Having problems with your 1996 Chevrolet Camaro ?

I have a 1996 camaro ss and i am gettting an evap vacuum switch code.. any help on where to purchase nd how to replace please?

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 1996 Chevrolet Camaro

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1996 camaro ss and i am gettting an evap vacuum switch code.. any help on where to purchase nd how to replace please?


... 1996 Chevrolet Camaro

2004 chevy avalanche 1st and reverse strong in tranny. no 2 3 or drive. replaced neutral safety switch on side . did not help. Check engine light came on after switch replaced. can not scan for code says to hook up scannerand it is and key is on on position scanner turned on. help please


... 2004 Chevrolet Avalanche

HELLO I HAVE A CAMARO Z28 1997 LT1 OVERHEATING PROBLEM I REPLACE THE COOLANT TEMP SWITCH REPLACE WATER PUMP,TEMPERATURE SWITCH,RADIATOR CAP, I DID TO MAKE SURE IF MY FANS WORK I DIRECTED A POWER TO THE BATTERY FOR BOTH FANS THEY WORK BUT I NOTICE MY FAN DOES NOT WORK I NOTICE MY RADIATOR COOLANT LEVELER IS ON MY DASH GAUGES I DONT IF THATS IS WHY MY FAN IS NOT WORKING PLEASE HELP THANK YOU ERIC


Thanks for choosing FixYa and welcome. The most common issue would be a sticking thermostat or a bad one. You could also have a bad head gasket, valve, or impeller. You have already changed everything else. ... Chevrolet Camaro

Theftlock loc I have a 1997 buick park ave that I purchased from my grandma, it sat for a long time and lost it's charge, I replaced the battery and now the radio is locked. I tried holding down the 2 and 3 to get the code to call the 1-800-537-5140 to get the code reset but it just says loc and wont display a code. Please help I really don't have the money to pay a dealer to do this.


Try to pull radio out some of them brings the code on a stiker ... 1999 Buick Regal

Radio code... Bought a replacement radio for my A4 but it didn't come with the codes as it was from a salvage yard. I have my receipt &VIN. After I switched the radios out the newer radio went into SAFE mode. I took it to the dealer and they want to charge me OVER $100 for the code. Is there ANY WAY around this? Dealers used to do this for free! Can you help me please?


You can not get it from internet as i try with my chrysler almost a week. I was planning to get a 2nd hand one to install but the size do not 100% fit and look very cheap. Finailly, I have contact him and get a cheap quote and get it done in hr. now ... 1996 Audi A4

Purchased 1995 VW Cabrio Automatic 90,000 miles. Sometimes it will not start, meaning when you turn the ignition key no click no start. Have replaced the Ignition switch & starter assembly. Problem occurred again today 9/2 after replacing starter on 8/29. Car used every day. Always starts in morning. Daughter drove to school car sat for 2 hours when she tried it would not start as above. Please help


Now normally on these cars its the ignition switch that plays up ,now what i would do is to run a wire direct from the starter motor solonoid ,small wire on the starter motor and leave enough slack so it can be tied to the battery cable on the positi ... 1995 Volkswagen Cabrio

Please I need help. I have a,1995 geo prizm. I have replaced the fuel pump, fuel filter, fuel pu relay switch, temp sensor. Took it to a shop and hooked up to machine for check engine light and found out about the sensor. The other code was 14 no ignition reference signal. Guy a shop doeant know what that means. My car takes a long to crank when its cold. Does anybody know what it means? I hears I need to reset igmitor switch but cant find it


It's not really a switch. Below is a desciption of what the code means. In about 50 percent of the cases it's a bad connection which is causing the failure and there are many tests to check different circuits. In order to rule out the ignitor here is ... 1995 Geo Prizm

Service engine soon light won't come off, it reads 5 different codes related to the transmission, a garage told me that i needed a new ignition switch....i got the ignition switch replaced and the light still comes on????? please help


GIVE ME YOUR CODES.I WILL CHECK THEM OUT TO SEE WHAT CAUSING YOUR PROBLEM. ... 1997 Chevrolet Blazer

Have a 2005 Nissan Pathfinder that stops while I'm driving. I replaced the fuel pump last year, just got a new battery. Check engine light code is P0430. Some say its just a relay switch, others say its the catalytic converter. Please help, any advice will help.


