Having problems with your 1995 Honda Accord ?

BELT REPLACEMENT HOW TO REPLACE TIMING BELT AT HONDA ACCORD 2.0 1995 LOOKING FOR MANUAL, OR ANY DRAWINGS WITH MARKS......

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 1995 Honda Accord

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

BELT REPLACEMENT HOW TO REPLACE TIMING BELT AT HONDA ACCORD 2.0 1995 LOOKING FOR MANUAL, OR ANY DRAWINGS WITH MARKS......


Http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528005f4af ... 1995 Honda Accord

I have replaced the engine top of my toyota hilux KZTE 2003 model, due to cracks in the engine top. I did not align all the timing marks on the engine before removing the timing belt. I did not adjust or remove any part of the timing gear on the engine block. I tried to set the cam and crank position to TDC but if go according to the workshop manual, the timing mark on the camshaft is 180deg shifted from the timing mark on the engine.SEE page 2D-6 of workshop manual for hilux models Oct1997 thro


... Toyota Pickup

The vehicle has fire out of the coil to the cap but nothing out of the cap to the wires. I have fuel. Replaced the timing belt and the timing marks are all on according to the manual. Car turns over with no problem will not fire. Car was being driven as it quit. Replaced cap and rotor also. Have not replaced pick up coil in the distributor. I was told that you can unplug the pick up and it should still run.


Hi\015\012Defective ignition wires will block the necessary voltage, which results in a cylinder misfire or no-fire condition. Several tests allow the vehicle owner to pinpoint the location and causes of faulty ignition w ... 2001 Volkswagen Cabrio

I have 99 Ford escort 2.0. I cannot get it running now. The trouples codes show cylinder 3 misfire and cylinder 4 misfire. I have replaced the coil, spark plugs, sp wires, crankshft sensor, and timing belt. I dont know where else to look. I set the timing according to the manual, one year ago and it ran fine. I just replaced it again assuming timing may be the problem. I went to the Ford Service Ctr here locally and they said they have the same problem with a Ford and havent figured out what is


Fuel pump....if its got a spark, and the valves are timed... check the obvious...air and fuel. ... 2000 Ford Focus

Timing belt 1983 Honda Prelude reference timing marks for timing belt replacement. I dont have manual and thought i might find sollution on the net way to much hassle for a simple drawing.


BEFORE U TAKE THE TIMING BELT OFF PUT THE CRANK SHAFT ON ITS MARK.IF THE CAM MARKS ARE NOT LINED UP THEN ROTATE THE CRANK 180.THEN U CAN MARK THE POSITION OF THE CAM & CRANK GEARS W/A CRAYON,WHITE OUT ECT.AS LONG AS THE GEARS DO NOT MOVE THEN U W ... 1983 Honda Prelude

Ive been trying to set the timing on a 95' volvo 850. first replaced water pump 2 days before. finances kept me from replaceing any addition componants at that time. now im paying for it. the belt broke. is it possible to break the syncronization of the cams and the crank shaft. since the belt broke i didnt have the chance to set the marks according to the book. i have hand cranked both of the cams and crank shaft counter clockwise and clockwise to put everything on its mark. with the "clockwise


It is possible to set the timing wrong....if the belt broke well running I believe this is an interference motor..meaning if the timing is off the cylinder can move up and smack a Valve being exhaust or intake. which means a valve can break or bend c ... 1995 Volvo 850

Water pump I am going to replace the water pump and the manual calls for top dead center cyl 1. Why? I know I am going to be removing the timing belt but as long as it is marked - why does it matter where the pistons are. Also I #1 plug seems to be behind the gen. mount. Spark plug hard to get any trick? Also how in the world am I going to tell TDC with this set up. I am assuming that piston 1 is top left - how I'm going to determine TDC I don't know at least the way the book explains it - look


Once you remove the timing belt covers,rotate engine,by hand via cranckshaft bolt (only in direction of normal engine rotation,i believe clockwise on that) and aligne all timing marks. At this time your engine is at #1 tdc..Follow manual and change b ... 1993 Dodge Spirit

