighten me on these points, i certainly appreciate it. have tried to get a free manual from the net, but havent had any luck...would you know of a site? cheers and than


This job takes 4 to 6 hours for an experienced mechanic. The front of the engine has to be removed to access the timing belt. It is a job you can tackle, but you will need a manual to do it. If you plan to do it youself, buy a manual. there are criti ... Mitsubishi Montero

Running hot water pump was leaking (i noticed because fan didn't kick off when car was turned off so we checked water level). we replaced water pump and belts and car runs hot...so we replaced the thermostat, then radiator cap, then flushed the system (thought an air pocket could be problem) but car still runs hot! top radiator hose gets hot bottom one does not. we also ran it without a thermostat and still ran hot! help


Radiator Fan Control Relay Switch. I bet your electric fan doesn't run? ... 2002 Nissan Altima

I am trying to replace my water pump on a 96 mercury mystique. the hose that connects the radiator to the water pump is hidden behind the power steering pump, and the a/c unit, making it seemingly impossible to remove the hose from the pump(to pull the old pump out). Do I need to remove the power steering pump or a/c unit to get at the hose to remove the water pump? if so how would I go about removing ether, i have only spotted one bolt I can get at.


The a/c and p/s pumps have 2 bolts.One is a long bolt that runs throught the body of the pump and that is used as a pivot point to adjust the belt tensions.The other may be on a smaller bracket that locks the pump in place.Or it will have the second ... 1996 Mercury Mystique

I am tryilng to remove the water pump on my cadillac deville, 1998. The socket will not get tight when trying to remove the water pump. It will get in a bind if I attempt to tighten it, but that does not help me get the water pump off. What options do I have for the pump removal other than the tool?


... 1998 Cadillac DeVille

I have a 1987 325i that i am trying to bring back to life. I replaced the timing belt and water pump and all belts and hoses. Now the car getting hot. I have replaced the fan clutch like 2.5 years ago. When it get hot all the hoses are hot. Oh i also changed the thermostat as well. Does anybody have a suggestions?


If you have blead the air from the system then its a Clogged radiator. When an engine gets old then particals of rust build at the bottom of the radiator core. The reason for this is the hot water comming from the engine goes in the bottom pipe and b ... BMW 325

2004 pontiac grand prix, gtp , water pump replacement.. Do you have to remove the fuse box to get access to remove the pump


No, here is procedure according to autozone.com\015\012\015\0123.8L Engine\015\012\015\012\015\012Before servicing the vehicle, refer to the Precautions Section. \015\012 \015\012 ... 2004 Pontiac Grand Prix

How to remove timing belt cover on a 1989 Isuzu pickup 2.3 liter? I need to replace the water pump and it looks like I need to remove the timing belt cover to get to one of the bolts.


... 1989 Isuzu Pickup 2WD
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.6991 seconds