A plugged catalytic converter would result in a lack of power. Usually very consistantly. A more likely option would be the ignition module or crankshaft position sensor but not absolute. Below are possible causes of the code P0430:\015\012 ... 2005 Nissan Pathfinder

Engine stalling After driving for a while, the car stalls when slowing down--the other night it stalled as i was driving, not braking- the brakes lock up and so does the steering. We purchased a new battery and new cables to a tune of $166.00, didn't work, than we had the oil censor switched at a tune of $90.00, didn't work, than they replaced the ignition module and that hasn't worked, haven't gotten the bill for that one yet. Please help.


Sounds like a faulty crank position sensor. its located behind the crank pully. they are known for failing. you will want the front crank seal done at this time also. ... 1997 Pontiac Bonneville

My 1991 Camaro rs 3.1 runs rough in gear but not at idle, and fuel pump runs the same without a fuel pump relay, I have 10-12 lbs of fuel pressure at intake-whether engine running at idle or just key on. Car was owned by a weird fellow, Do I have an electrical issue? (shouldn't run without a pump relay?) or should I replace pump again and filter again? No engine light codes. I've tried it all. Even "idle learn" idea. Please help, it's my only vehicle and I've spent over $2000 with bs knowitall d


... Cars & Trucks

P1602 code P1602 Loss Of EBTCM Serial Data What does this mean and what are the exact locations im suppose to focus on ive checked the connections to the hub there good hubs are brand new i few days before this issue my alternator went dead and cut the whole carr off i had to replace it at the car wash ive herd something about the ingintion switch could be faulty and its not getting communication with the ebtcm is that true? what could it be please help ....


... Cars & Trucks

I just replace the clutch master cylinder in my 1991 camaro and now the pedal sits WAY too high and will not depress enough to engage the nuetral/safety switch. And YES I did bleed the system. Can anyone please help me with this problem?


LOOK UNDER THE PEDAL TO SEE IF THERE IS AN ADJUSTMENT ... 1991 Chevrolet Camaro

Was driving on freeway and my 93 jgc motor just died and i rolled to a stop fuel pump is new and working replaced crank sensor, cam sensor, map sensor, tps, coil, plugs, wires, cap, rotar, ign switch, coolant temp sensor and i have 2 pcm's that work and both flash error codes 12 and 14 i am stumped and angry please help me !!!! ps alarm is bypassed it is grounded out inside drivers side door


I found DTC 12 indicates battery input to the Powertrain Control Module (PCM) was disconnected during the last 50 key starts.(you possibly had unhooked the battery at some point?)I found DTC 14 for vehicle OBD1 to be >>1 ... Jeep Grand Cherokee

Good Day and Happy Holidays. I have a 1993 Mercury Grand Marquis, Our brake lights don't work. I was told that it is the Brake Light Switch, I don't know where this is nor how to remove it. I have already purchased one just need some help to locate it, remove it and replace it. I must share that my husband is 77 years young so please make it simple. Respectfully Mrs. Armstrong


... 1993 Mercury Grand Marquis

I have a 89 chrysler new yorker, i have no spark I have tested the voltage at the coil and only got about 2.5 volts after about 5 sec of cranking,replaced controller and got 0 volts at the coil after 5 sec of cranking, also i can not retrieve any codes from the dash on either controller please help, ....the car ran when it was parked about two years ago


If the positive side of the coil does not have 12 volts,then replace the ignition switch.And also check all fusible links ,on the vehicle. ... 1989 Chrysler New Yorker

I have a ford transit MK6 van and i buy one 6000 eon radio cd. i replace the old one with this i give the code correct and the radio starts. after 15-20 sec the station is stop and all the stations are dissapear from the radio. i try serching for stations many many times but nothing. the next day i switch on the radio and is working ok for the next 15-20 sec and after the same. the cd is working perfect without any problem . please anyone know something to help me ?