I know just enough about car mechanics to be dangerous. I replaced the water pump and put the timing belt back on just the way it came off and it must have slippied a tooth. I need to know how to reset all the timing marks. 1 of the manuals send that when you release the pin holding the belt tensioner, the holes should still line up. My plunger moves upwards about about 1/4 inch, does that mean it needs replacing. As far as aligning the timing marksI know it all starts with find the TDC but how


TDC can be found by re-installing the cover and referencing the "0" mark on the timing scale with the hash mark on the pulley. If there isn't one, your other option is to make a reference mark on the pulley and a reference mark in the same place on a ... Chrysler Sebring

Timing belt I've replaced the timing belt but the timing is out. The car can go up to 70km per hour and cut out at 3000 refs Is there some marks that I need to look for on the timing belt and the pully?


There are a couple of marks you can look for do you have a 16v or an 8 v if its a 16v you need to line up the two marks on your cams with each other and piston number one must be on "tdc" then just turn your engine by hand a couple of time to make su ... 1996 Ford Escort 4 Door

Where is the timing mark for the camshaft on a 2000 Daewoo Lanos? hey would you send me any pictures of how they look like the timing marks of a 2000 daewoo. i installed the timing belt on my car but is not running at all. i would like to know if you can send me any timing marks to see what i did wrong when i replaced the head gasket.


Single cam or twin?\015\012\015\012\015\012 ... 1999 Daewoo Lanos

I replaced my timing belt and after replacing it the engine missed a little on idle, but ran beautiful at 60-75 mph. I took it into a shop and was told I was off one tooth. I've now again removed the belt and somehow the camshaft jumped. I put the arrows back to linement as well as the crankshaft. but the car wont start. when I looked at the cams the intake has indented on the spocket "front and with a arrow pointing up" with the timing mark on the 9'oclock position. on the exhuast it also has t


Hi mike, i am not an expert on these but i will try to give you ahand,several vehicles i have done ,all landcruisers i have hjad the experience of seeing the cam jump back it is as if they are loaded up. i found that you can turn the cam forward to t ... 2002 Chrysler PT Cruiser

Hi I have Peugeot 307 SW 2.0 litre diesel (2003), engine - DW10ATED. Time has come to replace a timing belt. I would like to do it myself. Read through many forums but no exact work instructions could find. Read through Haynes manual but if I follow it, I would have to take half of my car apart just to replace a cam belt (i.e. remove whole exhaust system as if it is not removed, the front pipe flexible section will be damaged when the right-hand engine mounting is detached). Looks strange, bec


There is specail tool set for this job, the set includes the tensioner setting tool, without that tool u run the risk of breaking the belt or haviong it come off, here is a link to the tool set.\015\012here is the number of kit\015\012 ... Peugeot 405

Timing mark-specs 2002 ford focus 2.0 liter single, i had to replace the timing belt looking for the timing mark to set it.


ADVISE YOU NOT TO TOUCH THIS UNLESS UR MECHANILLY COMPENENT YOU NEED SPECIAL TIMING PINS & BAR FOR THIS & ARE NOT THE EASIEST TO TIME UP. ... 2002 Ford SVT Focus

Carnt find timing chain marks on a 2002 2.0 20v alt engine ive replaced new valves timing belt ect but i carnt find timing chain marks checked in manual ask dealers but no one knows


Join a VW forum you'll have more luck finding what you need. Try VWVortex ... Volkswagen Passat

Replacing the timing belt 2000 grand am looking for timing marks timing marks


Your crank and cams all have marks on them, they might be just dots, but they are there, your new belt should have marks on it too. Line up all the marks, and you should be all set. I take a white out marker to make them stand out better, and I mark ... Pontiac Grand Am

I am in the middle of replacing the timing belt on a 05 honda odyssey touring, before removing the old belt, the manual is saying to turn the crankshaft pulley to its white mark [which i can see] lines up with the pointer [B] on the engine block [ which i can also see], the manual also says to set the No. 1 piston at top dead center TDC by aligning the pointer on the front cover with the No.1 piston on the front camshaft pulley, the problem is as of now with the old belt still in place, when i t


Remember that for every rotation of the cam there two rotations of the crank. Rotate the crank a further 360 and bring the piston to TDC and the white mark should now align on the cam. ... 2005 Honda Odyssey

