Having problems with your 1996 Geo Prizm ?

Turn signal not working, replaced fuse in fuse box underdash and still nothing

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Pull the panel with the hazard lights button, and make sure that connection is made. The way it's wired up if the hazard button isn't connected nothing will work. I had the same problem
Repair Help & Product Troubleshooting for 1996 Geo Prizm

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Turn signal not working, replaced fuse in fuse box underdash and still nothing


Pull the panel with the hazard lights button, and make sure that connection is made. The way it's wired up if the hazard button isn't connected nothing will work. I had the same problem ... 1996 Geo Prizm

I have no brake lights or blinkers on the rear of my 1989 Jeep Wrangler. I had one left blinker in the rear but not now. Both blinkers work fine on the front. I tried grounding the rear lights straignt to the battery with a long wire and nothing happens. I replaced the turn signal switch and nothing happened. I got a test light and get no power at light. I followed it to the connector near the fuse box and still cant get power. All my fuses are good. What can I try next????


Did you you check all your power ground sources from the switch to the light seem like you power source is not properly ground ... 1989 Jeep Wrangler

I have a 97 Nissan Sentra. It had a bad battery and i have replaced it but since nothing interior wise works...no turn signals, no windows, no heat, no radio. I thought it was a fuse and I replaced it(7.5 mini fuse and not sure what it goes to) but still nothing works.


Try the fusible link in the fuse box under the hood. very same thing happened to my sentra. of course you'll have to go to a dealer to get the new fusible link, but hey it was only like ten or twenty bucks. You should be able to tell if one is bad be ... 1997 Nissan Sentra

I have a 05 Dodge Neon and my blinkers do not work at all... The flashers work and lights up on the dash but when u turn the turn signals on .. It does not show up on the dash or none of the blinkers work at all... The fuse in the fuse box and under the dash have been replaced but they still don't work. Could it be the flasher or the MFS??


I would check for voltage at the flasher next. There should be a flasher for the turn signals and a different one for the hazards. ... Cars & Trucks

When i turn the igniton key to on the fuse for the heater/ac blows.at first the turn signal stoped working when the heater /ac fuse blew. I replaced the fuse. the turn signal and heater worked for 2 days then the fuse blew. I removed the fuse for the heater/ac and the turn signal worked for a day. now the turn signal does not work and when I turn the ignition on the fuse blows immedietely. I downloaded a fuse box diagram from wjjeep.com/fuses and it states that fuse # 20 10amp controls ignition


The ignition run is to the ECU or Engine Control Unit. And the blinker sense is for the blinkers to chime when left on for more than one minute. Finding these kinds of problems are very hard. Because from what you said earlier that it ran for 2 days. ... Jeep Grand Cherokee

Within the past month, both headlights have stopped working. Parking lights, high beams, turn signals and fog lights work fine. I have replaced relays, switch and tested the wiring from the headlights to the fuse box and from the switch to the fuse box and still they don't work. I have no idea what else to do.


Have you replaced the multi-function switch? It is common for it to stop hedlight funtion and allow other funtions to keep working. ... 2000 Chevrolet S-10

Turn signals don't blink. All signals front and back come on but stay steady. Hazard lights DO work and blink. Replaced the Flasher behind the fuse box on driver side and still doesn't work. Went back to auto parts and got another flasher and still doesn't work. I have a 1996 Ford F-150 Eddie Bauer Edition Reg Cab 2-wh Drive Straight Six. 5 Speed.


Check all your turn signal bulbs. When one goes bad it doesn't complete a full circuit causing your lights to stay steady. ... 1996 Ford F150 Regular Cab

My 1987 dodge ram chargers front and back turn signals dont work as well as my braking lights. My headlights and rear lights work. ive replaced the turn signal flasher and fuse that are located inside my under the steering colum and put new bulbs in the rear but still nothing works


... 1987 Dodge Ramcharger

My 1998 f150 left turn signal and brk light stopped working. I checked the ground at the light socket, its good. I checked for juice at the socket, no juice except for the running light, it has juice. I've replaced the multi switch at the steering colum, did not fix problem. I replaced both f&r light bulbs. Fuses all good in the box under the hood and in cab. Ive tried tilting the steering whl and playing with the turn signal actuating arm, still have problem. Any ideas?


