Having problems with your 1996 BMW 318 ?

How many pouns i need to put on 96 bmw 318 is head bolts

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Ok its a little diffrent for this vehicle you have a 3 step prossess for each bolt as listed below
first tourqe all bolts to 22 ft pounds then when they are all tourqued to that ft pounds
then turn each bolt an additonal 90 degrees then after you do that to all the bolts you must turn them all another 90 degree and that is how tight they should be i was a bmw mechanic for 3 years i am not sure why they do it this way but it is the proper setup
Repair Help & Product Troubleshooting for 1996 BMW 318

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How many pouns i need to put on 96 bmw 318 is head bolts


Ok its a little diffrent for this vehicle you have a 3 step prossess for each bolt as listed below first tourqe all bolts to 22 ft pounds then when they are all tourqued to that ft pounds then turn each bolt an additonal 90 degrees then a ... 1996 BMW 318

I need a diagram on how to reset the injection pump on a 240D mercedes diesel, 1974 I removed the head and found a broken head bolt, I put the crank on tdc- I put the cam tdc, but did not know that you had to screw in a tool to the injection pump, please help, I am a pretty good mechanic but many gas cars, thanks j.c.


Go post this problem at peachparts.com forum. Those guys can do this in their sleep. ... Mercedes-Benz 300-Class

97 volvo 850 with a milky dipstick, looks like a head gasket is in my future, any special knowledge needed, I've done many but not on this car yet, it'll be my firs, I've learned about the head bolt replacement, what is the torque procedure and any thing special about removing the head and putting it back on ?


Your best bet is to buy a Haynes book on your car from Autozone for $20.00It will tell you if you have stretch bolts or not in your engine. ... 1997 Volvo 850

Hyundai accent xs 1300 1998. Need the torque specs on head bolts, fly wheel, main bearing and big end bearing. Also need to know if the head bolts is strech bolts and do I need to put in new bolts


... Hyundai Accent

1989 nissan stanza 4L 2.0 sohc....been trying to replace head gasket for two days...i need to undo the inlet manifold but am not sure how many bolts need to be removed...my diagram shows either 3,6 or 9. which only applies if i am looking at the bolts which need to be removed. i need to know how many bolts, size, location and how to get to them to remove. thank youj


Hi! Just a tip that may enlighten you on this one. Used to work on one myself, 3 bolts may refer to the top aircleaner case. 8 bolts for the valve cover itself. You will need a size 12 socket to remove this. Hope this helps and good luck! ... 1989 Nissan Stanza

I'm working on a 2003 Buick Lesabre's rear brakes. It appears the bottom of the caliper is fastened with a 12mm bolt -- the top of the caliper doesn't seem to have a head to put a socket on or a torx head. I will be needing to put on new pads AND have the rotors ground, so the rotors will need to come off. The front brakes appear to be more normal with a larger pair of metric bolts holding the caliper on -- BUT the backs look forein to me.


The top of the caliper has a stud. Once you remove the lower caliper bolt, pull the spring-loaded upper portion of the caliper towards the inside of the car. It will come out and you have to pull the caliper off the stud. There is no upper mounting b ... 2003 Buick LeSabre

How many bolts hold Mitsubishi 2.0 head on?The reason I ask is because there are 3 bolts in the middle of the head that are a different size than the other 12 bolts?Do these bolts need to come off to remove the head?Or is the head held down by the 12 bolts only?The repair book I have doesn't say anything about the 3 bolts in the middle.


There are only 10 head bolts on that engine. the 3 bolts your talking about, aren't bolts they are plugs and shouldn't be removed.\015\012 ... Mitsubishi Galant

I need torque specs for a 08 3.5 v6 head bolts rocker bolts and intake bolts i replaced head gasget and need torque specs so i can put it back togeather


... Chevrolet Monte Carlo

I just replaced the intake gaskets on my 2003 pontiac grand am , but when I went to fire it up it was still running like **** come to find out the head gasket on cylinder 3 is blown or the head is cracked. when i go to replace the head or head gasket do I need to repace the bolts on the intake that I just put on or can I get away with using the same ones. I just put them on!


Theres an easier way to fix a blown gasket, its called seal-up you pour it in your radiator and it chemically welds it back together look it up on google most auto shops sell it or something similar, but replaceing the gasket is the best way ... 2003 Pontiac Grand Am

Need to put cylinder head back on a 1984 pontiac sunbird. Need to know all the specs and order for tightening the bolts and how to make sure timing chain is in right place, etc.


... 1984 Pontiac Sunbird Le

I need a drawing of what bolts i have to take out to get a starter out of a 1997 bmw 318i 4 cylinder. i can see the starter but can't determine where and how many bolts are holding it in place and what else do i need to take out to get at the starter so i can replace it. thanks dave.


