Having problems with your 1996 Ford Explorer ?

Back light assembly

\015 Why does'nt the brak light bulb fit into the harrness\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1996 Ford Explorer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am trying to replace a bulb in the rear tail light of my Chevrolet Lacetti. I have opened the tailgate and removed the two screws which hold in the light assembly but still cannot get the assembly out. I have then peeled back the carpeting inside the trunk area to reveal the back part of where the assembly is located. This is where I get stuck as there does not seem to be any screws or anything. All there is are two plastic things which move when I jiggle the light assembly but does not seem a


Try to turn the two plastic things counterclockwise to loosen them...on many GM tail assemblies these are actually hold-down screws...to re-install insert onto bolt and turn clockwise to securely tighten...you probably did not have to remove the two ... 2005 Chevrolet Aveo

I am trying to replace a turn signal light. Removing the rear tail lamp assembly is giving me troubles. I removed the nuts from the 2 screws in the back of the assembly that attach it to the inside of the trunk, and lifted the tab, and removed the wires attached to the light. But the assembly still doesn't come off. Is there something else I need to remove, or does it just take a lot of force to remove the assembly?


I assume this is a sedan. There may also be a 'locating' pin that must be removed (some sedans).... otherwise pull assembly straight out. ... 2006 Pontiac G6

Brake lights on '99 Expedition sporadically light up. It seems that the cable that goes into the switch assembly for the brake light is a little too kinked so if I attempt to move the cable over and take some of the kink out of the cable the brake lights work for awhile, until the cable goes back to the old position. Also, are those assemblies easy to replace. It seems you need a childs fingers to replace it.


... 1999 Ford Expedition

Rain water leaks in around the right and left sides of the back light fixture. Can't figure out how to remove the entire light assembly to get to the potential area where the water seems to be coming in. I've taken all of the trunk interior covering out. I've poured water on both sides of the light assembly and the water comes thru the brake light cavity and drains into the wheel well. The entire carpet base and the carpet gets sopping wet. I tried descibing the problem yesterday but todays de


The water is almost certainly leaking in around the body seals of the tail light assemblies. In order to provide any further assistance I'll need the model and the year of Buick. You will also need to replace the taillight body seals. ... Buick Park Avenue

Headlights keep going out alternating from side to side sometimes both, but when I pull out the assembly and twist out the bulb the light light goes back on. Samething when I disconnect the wireing and reconnect, the light comes back on. Is this some type of warning feature or a wiring problem ? The connections dont seem to be loose or corroded. I have not replaced the bulbs yet but it maybe my next step.


... 2006 Buick Terraza

97 Passat Dash Light Dimmer Test. I want to test the rheostat that dims the dash lights. I've removed the light switch assembly, it is in one unit, a rotary/pull knob for the parking lights, headlights and driving lights and a thumdial rheostat for the dash light dimmer. One large electrical connector goes into the back. I'd like to test the rheostat and need to know which terminals I need to check resistance between. alternately if I knew the wire color that went to the dash lights I could


Hi. There were some mid year changes to things like wiring diagrams for your Year Model. It is a great car too. Take down the vin number [ check for RECALLS while your at it] and call or go to the local dealer - they will fax or print out ... Volkswagen Passat

Dash and tail light are outTail light and dash lights are not turning on and the tail light 10amp fuse is blowing as so as the light switch is turned on. I have checked all the bulb, sockets, by passed my remote starter, installed a new light switch, pulled up the rocker panels, disconnected the socket in the back seat that supplies power to the rear light, pulled oout the dash assembly, pulled out the dimmer switch, removed all the relays and fuses, and more and it still is blowing fuses.


You may have the wrong wires hooked into the switch. try testing the wires with an ohm meter and making sure they are both the positive wires. always disconnect the negative battery terminal before installing any electrical devices ... 2003 Toyota ECHO

Fog lights 1) Noticed (driver side fog light out); passenger side light working; and internal switch with fog light on (shows green illumination). 2) Get new bulp for light out - put in. Still does not work 3) Open up fog light assembly to view working one (to see what I possibly missed - that one still working. (car running lights on) 4) move back to inoperative one (remove retainer clip) suddenly get a spark and it shorts out (I believe) either a fuse or otherwise blows out the one that was wo


Check fuse #7 in the fuse block inside the vehicle and fuse #25 in the fuse block under the hood...more than likely you blew one of these fuses when it sparked. as for the drivers side being inop once you replace the blown fuse if you have a test lig ... 1999 Jeep Cherokee

Water recently got into the rear light assembly of my 1993 Honda Accord EX. I realized this when my 'brake lamp' warning light came on...I removed the water and cleaned up the sockets. The signal light is working and the running light works when I turn on the headlights, but I can't get the brake lights(passenger side rear, trunk hood or back window)to work on the side that got wet. The only part that doesn't light is the filament that lights when the brakes are applied. Besides drying out every


Did the water short the system out and blow all the bulbs? ... 1993 Honda Accord

Part name and number needed...1998 Mitsubishi Mirage 2-door coupe...i bought the car, the front passenger side turn signal/parking light was broken and right front blinker wasn't working...ordered whole new assembly...went to install new assembly and noticed that the part the bulb plugs into, one of the wires is cut...i need a new connector or terminal or socket, i'm not exactly sure what part it is. it is where the wires go into and the whole part plugs into the back of the light. i can't find


Call your Mitsubishi dealer. The parts department surely has the part number and probably can order it for you if they don't have it. ... 1998 Mitsubishi Mirage

Check engine light was on and car running hot when idling and sometimes while driving. Had fuse replaced did not fix problem, then had fan assembly replaced. Check engine light came on again, running hot while idling. When car heats up right fan goes off but will come back on when turn A/C on but A/C not cool when idling. I have two mechanics telling me fan assembly needs replacing again (its just been 3-4 months) and another shop telling me its a computer/circuit problem. What do I do, I really


