Having problems with your 1996 Ford Taurus ?

96 taurus Haven't worked on this vehicle.Is the cv joint assembly hard to change.

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Same as any ford,simple but regular...
Repair Help & Product Troubleshooting for 1996 Ford Taurus

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

96 taurus Haven't worked on this vehicle.Is the cv joint assembly hard to change.


Same as any ford,simple but regular... ... 1996 Ford Taurus

About a year and a half ago my 93 buick century died and i got a bunch of work done: parts added included: alternator assembly, interstate battery, starter assembly, ball joint, door window motor, primewell ps 850, under labor it does say that they checked charging system, removed and replaced alternator assembly, battery, starter assembly, ball joint, gave an oil change etc, door window motor. not too long after, i went to drive to the store and when i depressed the gas pedal the headlights


Thanks for choosing FixYa and welcome. ... 1993 Buick Century

Growling noise from front of my taurus while driving, it also makes a whining noise when i steer hard left. i had the right front wheel bearing changed but the noise's are still there. also the inner cv joint on right front is pretty loose like i can wobble it with my hand-could this be the source of my noise's? i was told that the inner cv joint has lots of play. but this much? also left inner cv joint i can just barely move it. could left wheel bearing sound like this and if so can the sound t


Cv joints will usually pop when they are worn out. I would suspect that its the powersteering, check the pumps fluid level and the tension on the belt.\015\012good luck dont forget to rate ... 1997 Ford Taurus

2004 ford taurus heater will not blow hot when i turn the temp control i hear nothing, no change in the cold air. when the blend door actuator is working i should be able to hear it right? the a/c works great and all the doors i can hear open and close on the vent selector switch. and last is it hard to get to for replacement?


... Ford Taurus

What will cause a 2001 mercury cougar to pull hard to the left? We already changed lower ball joints, caliper, bearing hub assembly, and outer tie rods.What's your problem?


... 2001 Mercury Cougar

AC/Heater controller is not working. It is stuck on one setting will not switch from Vent to Floor to Defrost. Rotary was hard to turn and broke loose, now moves to different setting, but does not change settings. Will replacing the whole assembly fix the problem?


Yes it should. The assembly should have a few wires plugged into the rear of the unit. It's plug and play. ... 2004 Isuzu Rodeo

I have an 01 Taurus 3.0 OHV flex fuel. the car idles at around 50 PSI of fuel pressure. when accelerated it drops to 5 PSI and will hardly run. I changed the pump twice snd still the same thing. The regulator is built on the pump assembly. I dead head the pump and car runs great. any ideas. at a lost so far


Airtech pumps usually will just quit, I suspect fuel line going back to tank kinked. ... 2001 Ford Taurus

Toyota corola 1982 4k gear box problum, i change gearbox from 4 speed to 5 speed gear box, now when in 2nd gear shifted its sounding hard, and 4th gear is not working, when i revers the gear from 3rd to second its again hard sounding,3rd gear is ok but 4th is not working, kindly help me may i reinstal my old 4 gear box, actualy car is mazda rx7 1986 model,engion instaled is toyota corolla 1982 4k with 4 gear, , i change it with 5gera , then this problum faceing,


Get a used transmission to much to repAir\012 600. Parts to repair find used oneghggg ... 1990 Toyota Corolla

I had my toyota carina cv joint change. after the cv joint change the speedometer does not work and the abs light haas come on My main worry is the speedometer which is not working. I assume it has a sensor where is this sensor locsted


... Toyota Corolla

My son took his 97 toyota tercel in for a simple oil change and filter change and an air filter change and also a fuel filter change..well, it went fine until the fuel filter change..jiffy lube couldnt remove it..so they worked hard to do it..once they started they couldnt quit..it was half undone and they couldnt leave it there..so they took it off..well, they said the screw in part was cross haired..or whatever..and so they worked at trying to starighten that out..they couldnt..they tried to p


I figure that you have got a whole lot of issues to solve. In the first place make a record of the maintenance to be done on your dear car with a systematic approach. There is a time frame as well as the running mileage maintenace that keeps your car ... 1996 Toyota Tercel

Headlight bulb I have a 2008 2500 hd sierra slt Duramax I was looking how to change headlight bulbs.Booklet says to change remove air cleaner and reach in and change them from the back. That won't work no room to even see the back of headlight. Looks like there is 2 bolts holding the assembly in and it should swing out like a 2001 gmc with there pins. the assemblys come out just dont know where to push thanks


You have to remove the air intake filter and then kind of reach around up in there to change it. It can be done, but is a lot of work. On the duramax, it is even harder to do the driver side because of the dual batteries. You have to remove the batte ... 2008 GMC Sierra 2500HD 2WD

Tail lights Since i changed my stereo in my car, my dash lights and my tail lights havent been working. They dont work at night but they work when i put my breaks on and my turn signal on just not when i have my headlights on at night. Someone please help i changed the fuses and the bulbs and i still dont know what to do.


Where can i find this wire at??? i hope that i can fix it! ... 1995 Toyota Paseo

I changed engines in my 98 continental and now the power steering doesn't work. It isn't leaking and the hose isn't pinched. I checked the belts and I still can't figure it out. It was working just fine when I changed motors but now it isn't working and it is very hard to steer.