The multifunction switch is going bad. ... 2004 Ford F150

My 1998 f150 left turn signal and brk light stopped working. I checked the ground at the light socket, its good. I checked for juice at the socket, no juice except for the running light, it has juice. I've replaced the multifunction switch at the steering colum, did not fix problem. I replaced both f&r light bulbs. Fuses all good in the box under the hood and in cab. Ive tried tilting the steering whl and playing with the turn signal actuating arm, still have problem. Any ideas?


Start looking for a broken wire or corroded plug-in at a connector going to the rear of the truck. Hope this helps. ... Ford F-150

I have a 1996 Jeep Cherokee and the flashers and turn signals have stopped working. The hazards are now working when I replaced a blown fuse but there is nothing for the signals still. I have runing lights, head lights, and all the fuses are fine. I noticed the hazard relay was VERY hot under the steering column when I checked it out, does that change anything?


... 1996 Jeep Cherokee

My instrument panel, turn signals,tail lights do not work. I've replaced a 15A fuse in fuse box in dash board and a 10A fuse in the fuse box under hood on driver's side. Also checked rear tail light bulbs-all fine. Still no lights. Suggestions? If another fuse or relay or whatever? Where do I locate it?


... Nissan Sentra

Turn signal/flasher just quit working. They were working fine till I pulled the fuse box down to replace another fuse/. Fuse for flasher/turn signals is still good


IS THE FLASHER STILL IN THE FUSE BOX OR PARTIALLY UNPLUGED ... 1981 Ford F 150

I had my turning signal, hazard and brake lights all go out at the same time. I had an extra brake switch from a neighbor that also has a 2003 Durango. Anyway, swapped that out and everything was still not working. The fuse for the Hazards and Turning Signals looked okay but I swapped it out anyway. Turning signals and Hazzards work now but still no brake lights. Tried putting back in the other brake switch and still nothing. I can't find a fuse for my brake lights under the hood or in the cab s


It seems that there is a fuse which is causing this fault,I would suggest you get a meter and test each fuse at a time,do not assume fuse is ok by just looking.Now if the brake lights work and your signal lights starts to play funny then test the fla ... 2002 Dodge Durango

I have a 90 chev 1/2ton the brake lamps are inop,i was towing a trailer and the turn and brake lamps became inop, checked fuses and found turnsignal fuse blown and the brake good,but the brake fuse was a 15amp and some one had installed a 30amp fuse, i replaced the turn signal fuse and the turn signals worked but still no brakes, so i checked the brake switch and found the connector and switch burnt, i replaced the switch and fixed the wiring at the switch still no brake lamps?


Use a test light and see if there is power to the switch. Then depress the pedal and you should have power on both sides. If there is no power to the switch, check the harness from the fuse box to the switch. If it got that hot, it may have melted th ... 1991 Chevrolet C1500

2003 jeep wrangler with no turn signals I have checked the fuse, and replaced flasher. still nothing, I pushed in hazard button and it made a buzz noise and then nothing . brake and tail lites still work. can you help


Sounds like the problem is in the selector stalk on the steering column. ... Jeep TJ

2004 Envoy XUV doesn't always crank. All the lights on the board light up and the radio and fan come on, but will not turn over. I have had it worked on twice for this. The first time he said a lot of fuses were blown so he replaced them. Secomd time he searched and followed wiring, but found nothing, but didn't charge that time. I have been reading other people's posts and trying to identify with mine. I replaced a relay under the hood in the fuse box, but still having ploblem. What do you thin


... 2004 GMC Envoy

Headlights I have a 2001 impala my head lights are not working on low beam. I have replace the relay fuse still nothing. lamp switch does not come on. I have a day time mood an this is not working until I put it in drive. This morniong in the dark I had nothing. untill I pull back on the turn signal for high beam an then I had to hold this in postion it would not click.]zThank you any help.