If the fan goes on with the a/c then the fans relay is bad ... 2003 Chevrolet Impala

High beams work when light stalk is pulled back. But when pushed forward hight beams do not go on. When the stalk on the steering column is pulled back the high beams work fine. When the stalk is pushed forward the switch sounds and feels like it is working fine, but the hight beams do not go on. I am not sure if it is a switch assembly issue, or a wire problem. Previous owner cut the white with black tracer wire from this assembly and connnected another wire to the engine side of the white/blac


I had this problem on a 1994 Prizm... Replacing headlight relay fixed it.(It's a plug in module in the engine compartment fuse box.) ... 1995 Geo Prizm

I have a jeep grand cherokee 2001, my tail light on the drivers side dosen't work, i replaced the tail light assembly, and it worked for a couple of weeks, now it's not working again, the turn signal, brake light, and back up lights work, i don't understand why the backup light work and not the tail light


... 2001 Jeep Grand Cherokee

When headlights are on there is a light in the back right tail but you apply the brakes and there is no brake light just a partial yellow colored light and the turn signal blinks very very slow. I have been told from people driving behind me I have no brake light on the right rear tail light. We have changed all the bulbs and it still does not work. I was also told the wiring is corroded so it is the entire assembly or what?


Likely a bad ground. ... 2007 Chevrolet Malibu Maxx LTZ Hatchback

All brake lights out fuse is good and bulbs are good thinks its a ground but don't know where to look. found two wires in back of left rear light. one wire connected to body of truck goes nowhere else just hanging. other wire red connects to female adapter in tail light assemble then deads ends connects to nothing. wired both dead end wires together still have no brake lights. what to do now


BUY A HAYNES REPAIR MANUAL.IT HAS ALL EXTERIOR AND INTERIOR LIGHTS - HEAD LIGHTS AND BRAKE LIGHTS DIAGRAM.I SEEN MOST CARS AND TRUCKS THE TURN SIGNAL SWITCH IF GO BAD YOU WONT HAVE NO BRAKE LIGHTS. ITS SHARE THE SAME CIRCUIT WITH BRAKE LIGHTS . ... 2006 Toyota Tacoma

Replaced brake light switch and both brake light assemblies; still no brake lights! Manipulated connections, i.e. bent them and had brake lights for a month...now no brakelights, no taillights and the parking aid is going haywire and beeping when I am driving down the road verus backing up! Help! Also keep getting TCS error.


... 2002 Oldsmobile Silhouette

Short in rear tail light assembly no back up lights no brake lights on drivers side only 1995 cirrus


Could be a bulb that has blown and shorted out internally - so test all bulb resistances b4 looking elsewhere.\015\012Dave ... 1995 Chrysler Cirrus

Replaced front bearing hub assembly on 2005 saturn ion (ebs) with a non ebs assembly....because it was the part that looked like the one I took off. the ebs assemblies did not fit and autozone looked at the manuals and everything came back to the non ebs....so the ebs light is on.......does anybody have a clue why a vehicle equipped with ebs doesn't have a replacement part?


... 2005 Saturn ION

2001 jeep grand cherokee left brake does not work period. I replaced bulb and fuse to no avail. the entire tail lamp assembly looked brown as though it heated up. However, the tail light, signal light and back-up lights still work. Please help.


Check to see if there is power at the connector if not check wires under back bumper where they connect ... 2001 Jeep Grand Cherokee

I want to remove the headlamp assembly in my 2004 LaSabre---the low beam is not working--new bulb--swaped with other side is OK--fuses swaped--problem did not change to other side---no power at the drivers side low beam---Is there a 3rd screw or something holding this assembly in? I removed the two screws that allow the assembly to "swing" out a littlwe ways but the back part of the wrap around light does not want to come lose.


Isnt their a fuse for each side headlight ?? ... 2004 Buick LeSabre

How do you remove the tail light assembly on a 2000 new beetle? I removed the knob on the back of the assembly and I am still unable to remove the assembly.


One you remove the knob. take a flat head screwdriver covered with like electrical tape or something so as to not scratch your paint. wedge it behind the tail light right where the bumper meets with the fender and pry up. thats it! ... 2000 Volkswagen Beetle

Can't put rear light assembly back on


There is a clip on the outboard forward corner of the light assembly that looks like a spear point. Look at the new assembly and check for the spear point. Now look at the hole in the body that the spear point is supposed to fit into. There may be ... 2007 Honda Odyssey

Blower problem Thanks Pal. Changed the power module assembly aka amplifier, located behind the glove box. Solved the problem. Still looking for a solution for the fuel filling problem. Engine light is back on and fuel keeps splashing back. Takes a long time to fill.


I am going to take an educated guess and say, that your "check engine light" is for the EVAP system, codes like P1448 (vent control valve) is stuck shut not allowing the vapors to escape while you are filling up, shutting the pump off. Let me know wh ... 2002 Nissan Pathfinder

Brake Lights. I check for power and I have it to the swith and leaving the switch I replaced the switch and the blinker arm. The blinkers still go off on there own and no brake lights. Their is a large relay part# 04671714aa on the back of the blinker assembly could that be the issue?


This is a part only found at the dealer,it is a lighting module of sort,this part number is not any good,except the dealer. ... Plymouth Neon

Hello i changed out my wheel hub assembly and my abs light is on now and i even changed it back with the old hub and still shows the light on


Disconnect the negative battery lead for a minute or two and reconnect. You disconnected the sensor while the battery was still connected. ... Chevrolet 2500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.2573 seconds