You may have air in the system. Start the car and move the steering wheel back and forth and keep checking the P/S fluid level while the car is running. Keep adding fluid when it's low. Keep turning the steering wheel back and forth and sooner or lat ... 1998 Lincoln Continental

My car turns but wont turn over,i had the distribtor,rotor,ignition coil,plug and plug wires changed,only thing i havent changed yet is the fuel filter which i have but havent put on yet could that be the problem.it worked ok before i changed the other parts.not sure what to do now?


First make sure that ur getting spark, at the spark plugs if no check your rotor button and distributor cap make sure that its not put on funny. if you have spark i would see about fuel, fuel filter not a bad idea.also check crank sensor if no spark ... 1997 Dodge Neon

I have an AXODe from a 2000 Windstar. My car is a 1998 Taurus. The only difference is the Windstar transmission has a VSS and the Taurus has an OSS. My question is, can I change the connector to the VSS and will it work properly for the PCM of do I have to put the OSS on the transmission for it to work correctly. If I have to put the OSS in, does the Windstar transmission still have the plastic gear on the shaft for it to work properly?


... 2001 Ford Windstar

93 Ford Ranger had no pedal changed brake booster and master cylinder bled Breaks several times now pedal is as hard as a rock! I Tried to drive it the brakes work but when I hit them hard they locked


I would hope they lock up when you hit them hard! ... Cars & Trucks

The dash lights and rear brake lights in my 94 ford taurus won't work...i changed the lights twice and still no action!! its very frustrating because i cant drive when it gets dark..my dash board lights also do not work, they both stopped operating at the same time..i have changed fuses in the main fuse box under the hood and the same results


Hi,maybe i can shed some light on the situation.Are we sure it is the stop(brake light)lights that we are talking about?Or is it the tail light?I it is the tail lights,then it is most likely the head light switch itself.The dash light and running lig ... 1994 Ford Taurus

I have a 2002 Ford Taurus and the radio just stopped working it was flicking on and off then just went out.There is no clock or nothing and no power.The climate control and everything still works fine. So I replace the cluster for the radio controls still no change I also changed out the radio tuner amp in the truck still nothing. I also checked all fuses and all looked fine none blown. Does anyone out there know where and what I can do now? No radio sucks!


... 2002 Ford Taurus

Hyundai h-12.4 svx 4p 112 cv 1998 7 seater,clutch pedal sticking down works ok when cold but after long run on motorway back on normal roads hard to get in gear crunching alot of time, is there cable ajustment at pedal end or is it hydrolic,could it be cylander or need bleeding,drove van back from spain no probs on motorway at top speeds only when come off and try to change gear have to put foot pedal hard to floor works sometimes but in general crunches in to gear


... Hyundai Motor 1998 Accent

My truck is having a hard time starting but eventually it would start. I changed all spark plugs an what is the next step. If my fuel pump works ill change the fuel filter again. If the fuel filter didn't work what next an the relay what do I do an check. Please help this is a great website thanks.


Make sure the plug gaps are 25th as a wide plug gap will cause bad starting ,cannot see a fuel filter causing bad starting though but as a thought first check the vacumn pipe to the fuel opening valve on the fuel rail is a valve with a vacumn pipe ru ... 1998 Chevrolet S-10 Pickup

Need some direction in trying to fix a 2007 chevy 2500 with 6.0. Power Steering went out while playing in snow in 4 wheel high. Replace pump with 3 different remans and now with a new ac delco. have power steering now but is hard to turn while setting still until rev motor then the power steering works, and when braking hard and turning the power steering doesnt work. when i changed the pump the first time there was alot of metallic flakes in the fluid. i have flushed the system several times, b


I would look elsewhere in the hydraulic power steering system for where the metal flakes originated. ... 2007 Chevrolet Silverado 2500HD

Hard starting My car has the problem of hard starting.i av changed the kick starter and battery couples of time.when i crank the engine,the fire keeps returning instead of starting the engine.Even when they work on it,it will only work for just two or one week.Pls help i am tired of the car.


Give this in morew detail, but without seeing it it could be a lost cause ... 1996 Nissan Maxima

My chevy thaeo has a big promblem i change the power sterring pump,the car was working well but the old pump has a liquid fuid sow i change it but when a but the new one the car works well driving but when i stop and i turn the wheel it is very hard i did a fush on the sistem if it is air but nothing happen a check the sector and it is ok


Check to make sure you have a tight belt and a good tensioner ... 1997 Chevrolet Tahoe

Check engine light came on, fault is for the Cam shaft position sensor. I changed the sensor. Didn't work. I changed the whole synchronizer assembly. Didn’t work. I checked the wiring, all good continuity (I didn’t use a break out box, just followed wires). I have read about possible problems with the computer or even the timing chain. Has anyone heard of a similar problem and what were some of the solutions? Thanks,


OK, on a 1998 Ford Taurus have a service engine soon light. Scanning it said the Camshaft Sensor circuit was bad. So I replaced the camshaft sensor. Cleared the code and it came back.In the winter time it comes, and in the summer time it ... 1997 Ford Thunderbird LX

How hard is it to change the ball joints on 89 f250 4x4 does the ball joints press in or have clios and what basic tools do i need and what is the time to change both sides upper and lower


It's a bit of a job especially if you live in the north where road salt is a factor. You have to remove the brake calipers, then lock-out, then the hub, (special tool required). Then the spindle, which is usually rusted in and can be a bugger. Discon ... 1989 Ford F 250
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.4412 seconds