... Cars & Trucks

I have a 1998 Ford Escort ZX2 4cyl. I am having a problem with my car starting. Sometimes it will crank over OK, but other times I will just hear a click, as if it is not getting good contact. I have replaced the starter and I have checked the battery and terminals. I recently purchased a starter relay switch but I am having trouble finding the location of the starter relay switch to replace it. Could you give me any help finding the location of this switch or any other help solving this problem


Hi.my paretner had the same problem with her car.\015\012We sorted the solution by disconecting the terminals on the battery.\015\012on the negative terminal there should be two thick leads of which both go to the negative side of the bat ... 1998 Ford Escort

P1345 Chevy Silverado 1500 4.3 V6 Engine Standard Transmission After I Replace The Intake Gasket I Ran Into This Code P1345 Which Is Cam Position Sensor. I Did Everything I Could And I Still Have Code Coming Back. After I Replace Sensor Check Engine Was Off For Day Or TWo And Came Back On Again With Same Code........... What To Do I check My Timing And Its Lined Up Perfectly Please Help PLEASE


... Cars & Trucks

Car drives and shifts OK then out of the blue bogs down and has no power exhaust manifold glows orange. After cooling the car runs and drives fine. Cat converter replaced and flow tested car drives fine then the problem reoccurs after a few miles. Engine codes p1361 and p0740 read simultaniously. Erase the codes then they both return at the same time when the car bogs down with no power. The car goes from running great to almost no power instantly. Timing belt also replaced. HELP PLEASE HELP


Disconect trany solenoids if you can test it at lower speedsi,,distribuitor may go crazy ,like high voltage going to wrong wires so change that if it is easy enough,fuel pressure regulator may play a roll or coolant temp sensor under the distributor ... 1992 Honda Civic

My service 4 wheel light comes on and then shuts off its a push button 4 wheel drive system so when I switch it into auto 4 it switches to 4 low when I try to switch it back to 2 wheel drive then put it back in auto 4 it will switch to 4 low or high I try to have a code run but no code shows up I've switched out both front hubs the only thing I can think is that it's the front actuator or there's a problem in the transfer case I need help please and thanks chevy chick


Its the motor to your transfer case. Yes it has its own but its like a $600 dollar fix. Just happened to my gmc serria ... Cars & Trucks

PLEASE! Need radio code for '01 Audi A6 Radio # AUZ5Z4Y0147237 Your help is appreciated ! I have a 2000 A4, had to replace dead battery, radio on safe mode, bought car used, cannot find radio code, called Audi dealer where car was last serviced, told me radio had been replaced in 2002 but they didn't have the code. Any suggestions apart from going to dealer? Thanks


Http://www.radio-code.com/ ... 2000 Audi A4

I have a 1999 lexus rx 300 the car came in with a code of p 1356, we replaced the ocv with a used one, and a month later the same car came back with the same code,can it be that the used ocv was faulty?? and if we do replaced the ocv with new ones and the code does come back , what else should done??? please help me find a solution to fix this problem.... thank you,


Hello! The OCV is located on the cylinder head and controls the camshaft\015\012 timing by advancing and retarding it with oil pressure... First step would be to remove the Oil Control Valve and \015\012check it for normal operation. You can pull i ... Lexus RX 300

Problem with not being able to starting S40 Volvo yr 2000 i had 2 starters replace, battery good, alternater replace, key change, relay switch replaced can any one help me i already spend a fortune and 3 mechanics can't find the problem even the volvo dealer can't find the problem it is now occuring every 2 weeks i never now if the car will start or not please help thank you


Possible a earth strap corroided inside the casing, requires wiring diagram and checking all power and earth points and resistance through the wires to make sure that they are ok these cars suffe with the loom across the front of the subframe corroid ... 2001 Volvo S40

1997 Chevy Lumina, I replaced the passenger side power window motor due to the factory one failing, The person before me cut all the wires going to the motor and toggle switch in their attempts to fix / replace the motor, The new motor does work but I had to order and new switch and pig-tail plug for the switch because it is missing - the new pig-tail plug did not come with a wiring diagram and is not color coded. Only all white wires Can you help with a wiring diagram in order for me to wir


... 1997 Chevrolet Lumina
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.2487 seconds