I just replaced the timing belt on my 2003 lexus rx300 3.0 liter engine with vvt and dohc. i've had no problems with the car ever. i know the right cam sprocket moved slightly while installing the timing belt but i moved it back (as close as i could). the timing marks on the right sprocket are hard to align because they are hard to see and the manual i'm using isn't making sense to an aircraft mechanic like me. the engine seems to run ok, but is probably hard to tell with such a small misadjustm


Hi!! \015\012\015\012Click on the following link for step by step instruccions on timing belt removal and installation. ... Lexus RX 300

Replaced timing belt on a 97 contour. i know that the cams are lined up (kind of a full proof methed that ford used). the second notch on crank pulley lined up with the oil pan marking (with the side of the v that is closest to fire wall) this looked to be TDC center, by settiing and watching a screw driver on the piston. now with timing light, #1 plug apears to fire when second notch on crank pully is just about to reach the front side of the v oil pan mark. car will not fire on its own or wit


... Ford Contour

My 2006 Toyota Rav4 it has 70,000 miles on it. I look in the owner maintenance manual and it doesn't say anything about replace timing belt at 60,000 miles like many others. Does this vehicle use timing belt or chain?


Hello. Welcome to FixYa. \015\012Please allow us to assist you.\015\012\015\012We have good news for you. \015\012\015\012Your vehicle does not have a timing belt. Your vehicle has a timing chain; there is no suggested r ... 2006 Toyota RAV4

Im replacing the timing belt on my 1999 caravan 3.0 liter. i found tdc on the #1 cyl, assuming its the closest on the right of the engine as you look at it with the main shaft facing you. i then lined the marks on the cam sprockets to the notches provided in the casting on the left and the stamped notch on the right. when i turn the engine over, it acts as if i havent even put the timing belt on (meaning the starter turns fast with no sign of spark)


#1 cylinder is to the left as you look at the belt. Either way, I recommend you use the timing mark on the crankshaft, which is more accurate way to get TDC (see diagram below). The key to getting timing belt right is to first get all the sprockets ... Dodge Caravan

Driving 92 Honda Accord and the engine stopped dead. Turns over but will not start. Checked the timing belt and it's fine and everything looks great and sounds normal. Any ideas as where to look for such a problem 92 Honda Accord 2.2 manual with A/C Derrick [email protected]


Ignition control module or ignition switch ... Honda Accord

Timing marks looking to replace timing belt on 2001 2.0l tdi grand vitara but cannot locate any marks on pump or cam pully. any ideas?


Autozone.com has free repair info. They gave a great decription of the 3 timing chains and marks for my 2001 V6 2.5L engine. The motor ran perfect with their help. ... 2001 Suzuki Grand Vitara

Can't find timing mark on 94 honda accord dx replacing old timing belt want to line up the marks on the crankshaft


... 1994 Honda Accord

I have replaced the timing belt on my 1999 mazda protege 1.6 . My Hayes repair manual was vague about the timing. I asked a tech on this site for help and was told ''look at the camshaft gears and the back gear has an ''I'' on it and the front one has an ''E'' on it. when those are facing straight up look at the closest point in between the cam gears and you will see two sets of notches and the top set at the closest points of the two cam gears will face each other the left cam at 3 o;clock and


The information the previous tech gave you was correct, however if your marks were not aligned (slightly pointing down) on removal then you have to either reinstall in the same position, or adjust the crank position after you align the cams. Y ... 1999 Mazda Protege

97 mazda 626 dx 2.0. manual shift, crank but won't start,install used engine w/less than 50k miles, after original engine lose power replace valve stem seals, timing belt, w/pump,oil pump,distributor cap & rotor,wires,fuel pump, MAP sensor(after code), timing marks are aligned correctly.engine starts and run on 3 cyl after 1 plug is removed,no matter which plug/wire,but after re-installing plug,engine cranks but won't start,i am getting fuel and the wires are sparking at plugs,should i replace E


First check the spark plugs.\015\012\015\012If your engine cranks normally but will\015\012not start because it has no spark, or it stalls and won't restart because it\015\012has no spark, the problem may be due to any of the follo ... 1997 Mazda 626
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.5397 seconds