Pulling on the turn signal switch is called "flash to pass" and you are activating the high beam lights.Have you checked to see if you have power in and out of the dimmer switch on low beam ? ... Chevrolet Impala

My 97 mercury sable turn signals wont work. I had the entire assembly replaced and the fuses also but still nothing. the side and rear work but not the front either signal.


Spray contact cleaner in the hazard light switch on top of the steering column and press and depress several times. It worked for mine ... 1997 Mercury Sable

My drivers side turn signal stoped working. I replaced the bulb and it worked for a few days then stoped again. I checked the bulb and it didnt blow. Also checked the fuses and all seem to be good. Tried a second replacement bulb and still have nothing. Anyone out there got any ideas im lost at this point.


You are going to have to check wiring. Many it is the socket. If you have a test light or meter you can measure the voltage. There are several turn signal lights, front, rear, side, etc. Do any of them work on the drivers side? if not the ... 2005 Saturn ION

I have a 96 honda accord. A few weeks ago my turn signals didnt work. i inspected it and thought that maybe it was as simple as a fuse. So i replaced the fuse and sure enough it started working. two weeks later i get in my car after work and they turn signals fail to blink or click. I replaced the fuse again. when i hit the switch it doesnt do anything. So i went to a junkyard and found a switch from a 95 honda accord. i took out my old switch and put that in. This did nothing. the headlight par


I think that you have a bad flasher unit try replacing that. ... Honda Accord

TURN SIGNAL TURNING SIGNAL WHEN OPERATING NOTHING HAPPENS NO INSIDE SIGNAL, NO OUTSIDE SIGNAL CHECKED FUSE FRONT AND BACK STARTED WHEN DRIVER'S DOOR WAS REPLACE AFTER THAT PROBLEM STARTED SIGNAL WORK FOR TWO DAYS THEN WORKED ON &OFF NOW NOTHING DO THINK REPLACING DOOR HAVE ANYTHING TO DO WITH IT BUT I DO'NT KNOW. PLEASE REPLY SOON THANK YOU. JAMES


Sounds like a possible short in the wiring or a possible grounding problem. ... 2000 Nissan Maxima

I have a 2002 dodge ram 1500 pu , the lights kinda work , only one signal light works , on low beam one side works then I turn it to high and the other one works but not at the sane time , I have replaced modular 56051036af connected to the fuse box but nothing changed ??


... 2002 Dodge Ram Maxi

The cluster works when it wants to on my 95 dodge intrepid. It usually works when the car is left on for awhile. checked the fuses and the box already. i also took it to an electric service and they said it might be the bcm but turns out it wasn't because i tried to fix it and replaced it but same problem. i also cleaned the connectors to almost everything inside the vehicle but no, still the same problem. But the signal lights work and at night the lights work but it's just the other lights tha


I had a 95 Intrpid do this same thing and it seemed to have a mind of its own.. long story short i changed otu the dash and it stopped something was wrong with the micro processor in the dash/cluster. I hope this helps you, also i tried the BCM first ... Dodge Intrepid

2002 F-250. My back turn signal stopped working but the bulb was still good and the fuse was still good. Then all of the turn signals went out and when I checked the fuse again it had blown. I replaced the fuse and it blows when I turn the left signal or hazard lights on. I went through 5 fuses in about 3 minutes. what could be wrong?


You have a short somewhere in the wiring for the left blinker, which also explains the fuse blowing when the hazards are actuated. The easiest way to check this is, with the engine off, take a multimeter, set to ohms, and touch the red lead to one si ... 2002 Ford F250 Super Duty SuperCab
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 5.2808 seconds