Generally all starters have two bolts that hold them in.  Plus the associated wiring. ... 1997 BMW 318

I have a 2002 Saturn Vue 2.2L. I thought I needed to replace the timing chain. When we took it apart, we realized that the bolt on the timing chain tensior had snapped off and went into the head. So, we replaced the timing chain tensior, timing chain, the head, all the gaskets. New spark plugs, and a coil pack modular. Now, when we put everything back together, it wont start. When we take the piece that the spark plugs go into, out and turn it upside down, i have spark, but when I put it back in


It sounds like the timing chain was not position correctly. That will cause no ignition spark if the timing is off. Was it positioned correctly upon assembly? ... Saturn Vue

Need to know how to replace the torque converter on transmission for 2000 Ford F250 Superduty truck. Put it in and tried to bolt it up but it didnt work. Need to know when you put the torque converter in how many times do you turn it to make it drop all the way in the transmission


You must turn and wiggle it on the shaft untill it goes all the way on its got to hit those splines just right and itll pop rite on,,some swearing usaually helps out to..lol ... 2000 Ford F250 Super Duty Crew Cabs

Hi I need help with my 2004 Freelander TD4: suddenly blue/white smoke coming out the back of the car ( the car did not over heated the heat gauge was at normal position) notes that there was oil leaking everywhere and that there was oil in the coolant water tank as well, suspect head gasket blown Removed the head, no indication of a blown head gasket, send the head in for testing. Pressure test 100%, so put new head gasket and head bolts, replace oil filter and oil. Start the car and after a


Cracked block. once it heats up the crack gets bigger and the oil gets thinner which makes more oil burn. run car without the oil cap on and see if lots of air/ oil comes out if so thats blow by and you need a new engine. ... Cars & Trucks

I have a Mazda Bravo 1997 model B2600. Am trying to put a new head on the block, although I have set the balance and timing as per the guide the motor shakes and rattles when I start it. I feel it has something to do with positioning the new head on to the existing block, Head bolts or maybe I need different guides for the timeing and balance as it is a new head and older block. The block was in good order when we rplaced the head. Anyone have any ideas as to what the problem is???? Tyler


Most likely you have your plug wires crossed- or bad ones.- Check each plug wire and be sure they are not puled out of their sockets. New is best unless you purchased new when you replaced the head. If the plug wires are good - for 100% sure - ... 1997 Mazda Pickup

A/C Compressor I drove my car from transmission shop home. As I was getting home I heard a rattling noise on passenger side of car under hood. The next day I go out and start car but belt was off. I put belt on (serpentine) hate that stupid belt!!!!!!!!!!!!!!!! and started it. Hear a strange noise, opened hood and saw A/C compressor sitting sideways. A bolt that holds compressor to bracket is broken but don't know where bracket bolts to motor or ******. I need to know where, how many bolts


A basic set of tools and a little patients is all you need. You will need to remove the a/c compressor from the bracket. Once the compressor is out of the way you will see the hidden bolts that hold the bracket in place. \012\012There are several tha ... Cars & Trucks

I need the head bolt torque sequence for a 1996 honda accord 2.2? I also need to know the pounds of pressure and how many passes needed to torque. Thanks


Install the cylinder, then tighten the cylinder head bolts sequentially in 3 steps. step 1. 29 ft. lbs. step 2. 51 ft. lbs. step 3. 72 ft. lbs. ... 1996 Honda Accord

U' m repairing the head on 05 kia rio timing belt slipped and juped time bending all the valves Now putting the head back on I need to know if the head bolts neeed to be replaced and how to torq


Try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your ... 2005 Kia Rio

Need to change the transmission oil & filter on a 1993 Isuzu rodeo v6,4wd/3.2 lt engine , how many bolts need to be [email protected] if possible what size r they as one of them broke, just the head when


... Cars & Trucks

I have a 1998 chevrolet pickup .i need to know the head bolts torque specifications for a 350 so i can put the heads back on it


There is a sequence of tightening the head bolts in a specific order in 2 passes, the preferred method is to tighten all bolts to 22 ft lbs, then add 75 degrees turn to long bolts, 65 degrees to medium bolts, and 55 degrees to short bolts. If you ne ... 1998 Chevrolet C2500

I need head bolt specs for a 1992 bmw 325 i - 1992 BMW 3 Series


Check with a bmw dealer. its an old one. tough to find it. ... 1992 BMW 3 Series

Help please What torque are the cylinder head bolts on peugeot expert 1.6 hdi 2008 i need to put the head back on


No problem the correct setting is ,hmm it says tighten to 20nm then 40nm and then slacken off 130? and tighten 130? ,well this the proverbial brown stuff from a cow to me as when i do these engine i pull down with a speed key then a rachet then my 80 ... Peugeot Liberte

I have a 2001 land rover discovery II and I need the torque settings so I can put the engine back togather. Im not sure how tight to tighten the head cylinder bolts or the manifold bolts.


Do not reuse the old head bolts. These are torque-to-yeild type bolts and stretch when torqued down. \015\012\015\012Starting in the center and working your way outward:\015\012\015\0121st step - 15 ft-lbs\015\012 ... 2001 Land Rover Discovery Series II

I just changed the cylinder head gasket on my 1986 Toyota Corolla 4ALC engine and can't find my repair manual (aaargh). I need to know the touque sequence and force spec for the head bolts. Many Thanks! Bob


... Toyota Corolla

I just re surfaced the head on me 2007 suzuki forenza and need to know how I have to put it back on. Can you give me a diagrahm with the torque specks and order in which to tighten the bolts down it h


... Suzuki Forenza
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.2388 seconds